24STs their a little bit bigger. http://pages.ebay.com/motors/link/?nav=item.view&id=141748070949&alt=web On Sep 9, 2015 10:10 AM, "Kevin Driscoll via CnC-List" < cnc-list@cnc-list.com> wrote:
> I am still looking for a Barient 18 self tailer or similar, if anyone > knows of one. > > Kevin > > On Tue, Sep 8, 2015, 6:02 PM Paul Baker via CnC-List < > cnc-list@cnc-list.com> wrote: > >> I fitted them to my 24 and they worked fine, were a struggle to get on >> but that meant they never slipped. >> Cheers >> Paul >> >> ------------------------------ >> To: cnc-list@cnc-list.com >> Date: Tue, 8 Sep 2015 17:08:15 -0300 >> >> Subject: Re: Stus-List Barient ST 32's >> From: cnc-list@cnc-list.com >> CC: rtaill...@eastlink.ca >> >> >> I have them on my 25 and they work great. They came on a pair of Barient >> 18s that I traded for another pair of winches I had and some splicing jobs. >> >> I don’t know what size they are but they almost look a size too small for >> the winches, maybe that’s why I haven’t had the slippage problems that some >> people have had. There is no way I could get my normal sheets in the outer >> groove but my light air ones do fit. I use 5/16” sheets and the key is to >> get three full wraps on the winch then grind it in to jam the top wrap >> against the bottom of the Wincher, if I don’t do that the sheet will back >> off. I like them because you can take in the majority of the sheet before >> the load comes on then put on the third wrap and finish trimming in the >> sail with one hand, great for single handed sailing. I still have to deal >> with the sheet as it comes off the winch but I can crank it in a couple >> turns before it gets around to the front of the winch, if you have someone >> to tail this is a non-issue. >> >> >> >> >> >> Rick Taillieu >> >> Nemesis >> >> '75 C&C 25 #371 >> >> Shearwater Yacht Club >> >> Halifax, NS. >> >> >> >> >> >> >> >> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *Marek >> Dziedzic via CnC-List >> *Sent:* September-07-15 19:16 >> *To:* C&C List >> *Cc:* Marek Dziedzic >> *Subject:* Re: Stus-List Barient ST 32's >> >> >> >> I had them on my C&C 24 and I could not make them to work. I removed >> them. >> >> >> >> But ymmv. >> >> >> >> Marek >> >> >> >> >> >> >> >> Sent from my Samsung device over Bell's LTE network. >> >> >> >> -------- Original message -------- >> From: David Knecht via CnC-List <cnc-list@cnc-list.com> >> Date: 2015-09-07 18:07 (GMT-05:00) >> To: CnC CnC discussion list <cnc-list@cnc-list.com> >> Cc: David Knecht <davidakne...@gmail.com> >> Subject: Re: Stus-List Barient ST 32's >> >> What about $50 for Winchers ( >> http://www.defender.com/product3.jsp?path=-1%7C118%7C2358547%7C2358555&id=899493 >> <http://www.defender.com/product3.jsp?path=-1%7c118%7c2358547%7c2358555&id=899493>)? >> I am considering trying one for one of my cabin top small secondaries. I >> have read that they work. Dave >> >> >> >> Aries >> >> 1990 C&C 34+ >> >> New London, CT >> >> >> >> >> On Sep 7, 2015, at 5:05 PM, Dennis C. via CnC-List <cnc-list@cnc-list.com> >> wrote: >> >> >> >> Pairs of used self tailers on eBay go for $1000-1800 depending on size. >> (There's a pair of 60 ST's out there now for $1700.) >> >> Winchmates are ~$550 each. That's $1100 a pair. >> >> Good used non-self tailers sell for $300-800 on eBay depending on size >> and condition. >> >> I upgraded Touche's primary, secondary and cabin top winches from alloy >> to chrome bronze. Net cost for 2 Barlow 28's, 2 Barlow 26's and 2 >> stainless Barient 22's (all used non ST's) was around $600. Paid $1100 for >> the "new" ones and sold two pairs of the old ones on eBay for $500 and >> tossed a pair of 28's in the dumpster. >> >> >> >> Just saying.... >> >> Dennis C. >> >> >> >> On Mon, Sep 7, 2015 at 3:13 PM, Harry Hallgring via CnC-List < >> cnc-list@cnc-list.com> wrote: >> >> Bill, >> >> Yes, that is probably what I will do for my primaries. >> >> Harry >> >> Sent from my iPad >> >> >> On Sep 7, 2015, at 11:07 AM, Bill Coleman via CnC-List < >> cnc-list@cnc-list.com> wrote: >> >> These? >> >> >> >> http://www.winchmate.com/store.html >> >> >> >> >> >> >> >> Bill Coleman >> >> C&C 39 >> >> >> >> >> >> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> ------------------------------ >> >> No virus found in this message. >> Checked by AVG - www.avg.com >> Version: 2015.0.6125 / Virus Database: 4419/10600 - Release Date: 09/08/15 >> >> _______________________________________________ Email address: >> CnC-List@cnc-list.com To change your list preferences, including >> unsubscribing -- go to the bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
