Link works On Jul 7, 2015 11:39 AM, "Ken Heaton via CnC-List" <cnc-list@cnc-list.com> wrote:
> Let me know if this link works to a couple of photos: > > https://plus.google.com/photos/+KenHeaton/albums/6168788765520268033 > > There is normally also a small rod connecting the rudder position sensor > to the quadrant but it was removed before we took these photos. > > Ken H. > > On 7 July 2015 at 08:57, Gary Russell via CnC-List <cnc-list@cnc-list.com> > wrote: > >> Ken, >> Terrific! That would be very helpful. >> Gary >> >> ~~~~~~~_/)~~~~~~ >> >> >> On Tue, Jul 7, 2015 at 7:53 AM, Ken Heaton via CnC-List < >> cnc-list@cnc-list.com> wrote: >> >>> Mine is the same setup as Edd's. I'll look to see if I have photos this >>> evening. >>> >>> Ken Heaton & Anne Tobin >>> S/V Salazar - Can 54955 >>> C&C 37/40 XL - Hull # 67 >>> Cape Breton Island, Nova Scotia >>> >>> >>> On 7 July 2015 at 07:49, Edd Schillay via CnC-List < >>> cnc-list@cnc-list.com> wrote: >>> >>>> Gary, >>>> >>>> The Enterprise came with a Robertson autopilot installed. The ram is >>>> installed on a shelf inside the access area on the port side next to the >>>> helm seat and connects to the steering quadrant. >>>> >>>> I should be getting the boat back this week and I'll take some pictures >>>> for you. >>>> >>>> The Robertson still works, but eventually I'd like to upgrade to the >>>> Raymarine Evolution. >>>> >>>> >>>> All the best, >>>> >>>> Edd >>>> >>>> ------------------------------- >>>> Edd M. Schillay >>>> Starship Enterprise >>>> NCC-1701-B >>>> C&C 37+ | City Island, NY >>>> www.StarshipSailing.com >>>> ------------------------------- >>>> 914.332.4400 | Office >>>> 914.774.9767 | Mobile >>>> ------------------------------- >>>> Sent via iPhone 6 >>>> iPhone. iTypos. iApologize >>>> >>>> On Jul 7, 2015, at 6:02 AM, Gary Russell via CnC-List < >>>> cnc-list@cnc-list.com> wrote: >>>> >>>> I just bought a 37 Plus and want to install a below deck autopilot. >>>> Has anyone done this? I am interested in the details of how (and where) to >>>> mount the ram. Pictures would be wonderful. >>>> >>>> Thanks, >>>> Gary >>>> S/V High Maintenance >>>> 1990 C&C 37 Plus >>>> East Greenwich, RI, USA >>>> ~~~~~~~_/)~~~~~~ >>>> >>>> _______________________________________________ >>>> >>>> Email address: >>>> CnC-List@cnc-list.com >>>> To change your list preferences, including unsubscribing -- go to the >>>> bottom of page at: >>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>> >>>> >>>> _______________________________________________ >>>> >>>> Email address: >>>> CnC-List@cnc-list.com >>>> To change your list preferences, including unsubscribing -- go to the >>>> bottom of page at: >>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>> >>>> >>>> >>> >>> _______________________________________________ >>> >>> Email address: >>> CnC-List@cnc-list.com >>> To change your list preferences, including unsubscribing -- go to the >>> bottom of page at: >>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>> >>> >>> >> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
