Your message dated Mon, 22 Jul 2013 01:12:11 +0200
with message-id <[email protected]>
and subject line dealing with old debian-installer bugs
has caused the Debian Bug report #606055,
regarding Expert installer freezes when selecting "Configure MD devices"
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)
--
606055: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=606055
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Package: debian-installer
Version: 20101127 (6.0 squeeze)
Just trying out Debian for the first time, installing it over the top of a
Gentoo box. I configured all the partitions (mostly by accepting the existing
software-RAID configuration and leaving it unchanged except for reformatting
everything.)
After this the main menu came up with "Configure MD devices" which I selected,
and half an hour later it's still sitting at a blank (blue) screen.
This is a network install, booted over TFTP and running through SSH. Syslog
says:
Dec 6 00:00:15 kernel: [ 644.380596] md1: detected capacity change from 0 to
725173403648
Dec 6 00:00:15 kernel: [ 644.389755] md1: unknown partition table
Dec 6 00:00:16 kernel: [ 644.814460] device-mapper: uevent: version 1.0.3
Dec 6 00:00:16 kernel: [ 644.815527] device-mapper: ioctl: 4.15.0-ioctl
(2009-04-01) initialised: [email protected]
Dec 6 00:00:16 partman: No matching physical volumes found
Dec 6 00:00:16 partman:
Dec 6 00:00:16 partman: No volume groups found
Dec 6 00:00:16 partman:
Dec 6 00:00:16 partman: Reading all physical volumes. This may take a
while...
Dec 6 00:00:16 partman-lvm:
Dec 6 00:00:16 partman-lvm: No volume groups found
Dec 6 00:00:16 partman-lvm:
Dec 6 00:08:21 partman: mke2fs 1.41.12 (17-May-2010)
Dec 6 00:09:02 partman: mke2fs 1.41.12 (17-May-2010)
Dec 6 00:09:10 partman: mke2fs 1.41.12 (17-May-2010)
Dec 6 00:09:12 kernel: [ 1181.567882] EXT4-fs (md0): mounted filesystem with
ordered data mode
Dec 6 00:09:12 kernel: [ 1181.648716] EXT4-fs (md2): mounted filesystem with
ordered data mode
Dec 6 00:09:13 kernel: [ 1181.758433] EXT4-fs (md1): mounted filesystem with
ordered data mode
Dec 6 00:09:14 apt-install: Queueing package e2fsprogs for later installation
Dec 6 00:09:16 main-menu[3021]: INFO: Falling back to the package description
for mdcfg
Dec 6 00:09:16 main-menu[3021]: INFO: Falling back to the package description
for mdcfg
Dec 6 00:09:18 kernel: [ 1187.001596] JBD: barrier-based sync failed on md0-8
- disabling barriers
Dec 6 00:11:57 main-menu[3021]: INFO: Falling back to the package description
for mdcfg
Dec 6 00:11:57 main-menu[3021]: INFO: Menu item 'mdcfg' selected
Dec 6 00:11:57 main-menu[3021]: WARNING **: Unable to set title for mdcfg.
Dec 6 00:11:57 apt-install: Queueing package mdadm for later installation
Dec 6 00:48:10 sshd[15349]: WARNING: /etc/ssh/moduli does not exist, using
fixed modulus
Dec 6 00:48:14 sshd[15349]: Accepted password for installer from 192.168.0.14
port 53709 ssh2
Last two messages are from my login to get this. /proc/mdstat says all RAID
arrays are functioning normally. I just tried reconnecting and doing it again
with the same result. New log messages are:
Dec 6 00:58:09 debconf: Setting debconf/language to en_AU:en
Dec 6 00:58:11 debconf: Setting debconf/priority to low
Dec 6 00:58:11 debconf: Setting debconf/language to en_AU:en
Dec 6 00:58:11 main-menu[15390]: INFO: Falling back to the package
description for mdcfg
Dec 6 00:58:17 main-menu[15390]: INFO: Falling back to the package
description for mdcfg
Dec 6 00:58:17 main-menu[15390]: INFO: Menu item 'mdcfg' selected
Dec 6 00:58:17 main-menu[15390]: WARNING **: Unable to set title for mdcfg.
Guess I should skip this step...
--- End Message ---
--- Begin Message ---
reassign 690832 choose-mirror
reassign 687488 netcfg
retitle 709319 wheezy 7.1: scanning for more DVDs is confusing
tags 709319 + confirmed
tags 626219 + confirmed
reassign 616722 partman-md
reassign 616125 partman-crypto
thanks
Hi,
thank you for submitting bug reports concering debian-installer, much
appreciated.
I read through all the bugs mentioned here (and I'm sure they were read by
several people at the time they were submitted) and am closing them now as/if
- they (finally) indicated success and/or
- I know from first hand experience that the functionality is working in
Wheezy and/or
- they only contained very little information and/or
- they contained user errors and/or
- they have been from a development phase where things were not stable and/or
- they are very old and/or
- they are wishlist but rather special + exotic and not have been acted on for
years. (See http://blog.liw.fi/posts/wishlist-bugs/ why it's often useful to
close wishlist bugs.)
If I've closed a bug incorrectly please do reply (it's easy to reopen and I'll
do if requested) or just file a new one - and that's often better, as the bug
log will be clearer and shorter and not contain cruft.
cheers,
Holger
signature.asc
Description: This is a digitally signed message part.
--- End Message ---
