Installed kernel 2.6.14 from unstable, and solved. Now not load ide-scsi module and devices are hda and hdc.
Thanks all dclemen wrote: > Lee Begg wrote: > >>On Wed, 09 Nov 2005 00:16, dclemen wrote: >> >> >>>More info: dmesg >>> >>>Bootdata ok (command line is root=/dev/sda3 ro console=tty0 ) >> >><snip> >> >>>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >>>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx >>>JFS: nTxBlock = 8013, nTxLock = 64111 >>>Adding 1775172k swap on /dev/sda2. Priority:-1 extents:1 >>>Probing IDE interface ide0... >>>hda: TOSHIBA ODD-DVD SD-M1802, ATAPI CD/DVD-ROM drive >>>Probing IDE interface ide1... >>>hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive >>>Probing IDE interface ide2... >>>Probing IDE interface ide3... >>>Probing IDE interface ide4... >>>Probing IDE interface ide5... >>>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >>>ide1 at 0x170-0x177,0x376 on irq 15 >>>ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX >>>as device >> >> >>Since ide-scsi is not in your bootparams (the "command line" above), my guess >>is that you have ide-scsi in /etc/modules. If you do, remove it. Then >>reboot. >> >>If that isn't the case, did you compile your kernel? Maybe you turned > > ide-scsi > >>on? >> >>As of 2.6.0, noone should use ide-scsi (unless it doesn't work at all > > without > >>it). >> >>Hope this helps. >> >>Later >>Lee Begg > > > No I don't compile kernel, I get it as .deb package (2.6.12-1). > > ide-scsi are not in /etc/modules, but it is loaded (restart system but > loaded again). This is my modules file: > > $ cat /etc/modules > # /etc/modules: kernel modules to load at boot time. > # > # This file should contain the names of kernel modules that are > # to be loaded at boot time, one per line. Comments begin with > # a "#", and everything on the line after them are ignored. > > ide-cd > ide-disk > ide-generic > psmouse > sd_mod > > > When I try to remove this module I get this error > # rmmod ide-scsi > Terminado (killed) > > Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:32 2005 ... > localhost kernel: Oops: 0000 [1] > > Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:32 2005 ... > localhost kernel: CR2: 0000000000000370 > > Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:37 2005 ... > localhost kernel: Oops: 0000 [2] > > Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:37 2005 ... > localhost kernel: CR2: 0000000000000370 > > And module are not removed: > # lsmod | grep ide > ide_generic 1600 0 [permanent] > ide_disk 18048 0 > ide_cd 43552 0 > cdrom 39544 2 sr_mod,ide_cd > ide_scsi 18116 0 > ide_core 144888 5 amd74xx,ide_generic,ide_disk,ide_cd,ide_scsi > scsi_mod 151512 5 sg,sr_mod,ide_scsi,sd_mod,libata > > Maybe as Dean Hamstead said, I have to rebuild initrd? (remove/rename > /lib/modules/2.6.12-1-amd64-k8/kernel/drivers/scsi/ide-scsi.ko file, and > mkinitrd?) > > Thanks for replies!!! > > (I boot with old 2.6.8 kernel and not load ide-scsi module, devices are > hda and hdc and work fine) > > -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
