As has been presented to me, the following is an instruction set to generate the graphical representation of the New Age symbology. (Forthcoming Documentation)
The flat rendition is represented by convergent open crescents merging into a single transcendual point passing through three 3d interlocking rings (as 2d side view bands). The symbol is luminescent gold in color and the background of this symbol is an iridescent purple approximating 24bRGB:200x100x200 (of 255) or [RGB%:(100%x50% x100%) with Lux=(2/3)]. This symbol is most easily drawn on a 2d grid of 30x by 20y units, with numerical origin the bottom left. The following is a listing of arcs used in this representation, and below is an instruction set for manual drawing of this symbol. If drawn by hand, the following guides are suggested: (Attached example image) 1: Background: - Plane of 30 units wide and 20 high. (0,0 to 30x20) 2: Convergent Crescents: (Guides) - Circles of radius 4.0 -- Centered: 8,8 -- Centered: 20,8 -- Centered: 14,14 -- Centered: 14,0 - Circles of radius 6.0 -- Centered: 8,8 -- Centered: 20,8 - Lines from 14,18 to -- Endpoint: 12,8 -- Endpoint: 20,8 - Arc of radius 5.0 intersecting x=6 Centered: 8,8 (Guide) -- Circle of radius 1.0 Centered at this point - Arc of radius 5.0 intersecting x=22 Centered: 20,8 (Guide) -- Circle of radius 1.0 Centered at this point 3: Rings: (Guides) (in 3d, three intersecting regular torus' centered on 14,14,0 each IR:2.0 OR:4.0 or LR:3.0 AR:1.0; angle offset of 0 (horizontal), +180/5, (-180)/5 around Z axis) - Circles of radius 1.0 -- Centered: 11,14 (Leftmost Horizontal Ring) -- Centered: 17,14 (Rightmost Horizontal Ring) -- Arcs of radius 4.0 from 14,14 intersecting circles of radius 2.0 from above center points. (Guide for 4 additional circles of radius 1.0) -- Centered: [four circles at above intersection points.] (Each end of flat rotated torus) - Lines connecting outer diameter of each corresponding pair of above circles. Except for the lines formed representing each ring, all edge boundaries are non- intersecting of others and persist between each intersecting point. 4: Completion of Primary Symbol: (Note: Primary will never be shown without Rings completed.) Using the above guides, finalize the following: - Two lines radiating from point at 14,18 - major length of two circles intersecting the endpoints of these lines until intersection with edge of circles (r=1.0 centered: x=6 and x=22) - convex length of these circles r=1.0 at x=6 and x=22 until intersection with two circles (centered 8,8 and 20,8 r=3.0) - major length of these circles until edge intersection with circle centered at 14,0 - minor length of circle centered at 14,0 5: Completion of Rings: (Note: Primary will never be shown without Rings completed.) - Lines connecting outer diameter of corresponding circles in parallel - convex length of these circles between line endpoints Note: center point of all three oblong rings is at 14,14; these represent the 3 interlocking torus rings of the 3d representation. 6: Entity Indicator: The Entity Indicator is voluntarily used and is typically text (or limited design) along the rightmost edge of the field, of any coloration desired upon standard background, aligned vertically in the area bound by x=28 and x=30 (outer edge, without intersection) with all text read from y=0 upward. 7: Entity Logo or Seal: The Entity Seal location is also voluntary, but must be of the entity or organization in (6). Placement of any logo in this location indicates comprehensive support of New Age engagements and is positioned in a symbolic location relative to the Primary Symbol. - if round, Centered at 14,2 and of maximal radius 2.0 - other shapes: centered along x=14 below y=4 and NOT intersecting the Primary Symbol. - All designs must be between bounds x=10 and x=18 and lower edge of Primary Symbol without intersection, aligned to be viewed y=0 the lower edge. 8: Other Locations: No other location on this field is to be used for any design other than with the formal authority of the New Age; all remaining areas are reserved for specific indicators to be announced upon utilization. Note that this is a flat rendition of a 3d openspace object. 9: Flat Rendition Display Practices: - Mounted flat with point upward (or right-facing when against backdrop of speaker), never non-horizontal unless only one side is visible and used to represent the Entity within their environment. - Hung or draped as a flag, with x=0 as the connection point to mounting apparatus, connected to vertical mount allowing horizontal display if flat. - Edge decorations are desirable when used as a flag, standard gold tassel is recommended if no Entity is identified, or Entity-specific coloration and material/designs/objects unobtrusive or distracting from the Primary Symbol are desirable. More information on this representation is forthcoming, a best effort will be made to publicise information related to this topic in a comprehensive and timely manner. Contact: Wilfred L. Guerin [EMAIL PROTECTED]
