Hi 1. I have been trying to load and boot Emdebian FS on the ARM board but when the ARM board boots into Emdebian, the /sbin folder does not exist, I just see sbin file of a size 0bytes.
I ran ./emsecondstage on my arm baord after doing tar -xzpf emdebian-arm.tgz next I created a jffs2 filesystem mkfs.jffs2 -e 0x20000 -s 0x800 -r /EmFS -o emrootfs.jffs2 -l -n -m none next it load it on mtdblock1 like this (my stsem looks for rootfs in mtdbl0ck1) cat emrootfs.jffs2 > /dev/mtdblock1 and i reboot the board. This is what happens: 2. My LCD display on the board also does not work once filesystem loads, was working earlier. Any help is appreciated. Thanks !! Starting kernel ... Uncompressing Linux............................................................. ...................................... done, booting the kernel. Linux version 2.6.24 (pvilc...@bendor) (gcc version 4.2.0 20070413 (prerelease) (CodeSourcery Sourcery G++ Lite 2007q1-10)) #1 Thu Jun 12 16:42:24 CEST 2008 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 Machine: Atmel AT91SAM9263-EK Ignoring unrecognised tag 0x54410008 Memory policy: ECC disabled, Data cache writeback Clocks: CPU 199 MHz, master 99 MHz, main 16.367 MHz CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: mem=64M console=ttyS0,115200 root=/dev/mtdblock1 mtdparts=a t91_nand:4M(mtdblock0),-(root) rw rootfstype=jffs2 AT91: 160 gpio irqs in 5 banks PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61696KB available (2804K code, 248K data, 120K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 64 bytes NET: Registered protocol family 16 AT91: Power Management AT91: Starting after user reset SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: pit clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) atmel_lcdfb atmel_lcdfb.0: 150KiB frame buffer at 23d40000 (mapped at ffc00000) Console: switching to colour frame buffer device 30x40 atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00700000 (mapped at c485c000), i rq 26 atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize loop: module loaded MACB_mii_bus: probed eth0: Atmel MACB at 0xfffbc000 irq 21 (3a:1f:34:08:54:54) eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:00, irq=-1) Driver 'sd' needs updating - please use bus_type methods NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit ) AT91 NAND: 8-bit, Software ECC Scanning device for bad blocks 2 cmdlinepart partitions found on MTD device at91_nand Creating 2 MTD partitions on "at91_nand": 0x00000000-0x00400000 : "mtdblock0" 0x00400000-0x10000000 : "root" atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14) usbmon: debugfs is not available at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: irq 29, io mem 0x00a00000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usb 1-1: new full speed USB device using at91_ohci and address 2 usb 1-1: configuration #1 chosen from 1 choice usb 1-2: new low speed USB device using at91_ohci and address 3 usb 1-2: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. udc: at91_udc version 3 May 2006 mice: PS/2 mouse device common for all mice input: gpio-keys as /class/input/input0 ads7846 spi0.3: touchscreen, irq 31 input: ADS784x Touchscreen as /class/input/input1 rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0 Registered led device: ds1 Registered led device: ds2 Registered led device: ds3 input: HID 04d9:1400 as /class/input/input2 input: USB HID v1.10 Keyboard [HID 04d9:1400] on usb-at91-2 input: HID 04d9:1400 as /class/input/input3 input: USB HID v1.10 Mouse [HID 04d9:1400] on usb-at91-2 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.15 (Tue Nov 20 19:16:42 200 7 UTC). AC97C regs = FFFA0000 AC97C irq = 18 at91-ac97: codec read timeout <4>at91-ac97: codec read timeout <4>at91-ac97: codec read timeout <4>at91-ac97: codec read timeout <6>ALSA device list: #0: Atmel AC97 Controller at 0xfffa0000, irq 18 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. rtc-at91sam9 at91_rtt.0: setting system clock to 2009-05-08 10:14:13 UTC (124177 7653) JFFS2 error: (1) jffs2_build_inode_pass1: child dir "apt" (ino #1979) of dir ino #1969 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "ldconfig" (ino #1980) of di r ino #1969 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "apt" (ino #1984) of dir ino #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "x11" (ino #1992) of dir ino #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "dpkg" (ino #1987) of dir in o #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "misc" (ino #1990) of dir in o #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "dhcp3" (ino #1986) of dir i no #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "urandom" (ino #1991) of dir ino #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "cdebconf" (ino #1985) of di r ino #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "initscripts" (ino #1988) of dir ino #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "libuuid" (ino #1989) of dir ino #1970 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "archives" (ino #1981) of di r ino #1979 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "partial" (ino #1982) of dir ino #1981 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "lists" (ino #1993) of dir i no #1984 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "periodic" (ino #1994) of di r ino #1984 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "questions" (ino #1999) of d ir ino #1985 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "templates" (ino #2001) of d ir ino #1985 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "info" (ino #2008) of dir in o #1987 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "triggers" (ino #2014) of di r ino #1987 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "alternatives" (ino #2004) o f dir ino #1987 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "parts" (ino #2010) of dir i no #1987 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "updates" (ino #2015) of dir ino #1987 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "partial" (ino #1997) of dir ino #1993 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "Kentucky" (ino #1555) of di r ino #1373 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "info" (ino #1582) of dir in o #1020 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "alternatives" (ino #1581) o f dir ino #1020 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "lists" (ino #1583) of dir i no #1020 appears to be a hard link scsi 0:0:0:0: Direct-Access USB Flash Memory 1.00 PQ: 0 ANSI: 2 VFS: Mounted root (jffs2 filesystem). Freeing init memory: 120K sd 0:0:0:0: [sda] 1967104 512-byte hardware sectors (1007 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Assuming drive cache: write through JFFS2 warning: (1) jffs2_do_read_inode_internal: Truncating ino #19 to 667784 by tes failed because it only had 0 bytes to start with! sd 0:0:0:0: [sda] 1967104 512-byte hardware sectors (1007 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 0:0:0:0: [sda] Attached SCSI removable disk /bin/sh: can't access tty; job control turned off / # JFFS2 warning: (327) jffs2_do_read_inode_internal: Truncating ino #635 to 95 40 bytes failed because it only had 12 bytes to start with! JFFS2 warning: (327) jffs2_do_read_inode_internal: Truncating ino #812 to 181464 bytes failed because it only had 40960 bytes to start with! JFFS2 warning: (327) jffs2_do_read_inode_internal: Truncating ino #883 to 435188 8 bytes failed because it only had 294067 bytes to start with! / # / # JFFS2 warning: (327) jffs2_do_read_inode_internal: Truncating ino #2246 to 3 1848 bytes failed because it only had 1936 bytes to start with! lJFFS2 warning: (327) jffs2_do_read_inode_internal: Truncating ino #883 to 43518 88 bytes failed because it only had 294067 bytes to start with! s bin media boot mnt datestring opt debootstrap proc dev root emdebian-archive-keyring.gpg sbin emdebian-arm.tgz selinux emsecondstage srv etc sys home tmp lib usr linuxrc var / # / #
