I think you have the following ports visible in your photo: H = Hot Potable Water out of Heater to your hot water taps. C = Cold Potable Water into heater from the potable water pump. D = Drain for emptying the Heater of Potable Water for winterizing. P1 = Pressure Release Valve for an over-pressure condition caused by the electric element sticking on and boiling the contents of the Heater.
If you also have in and out for Coolant so the engine can heat the water they must be out of sight on the rear? What Josh said about using the Pressure Relief Valve will bleed air our of the Potable Water section. It won't bleed the coolant loop from the engine. Ken H. On Thu, 16 May 2019 at 18:29, Bruce Whitmore via CnC-List < cnc-list@cnc-list.com> wrote: > Hello all, > > I think I probably have some air trapped in my hot water heater. I have > found some pretty cryptic instructions for the heater, but: > > a). They do not include a good drawing or explanation of how the hoses, > either fresh water or coolant should be connected (yes I have looked for > better online instructions to no avail) > b). They say "Bleed air from the entire coolant system for proper > operation of both engine and water heater", but don't give instructions as > to the best way to do it. > c). They do not include a listing of the what the stamped letters next to > the outlets mean. (the upper left in the photo is "H", bottom left is "D", > upper right is "P1" and lower right is "C" > > Here's a photo of the water heater: Attwood EHM6-SM Water Heater.j > <https://www.dropbox.com/s/zknhmh77qlh7ks6/Attwood%20EHM6-SM%20Water%20Heater.jpg?dl=0> > > The tube in the upper left feeds the boat with hot water. I think the > tube on the bottom with the valve on it comes from the engine hot water > feed. I turned off the valve, and the hot water continued to run, so it is > definitely not the fresh water supply line to the heater. And, having a > valve on the hot coolant input line would make sense. Therefore, am I > correct in thinking the pipe on the lower right would be the return coolant > line to the engine? > > Now for conundrum #2. > > Here's a photo of the hoses leading out of the engine. Hot water heater > hoses at engine.jpg. > <https://www.dropbox.com/s/24pbeb82hakwxvd/Hot%20water%20heater%20hoses%20at%20engine.jpg?dl=0> > Those hoses connect to the grey solid pipes shown in the previous picture, > somewhere under the floorboards where I can't see which is which. They > were disconnected, but filled with coolant when I got the boat, so I was > just guessing when I connected the hoses to the engine. In looking at the > Yanmar manual, it appears the red hose should be the suction side coming > from the water heater, and the black hose would be the pressure (hot) water > coming from the engine to the water heater. Am I correct? > > Any way about it, since the water going down to the heater must flow down > under the floorboards, up to the heater, then out of the heater and back > down under the floorboards, the water heater would be a prime spot for air > to get trapped. > > So, I am thinking I should ease off the connection coming off the lower > right side of the heater and apply pressure to the appropriate hose coming > off the engine, and see if I get any air out. Then, I want to ensure I am > connecting the correct hose to the right inlet/outlet point on the engine. > Does this make sense? > > Thanks for your insights! > > Bruce Whitmore > > (847) 404-5092 (mobile) > bwhitm...@sbcglobal.net > _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > >
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
