Hello, I did some tests again to check, if there is something new. The complete Bootlog is attached.
What is important: With current U-Boot 2019.07, the Ethernet is now detected in U-Boot: > Net: phy interface7 > eth0: ethernet@1c30000 But within installer, there is no ethernet card detected. Is it possible, that there is an important kernel module missing? If i can do some tests for debug, please let me know. Thank you for your great support. Best regards Bernhard
U-Boot SPL 2019.07+dfsg-1 (Jul 08 2019 - 23:41:40 +0000)
DRAM: 2048 MiB
Trying to boot from MMC1
U-Boot 2019.07+dfsg-1 (Jul 08 2019 - 23:41:40 +0000) Allwinner Technology
CPU: Allwinner A83T (SUN8I 1673)
Model: Banana Pi BPI-M3
DRAM: 2 GiB
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... Unable to use mmc 1:0... In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
Bus usb@1c19000: No host cable detected: Port not available.
Bus usb@1c1a000: USB EHCI 1.00
scanning bus usb@1c1a000 for devices... Device NOT ready
Request Sense returned 02 3A 00
3 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 2 1 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
1575 bytes read in 3 ms (512.7 KiB/s)
## Executing script at 43100000
Mainline u-boot / new-style environment detected.
4395520 bytes read in 430 ms (9.7 MiB/s)
23237 bytes read in 18 ms (1.2 MiB/s)
23130363 bytes read in 2256 ms (9.8 MiB/s)
Booting the Debian installer...
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Loading Ramdisk to 489f0000, end 49fff0fb ... OK
Loading Device Tree to 489e7000, end 489efac4 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.2.0-2-armmp (debian-ker...@lists.debian.org) (gcc version 8.3.0 (Debian 8.3.0-21)) #1 SMP Debian 5.2.9-2 (2019-08-21)
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Banana Pi BPI-M3
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 16 MiB at 0x6f000000
[ 0.000000] percpu: Embedded 20 pages/cpu s52044 r8192 d21684 u81920
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 521984
[ 0.000000] Kernel command line: console=ttyS0,115200
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 2016224K/2097152K available (9216K kernel code, 1138K rwdata, 2836K rodata, 2048K init, 321K bss, 64544K reserved, 16384K cma-reserved, 1310720K highmem)
[ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x48/0x534 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] ftrace: allocating 34053 entries in 67 pages
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000011] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000026] Switching to timer-based delay loop, resolution 41ns
[ 0.001248] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.002681] Console: colour dummy device 80x30
[ 0.002777] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.002794] pid_max: default: 32768 minimum: 301
[ 0.003084] LSM: Security Framework initializing
[ 0.003169] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.003357] AppArmor: AppArmor initialized
[ 0.003373] TOMOYO Linux initialized
[ 0.003532] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.003553] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.005462] CPU: Testing write buffer coherency: ok
[ 0.006334] /cpus/cpu@0 missing clock-frequency property
[ 0.006359] /cpus/cpu@1 missing clock-frequency property
[ 0.006379] /cpus/cpu@2 missing clock-frequency property
[ 0.006398] /cpus/cpu@3 missing clock-frequency property
[ 0.006420] /cpus/cpu@100 missing clock-frequency property
[ 0.006442] /cpus/cpu@101 missing clock-frequency property
[ 0.006466] /cpus/cpu@102 missing clock-frequency property
[ 0.006491] /cpus/cpu@103 missing clock-frequency property
[ 0.006510] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.007533] Setting up static identity map for 0x40300000 - 0x403000ac
[ 0.008793] ARM CCI driver probed
[ 0.009383] sunxi multi cluster SMP support installed
[ 0.009937] rcu: Hierarchical SRCU implementation.
[ 0.013715] EFI services will not be available.
[ 0.014638] smp: Bringing up secondary CPUs ...
[ 0.016107] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.017721] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.019117] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.020733] CPU4: thread -1, cpu 0, socket 1, mpidr 80000100
[ 0.022415] CPU5: thread -1, cpu 1, socket 1, mpidr 80000101
[ 0.023944] CPU6: thread -1, cpu 2, socket 1, mpidr 80000102
[ 0.025512] CPU7: thread -1, cpu 3, socket 1, mpidr 80000103
[ 0.025710] smp: Brought up 1 node, 8 CPUs
[ 0.025760] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[ 0.025769] CPU: All CPU(s) started in SVC mode.
[ 0.027773] devtmpfs: initialized
[ 0.036725] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.037455] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.037499] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.039834] pinctrl core: initialized pinctrl subsystem
[ 0.041713] DMI not present or invalid.
[ 0.042554] NET: Registered protocol family 16
[ 0.046173] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.047295] audit: initializing netlink subsys (disabled)
[ 0.047737] audit: type=2000 audit(0.044:1): state=initialized audit_enabled=0 res=1
[ 0.049540] No ATAGs?
[ 0.049904] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.049922] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.050970] Serial: AMBA PL011 UART driver
[ 3.818099] alg: No test for lzo-rle (lzo-rle-generic)
[ 3.818589] alg: No test for lzo-rle (lzo-rle-scomp)
[ 3.824354] vgaarb: loaded
[ 3.825481] media: Linux media interface: v0.10
[ 3.825530] videodev: Linux video capture interface: v2.00
[ 3.825594] pps_core: LinuxPPS API ver. 1 registered
[ 3.825603] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giome...@linux.it>
[ 3.825628] PTP clock support registered
[ 3.827717] clocksource: Switched to clocksource arch_sys_counter
[ 3.939008] VFS: Disk quotas dquot_6.6.0
[ 3.939153] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 3.940416] AppArmor: AppArmor Filesystem Enabled
[ 3.953721] NET: Registered protocol family 2
[ 3.955076] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 3.955118] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 3.955201] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 3.955334] TCP: Hash tables configured (established 8192 bind 8192)
[ 3.955591] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 3.955846] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 3.956347] NET: Registered protocol family 1
[ 3.956395] NET: Registered protocol family 44
[ 3.956419] PCI: CLS 0 bytes, default 64
[ 3.957167] Trying to unpack rootfs image as initramfs...
[ 5.737534] Freeing initrd memory: 22592K
[ 5.742064] Initialise system trusted keyrings
[ 5.742136] Key type blacklist registered
[ 5.742433] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 5.751394] zbud: loaded
[ 5.754176] Platform Keyring initialized
[ 5.754201] Key type asymmetric registered
[ 5.754212] Asymmetric key parser 'x509' registered
[ 5.754295] bounce: pool size: 64 pages
[ 5.754370] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 5.754685] io scheduler mq-deadline registered
[ 5.764655] sun8i-a83t-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver
[ 5.774403] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.777270] Serial: AMBA driver
[ 5.781054] libphy: Fixed MDIO Bus: probed
[ 5.781781] mousedev: PS/2 mouse device common for all mice
[ 5.786822] ledtrig-cpu: registered to indicate activity on CPUs
[ 5.788985] NET: Registered protocol family 10
[ 5.838315] Segment Routing with IPv6
[ 5.838501] mip6: Mobile IPv6
[ 5.838528] NET: Registered protocol family 17
[ 5.838829] mpls_gso: MPLS GSO support
[ 5.838947] ThumbEE CPU extension supported.
[ 5.838966] Registering SWP/SWPB emulation handler
[ 5.840334] registered taskstats version 1
[ 5.840349] Loading compiled-in X.509 certificates
[ 6.171974] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 6.172099] Loaded X.509 cert 'Debian Secure Boot Signer: 00a7468def'
[ 6.172327] zswap: loaded using pool lzo/zbud
[ 6.172969] AppArmor: AppArmor sha1 policy hashing enabled
[ 6.188039] sun8i-a83t-r-pinctrl 1f02c00.pinctrl: 1f02c00.pinctrl supply vcc-pl not found, using dummy regulator
[ 6.188481] sunxi-rsb 1f03400.rsb: RSB running at 3000000 Hz
[ 6.191000] ac100-rtc ac100-rtc: DMA mask not set
[ 6.194363] ac100-rtc ac100-rtc: registered as rtc0
[ 6.194380] ac100-rtc ac100-rtc: RTC enabled
[ 6.201072] sun8i-a83t-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 6.202082] random: fast init done
[ 6.202111] sun8i-a83t-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
[ 6.203161] printk: console [ttyS0] disabled
[ 6.223441] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 44, base_baud = 1500000) is a U6_16550A
[ 6.717856] random: crng init done
[ 6.720304] printk: console [ttyS0] enabled
[ 7.021874] sun8i-a83t-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pg not found, using dummy regulator
[ 7.056420] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 45, base_baud = 1500000) is a U6_16550A
[ 7.065670] serial serial0: tty port ttyS1 registered
[ 7.072386] sun8i-a83t-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pd not found, using dummy regulator
[ 7.084277] ac100-rtc ac100-rtc: setting system clock to 1970-01-01T01:00:18 UTC (3618)
[ 7.103275] Freeing unused kernel memory: 2048K
[ 7.108157] Run /init as init process
[ 7.412895] sun8i-a83t-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
[ 7.437692] usbcore: registered new interface driver usbfs
[ 7.440879] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 7.443481] usbcore: registered new interface driver hub
[ 7.453302] dwmac-sun8i 1c30000.ethernet: PTP uses main clock
[ 7.454601] sun8i-a83t-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
[ 7.456895] usbcore: registered new device driver usb
[ 7.483824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.495025] ehci-platform: EHCI generic platform driver
Starting system log daemon: syslogd, klogd.
signature.asc
Description: This is a digitally signed message part
