Why don't you just make 10 a little louder, make 10 the top number, make
that a little louder?
These go to 11.
/This is spinal tap./
Neil Gallagher
Weatherly 35-1
Glen Cove, NY
On 9/19/2017 6:14 PM, Edd Schillay via CnC-List wrote:
Glenn,
Honestly, the only thing I did was wiring -- a few were loose so I
stripped, cleaned and made better connections.
That's when the lights came on and the plate started getting cold. The
temp in the chest dropped 5 degrees in a half hour -- which leads me
to believe the compressor works.
The control, however, has a dial that won't turn, stuck on the highest
setting, 7. (Personally, I prefer my knobs go to 11 -- and extra
points to anyone who gets that reference.)
If it's really working again, I may just leave everything as-is
instead of shelling out big bucks for a new controller for a 27
year-old fridge.
In your case, to test it, look at the wiring diagram and see if you
can skip the controller and apply power directly to the compressor.
One manual I found talked about a jumper wire.
Hope you get cool results. Good luck.
All the best,
Edd
-----------------------------------
Edd M. Schillay
Captain of the Starship Enterprise
C&C 37+
Sail Number: NCC-1701-B
City Island, New York
-----------------------------------
914.774.9767 | Mobile
-----------------------------------
Sent via iPhone 7
iPhone. iTypos. iApologize
On Sep 19, 2017, at 5:42 PM, Glenn Gambel via CnC-List
<cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com>> wrote:
Edd or Tom,
How did you decide it was the controller and not the compressor? Is
there a way to test to determine if the current controller is bad? My
controller is a 102N3030 12V DC with a 15 amp fuse. I believe the
digital control that you found on line will work in my boat, but I
hate to spend $295 to find out it is not the controller but really the
compressor or something else.
Any suggestions would be appreciated.
Glenn Gambel
Wind N Spirits
C&C 36
------ Original Message ------
From: "Edd Schillay via CnC-List" <cnc-list@cnc-list.com
<mailto:cnc-list@cnc-list.com>>
To: cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com>
Cc: "Edd Schillay" <e...@schillay.com <mailto:e...@schillay.com>>
Sent: 9/18/2017 7:46:30 AM
Subject: Re: Stus-List Danfoss Compressor Controller
Tom,
Awesome! Thanks!
All the best,
Edd
-----------------------------------
Edd M. Schillay
Captain of the Starship Enterprise
C&C 37+
Sail Number: NCC-1701-B
City Island, New York
-----------------------------------
914.774.9767 | Mobile
-----------------------------------
Sent via iPhone 7
iPhone. iTypos. iApologize
On Sep 17, 2017, at 11:50 PM, Tom Buscaglia via CnC-List
<cnc-list@cnc-list.com <mailto:cnc-list@cnc-list.com>> wrote:
Edd
OK, I located the info. The deal is that it's not so much the
manufacturer, but the compressor. These Nova Kools have a Danfoss.
These 4-pin controllers work with them. It got the lead from the
folks at Sure Marine. They could not help due to the age of our
units. But they did some research and came up with these. Guess I
caught em on a good day!
Hi Tom,
The information David provided you is not completely accurate.
The 4-pin Danfoss was used by a bunch of companies.
it is definitely obsolete, but if you do a Google search, it appears
that a few people still have stock.
http://www.outbackmarine.com.au/null~1325
<http://www.outbackmarine.com.au/null%7E1325>
http://www.penguinfrigo.co.uk/shop/product/436/control-module-12v-dc4-pinfor-danfoss-bd3-earlier-compressors/
Kind regards,
Todd Glenn
*Sure Marine Service Inc.*
(206) 784-9903
(800) 562-7797
Fax (206) 784-0506
t...@suremarine.com <mailto:t...@suremarine.com>
They're the best.
Tom B
At 04:56 PM 9/17/2017, you wrote:
------------------------------
_______________________________________________
This list is supported by the generous donations of our members. If
you wish to make a contribution to offset our costs, please go to:
https://www.paypal.me/stumurray
All Contributions are greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you wish to
make a contribution to offset our costs, please go to:
https://www.paypal.me/stumurray
All Contributions are greatly appreciated!
_______________________________________________
This list is supported by the generous donations of our members. If you wish to
make a contribution to offset our costs, please go to:
https://www.paypal.me/stumurray
All Contributions are greatly appreciated!
