I suppose that it may be that the ramdisk.gz and zimage kernel files I used are for the SS4000E and will not work in the 4020. The SS4000E uses a 7210 board and the 420 uses a 7220.
Does anyone know if 7220/4020 versions are available anywhere? CJW -----Original Message----- From: Chris Wilkinson [mailto:kins...@verizon.net] Sent: Friday, July 13, 2012 10:04 AM To: debian-arm@lists.debian.org Subject: Cannot boot Freestor 4020 (SS-4000E) It hangs on boot but boots from the console using fis load, exec. There is one disk is inserted which is disk1/4 of what was the RAID5 set. Not sure what to try next to get it to boot on its own. Chris EM-438/EM-7220 ver.AG0 2006-05-23 == Executing boot script in 1.000 seconds - enter ^C to abort RedBoot> fis load ramdisk.gz RedBoot> fis load zImage RedBoot> exec Using base address 0x01008000 and length 0x00200000 Uncompressing Linux... done, booting the kernel. <<hangs here>> If I start from the console it boots. So it seems the fis images are OK. Power-on EM-438/EM-7220 ver.AG0 2006-05-23 == Executing boot script in 1.000 seconds - enter ^C to abort ^C RedBoot> fis load ramdisk.gz RedBoot> fis load zImage RedBoot> exec -c "console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000" -r 0x01800000 -w 5 About to start execution at 0xa0008000 - abort with ^C within 5 seconds Using base address 0x01008000 and length 0x00200000 Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32-5-iop32x (Debian 2.6.32-45) (da...@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Sun May 6 07:47:32 UTC 2012 [ 0.000000] CPU: XScale-80219 [69052e30] revision 0 (ARMv5TE), cr=0000397f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Lanner EM7210 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 [ 0.000000] Kernel command line: console=ttyS0,115200 rw root=/dev/ram mem=256M@0xa0000000 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 256MB = 256MB total [ 0.000000] Memory: 251776KB available (3084K code, 444K data, 112K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:32 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 599.65 BogoMIPS (lpj=2998272) [ 0.220000] Security Framework initialized [ 0.220000] SELinux: Disabled at boot. [ 0.220000] Mount-cache hash table entries: 512 [ 0.220000] Initializing cgroup subsys ns [ 0.220000] Initializing cgroup subsys cpuacct [ 0.220000] Initializing cgroup subsys devices [ 0.220000] Initializing cgroup subsys freezer [ 0.220000] Initializing cgroup subsys net_cls [ 0.220000] CPU: Testing write buffer coherency: ok [ 0.220000] devtmpfs: initialized [ 0.220000] regulator: core version 0.5 [ 0.220000] NET: Registered protocol family 16 [ 0.220000] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 0.220000] pci 0000:00:01.0: PME# disabled [ 0.220000] pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot [ 0.220000] pci 0000:00:05.0: PME# disabled [ 0.220000] pci 0000:00:05.1: PME# supported from D0 D1 D2 D3hot [ 0.220000] pci 0000:00:05.1: PME# disabled [ 0.220000] pci 0000:00:05.2: PME# supported from D0 D1 D2 D3hot [ 0.220000] pci 0000:00:05.2: PME# disabled [ 0.220000] PCI: bus0: Fast back to back transfers disabled [ 0.230000] bio: create slab <bio-0> at 0 [ 0.230000] vgaarb: loaded [ 0.240000] NET: Registered protocol family 2 [ 0.240000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.240000] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 0.250000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) [ 0.250000] TCP: Hash tables configured (established 8192 bind 8192) [ 0.250000] TCP reno registered [ 0.250000] NET: Registered protocol family 1 [ 0.250000] Unpacking initramfs... [ 0.950000] Freeing initrd memory: 4096K [ 0.950000] NetWinder Floating Point Emulator V0.97 (double precision) [ 0.950000] audit: initializing netlink socket (disabled) [ 0.950000] type=2000 audit(0.950:1): initialized [ 0.970000] VFS: Disk quotas dquot_6.5.2 [ 0.970000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.970000] msgmni has been set to 500 [ 0.970000] alg: No test for stdrng (krng) [ 0.970000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.970000] io scheduler noop registered [ 0.970000] io scheduler anticipatory registered [ 0.970000] io scheduler deadline registered [ 0.970000] io scheduler cfq registered (default) [ 0.980000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.980000] serial8250.0: ttyS0 at MMIO 0xfe800000 (irq = 28) is a 16550A [ 1.330000] console [ttyS0] enabled [ 1.330000] physmap platform flash device: 02000000 at f0000000 [ 1.330000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank [ 1.350000] Intel/Sharp Extended Query Table at 0x0031 [ 1.350000] Intel/Sharp Extended Query Table at 0x0031 [ 1.350000] Using buffer write method [ 1.360000] cfi_cmdset_0001: Erase suspend on write enabled [ 1.360000] Searching for RedBoot partition table in physmap-flash.0 at offset 0x7e0000 [ 1.500000] 10 RedBoot partitions found on MTD device physmap-flash.0 [ 1.500000] Creating 10 MTD partitions on "physmap-flash.0": [ 1.510000] 0x000000000000-0x000000040000 : "RedBoot" [ 1.510000] 0x000000040000-0x000000240000 : "zImage" [ 1.520000] 0x000000240000-0x000000640000 : "ramdisk.gz" [ 1.530000] 0x000000640000-0x000000700000 : "wmdata" [ 1.530000] 0x000000700000-0x000000740000 : "rammode" [ 1.540000] 0x000000740000-0x000000760000 : "naskey" [ 1.550000] 0x000000760000-0x0000007a0000 : "log" [ 1.550000] 0x0000007a0000-0x0000007c0000 : "vendor" [ 1.560000] 0x0000007c0000-0x0000007c1000 : "RedBoot config" [ 1.560000] mtd: partition "RedBoot config" doesn't end on an erase block -- force read-only [ 1.580000] 0x0000007e0000-0x000000800000 : "FIS directory" [ 1.580000] mice: PS/2 mouse device common for all mice [ 1.590000] i2c /dev entries driver [ 1.590000] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6 [ 1.610000] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 [ 1.610000] i2c i2c-0: failed,FF11,11,05 [ 1.640000] iop-adma iop-adma.0: Intel(R) IOP: ( cpy intr ) [ 1.660000] iop-adma iop-adma.1: Intel(R) IOP: ( cpy intr ) [ 1.660000] TCP cubic registered [ 1.670000] NET: Registered protocol family 17 [ 1.670000] XScale DSP coprocessor detected. [ 1.680000] registered taskstats version 1 [ 1.680000] rtc-rs5c372 0-0032: setting system clock to 2012-07-13 16:50:50 UTC (1342198250) [ 1.700000] Initalizing network drop monitor service [ 1.700000] Freeing init memory: 112K Loading, please wait... [ 1.960000] udev[39]: starting version 164 [ 2.940000] SCSI subsystem initialized [ 3.230000] scsi0 : sata_vsc [ 3.240000] scsi1 : sata_vsc [ 3.240000] scsi2 : sata_vsc [ 3.250000] scsi3 : sata_vsc [ 3.250000] ata1: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060200 irq 29 [ 3.260000] ata2: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060400 irq 29 [ 3.270000] ata3: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060600 irq 29 [ 3.270000] ata4: SATA max UDMA/133 mmio m4096@0x80060000 port 0x80060800 irq 29 [ 3.640000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 3.670000] ata1.00: ATA-8: WDC WD5000AAKS-00UU3A0, 01.03B01, max UDMA/133 [ 3.670000] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 3.700000] ata1.00: configured for UDMA/133 [ 3.700000] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 01.0 PQ: 0 ANSI: 5 [ 4.060000] ata2: SATA link down (SStatus 0 SControl 300) [ 4.410000] ata3: SATA link down (SStatus 0 SControl 300) [ 4.760000] ata4: SATA link down (SStatus 0 SControl 300) [ 4.870000] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) [ 4.880000] sd 0:0:0:0: [sda] Write Protect is off [ 4.880000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.900000] sda: sda1 sda2 sda3 < sda5 > [ 4.950000] sd 0:0:0:0: [sda] Attached SCSI disk Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... Begin: Loading[ 5.750000] md: raid1 personality registered for level 1 Success: loaded module raid1. done. Begin: Assembling all MD arrays ... [ 5.800000] mdadm: sending ioctl 1261 to a partition! [ 5.810000] mdadm: sending ioctl 1261 to a partition! [ 5.810000] mdadm: sending ioctl 1261 to a partition! [ 5.820000] mdadm: sending ioctl 1261 to a partition! [ 5.820000] mdadm: sending ioctl 1261 to a partition! [ 5.830000] mdadm: sending ioctl 1261 to a partition! [ 5.840000] mdadm: sending ioctl 1261 to a partition! [ 5.840000] mdadm: sending ioctl 1261 to a partition! [ 5.850000] mdadm: sending ioctl 800c0910 to a partition! [ 5.850000] mdadm: sending ioctl 800c0910 to a partition! Failure: failed to assemble all arrays. done. done. Begin: Running /scripts/local-premount ... done. [ 6.320000] kjournald starting. Commit interval 5 seconds [ 6.330000] EXT3 FS on sda2, internal journal [ 6.340000] EXT3-fs: mounted filesystem with ordered data mode. Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting Using makefile-style concurrent boot in runlevel S. Starting the hotplug events dispatcher: udevd[ 8.050000] udev[151]: starting version 164 . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...[ 9.420000] Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI [ 9.420000] Copyright (c) 1999-2006 Intel Corporation. [ 9.800000] e1000: 0000:00:01.0: e1000_probe: (PCI:33MHz:32-bit) 00:02:41:00:94:7f [ 10.020000] usbcore: registered new interface driver usbfs [ 10.020000] usbcore: registered new interface driver hub [ 10.120000] usbcore: registered new device driver usb [ 10.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.390000] e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection [ 10.430000] ehci_hcd 0000:00:05.2: EHCI Host Controller [ 10.430000] ehci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 1 [ 10.450000] ehci_hcd 0000:00:05.2: Enabling legacy PCI PM [ 10.490000] ehci_hcd 0000:00:05.2: irq 27, io mem 0x80063000 [ 10.510000] ehci_hcd 0000:00:05.2: USB 2.0 started, EHCI 1.00 [ 10.510000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 10.520000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.530000] usb usb1: Product: EHCI Host Controller [ 10.530000] usb usb1: Manufacturer: Linux 2.6.32-5-iop32x ehci_hcd [ 10.540000] usb usb1: SerialNumber: 0000:00:05.2 [ 10.550000] usb usb1: configuration #1 chosen from 1 choice [ 10.550000] hub 1-0:1.0: USB hub found [ 10.560000] hub 1-0:1.0: 5 ports detected [ 10.750000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 10.770000] ohci_hcd 0000:00:05.0: OHCI Host Controller [ 10.770000] ohci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 2 [ 10.780000] ohci_hcd 0000:00:05.0: irq 30, io mem 0x80061000 [ 10.880000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.880000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.900000] usb usb2: Product: OHCI Host Controller [ 10.900000] usb usb2: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd [ 10.900000] usb usb2: SerialNumber: 0000:00:05.0 [ 10.930000] usb usb2: configuration #1 chosen from 1 choice [ 10.960000] hub 2-0:1.0: USB hub found [ 10.960000] hub 2-0:1.0: 3 ports detected [ 10.980000] ohci_hcd 0000:00:05.1: OHCI Host Controller [ 11.010000] ohci_hcd 0000:00:05.1: new USB bus registered, assigned bus number 3 [ 11.010000] ohci_hcd 0000:00:05.1: irq 29, io mem 0x80062000 [ 11.140000] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.140000] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.150000] usb usb3: Product: OHCI Host Controller [ 11.150000] usb usb3: Manufacturer: Linux 2.6.32-5-iop32x ohci_hcd [ 11.170000] usb usb3: SerialNumber: 0000:00:05.1 [ 11.180000] usb usb3: configuration #1 chosen from 1 choice [ 11.190000] hub 3-0:1.0: USB hub found [ 11.190000] hub 3-0:1.0: 2 ports detected done. Activating swap...[ 11.810000] Adding 748536k swap on /dev/sda5. Priority:-1 extents:1 across:748536k done. Checking root file system...fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda2: clean, 27294/30466048 files, 2115481/121846528 blocks done. [ 13.180000] EXT3 FS on sda2, internal journal [ 13.760000] loop: module loaded Cleaning up ifupdown.... Loading kernel modules...done. [ 13.990000] __ratelimit: 30 callbacks suppressed [ 14.000000] mdadm: sending ioctl 800c0910 to a partition! [ 14.000000] mdadm: sending ioctl 800c0910 to a partition! [ 14.030000] mdadm: sending ioctl 800c0910 to a partition! [ 14.030000] mdadm: sending ioctl 800c0910 to a partition! [ 14.050000] mdadm: sending ioctl 1261 to a partition! [ 14.050000] mdadm: sending ioctl 1261 to a partition! [ 14.080000] mdadm: sending ioctl 1261 to a partition! [ 14.090000] mdadm: sending ioctl 1261 to a partition! [ 14.100000] mdadm: sending ioctl 1261 to a partition! [ 14.100000] mdadm: sending ioctl 1261 to a partition! Generating udev events for MD arrays...done. Setting up networking.... Activating lvm and md swap...done. Checking file systems...fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 17/124496 files, 20609/248832 blocks done. Mounting local filesystems...done. Activating swapfile swap...done. Cleaning up temporary files.... Setting kernel variables ...done. Configuring network interfaces...done. Starting portmap daemon.... Starting NFS common utilities: statd. Cleaning up temporary files.... INIT: Entering runlevel: 2 [ 18.170000] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX Using makefile-style concurrent boot in runlevel 2. Starting portmap daemon...Already running.. Starting NFS common utilities: statd. [ 19.470000] RPC: Registered udp transport module. [ 19.470000] RPC: Registered tcp transport module. [ 19.480000] RPC: Registered tcp NFSv4.1 backchannel transport module. Starting enhanced syslogd: rsyslogd. [ 20.580000] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 22.320000] NET: Registered protocol family 10 [ 22.340000] svc: failed to register lockdv1 RPC service (errno 97). [ 22.400000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 22.430000] NFSD: starting 90-second grace period Starting Samba daemons: nmbd smbd. Exporting directories for NFS kernel daemon.... Starting NFS kernel daemon: nfsd mountd. Starting web server: apache2. Starting deferred execution scheduler: atd. Starting system message bus: dbus. Starting periodic command scheduler: cron. Starting MTA:Starting MD monitoring service: mdadm --monitor. Starting internet superserver: inetd. Starting OpenBSD Secure Shell server: sshd. Starting the Winbind daemon: winbind. exim4. Debian GNU/Linux 6.0 fsFreedom9 ttyS0 fsFreedom9 login: root Password: <<it knew my old password!!>> Last login: Fri Jul 13 12:38:13 EDT 2012 on ttyS0 Linux fsFreedom9 2.6.32-5-iop32x #1 Sun May 6 07:47:32 UTC 2012 armv5tel The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@fsFreedom9:~# pwd /root root@fsFreedom9:~# Best Regards Chris Wilkinson 301 277 2871 -- To UNSUBSCRIBE, email to debian-arm-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/000001cd6100$678758b0$36960a10$@net -- To UNSUBSCRIBE, email to debian-arm-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/002f01cd611a$2930a430$7b91ec90$@net
