Your message dated Sun, 27 Jul 2008 14:34:26 +0200
with message-id <[EMAIL PROTECTED]>
and subject line Re: Bug#297175: Debian install - please mention need to run
dexconf after X configuration
has caused the Debian Bug report #297175,
regarding Debian install - please mention need to run dexconf after X
configuration
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [EMAIL PROTECTED]
immediately.)
--
297175: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=297175
Debian Bug Tracking System
Contact [EMAIL PROTECTED] with problems
--- Begin Message ---
Package: installation-reports
Debian-installer-version: 2005-02-27 image from debian website about 4 weks ago
uname -a: Linux home 2.4.27-speakup #1 Thu Aug 19 21:46:14 CEST 2004 i686
GNU/Linux
Date: 2005-02-27
Method: From CD
What did you boot off? CD
If network install, from where? download from debian.org not proxied
Machine: desktop w/Slot-A motherboard
Processor: AMD K-7 (800MHz)
Memory:256M
Root Device: hda0
Root Size/partition table:
Device Boot Start End Blocks Id System
/dev/hda1 1 99 795186 82 Linux swap
/dev/hda2 * 100 1405 10490445 83 Linux
/dev/hda3 1406 9729 66862530 5 Extended
/dev/hda5 1406 2717 10538608+ 83 Linux
/dev/hda6 2718 3481 6136798+ 83 Linux
/dev/hda7 3482 3544 506016 82 Linux swap
/dev/hda8 3545 9729 49680981 83 Linux
Output of lspci and lspci -n:
lspci:
0000:00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate]
System Controller (rev 25)
0000:00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-751 [Irongate] AGP
Bridge (rev 01)
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-756 [Viper] ISA (rev
01)
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-756 [Viper] IDE
(rev 03)
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-756 [Viper] ACPI (rev 03)
0000:00:07.4 USB Controller: Advanced Micro Devices [AMD] AMD-756 [Viper] USB
(rev 06)
0000:00:09.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
0000:00:0a.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
0000:00:0b.0 Multimedia audio controller: Ensoniq ES1370 [AudioPCI]
home:/var/log# lspci -n
0000:00:00.0 0600: 1022:7006 (rev 25)
0000:00:01.0 0604: 1022:7007 (rev 01)
0000:00:07.0 0601: 1022:7408 (rev 01)
0000:00:07.1 0101: 1022:7409 (rev 03)
0000:00:07.3 0680: 1022:740b (rev 03)
0000:00:07.4 0c03: 1022:740c (rev 06)
0000:00:09.0 0200: 1186:1300 (rev 10)
0000:00:0a.0 0300: 5333:8a01 (rev 01)
0000:00:0b.0 0401: 1274:5000
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [ 0]
Configure network HW: [ 0]
Config network: [I had a DSL modem connected directly to the computer,
which requires pppoe. There was no
way to bring up pppoe from the installer; I could not access the installation
archive until I installed a router
(to bring up pppoe and provide a standard network interface to the computer.)
This is OK but it should be explained to
the user so he/she will have the required hardware.]
Detect CD: [ 0]
Load installer modules: [ 0]
Detect hard drives: [ 0]
Partition hard drives: [ 0]
Create file systems: [ 0]
Mount partitions: [ 0]
Install base system: [ 0]
Install boot loader: [ 0]
Reboot: [ 0]
Comments/Problems:
__Please__ provide a statement in the xfree86 configuration sequence that you
have to run dexconf to actually write
out the XF86Config file, or just run it automatically after the configuration.
This didn't used to be required! It
took me two days to figure it out; I thought I was doing something else wrong
and did considerable damage. It is
mentioned in the FAQ, but everything else is spelled out in the screen
instructions and it would be much easier if
you just had a screen like
"You must run dexconf to actually generate a new XF86Config file. Run dexconf
now? Yes/No."
When I finally found it in the FAQ and ran dexconf, x-windows started with no
trouble.
Otherwise the installer worked extremely well. I have use linux since
Slackware 0.9 and this is one of the best.
Thanks for all the hard work.
Dan Woodard
[EMAIL PROTECTED]
--- End Message ---
--- Begin Message ---
On Sun, Feb 27, 2005 at 01:18:15PM -0500, Dan Woodard wrote:
> __Please__ provide a statement in the xfree86 configuration sequence
> that you have to run dexconf to actually write out the XF86Config
> file, or just run it automatically after the configuration. This
> didn't used to be required!
X.org configuration is now handled automatically by the relevant
packages. I am thus closing this (pretty old) bug report.
Cheers,
--
Jérémy Bobbio .''`.
[EMAIL PROTECTED] : :Ⓐ : # apt-get install anarchism
`. `'`
`-
signature.asc
Description: Digital signature
--- End Message ---