Hi David, Congrats on getting the 34+. I've owned mine for 3 years and still think I could not have possibly gotten a better boat for what we do. The promise is that is gives you plentiful room and comfort at the marina / anchor and runs like a bat out of he$$ around the cans.. It does just that.
All your questions are really straightforward. Exhaust hose: I replaced mine last year, it's not that bad. Your idea of connecting the old one to the new one is excellent. I just wrestled my old one out and taped a fiberglass wiring rod to the new one to pull some / guide it. The trick is to remove all the aft stateroom cushions then remove the fuel tank access panel and the wooden blocks that are screwed / wedged-in securing the fuel tank and find a way to jack-up tank to facilitate threading the new hose in under it ( I used 2 x 2's) . The challenge to thread the new hose is to line it up between the exposed strut bolts. Stick to the original hose construction / diameter and you'll be fine. It's a bit of a sweaty wrestling match but you and 1 other guy should be able to knock it out in less than 1 hour. "Through-Hulls" None of what you mentioned is below the waterline at rest. They get dipped-in some when motoring or sailing in excess of 5 or so knots but that's nothing that the standard siphon loops can't handle. The 34+ is the last of the Canadian C&C's and after 35 + odd years of designing racer cruisers they had it down.. Rob Ball knew what he was doing. FYI, all through hulls on mine are Marelon. I close them all everytime I leave the boat and they works well, Also, there are no cockpit or deck scuppers on the boat. All cockpit /deck water simply flows out the stern / swim platform area in a modern open stern / sport boat style. On my boat there's a drain for the propane locker, also well designed. No need to seal / mess with it as propane is heavier than air and flows down the drain like water with its exit above the waterline at rest There's no quadrant well. On my boat The rudder shaft goes up to the quadrant that is mounted on top and flush with the cockpit sub-floor. All that is easily accessible by simply removing the triangular fiberglass cover. Feel free to PM me for more details on how to tune the boat / other questions of you want. -Francois Rivard 1990 34+ "Take Five" Lake Lanier, GA Subject: Re: Stus-List 34+ transom thru-hulls Message-ID: <snt152-w7315fc52d9f459dde543fda0...@phx.gbl> Content-Type: text/plain; charset="iso-8859-1" I said "appear" to be below the waterline because the boat's not in the water, isn't going in the water anytime soon, and I've never actually seen one of these in the water :) All four thru-hulls are under the transom counter and below the boot stripe as well as below the waterline as defined by the existing bottom paint, so I have to assume they are submerged with the boat floating level. Given their location in the bowels of the stern lazarettes, I know accessing them is a pain but I'm paranoid enough that I'd close them when I'm leaving the boat on her mooring and not returning for a span of days at a time. On second though, I'd have to leave the two small ones open because those are scuppers, so no sense in valves on them at all. Here's a pic of the two port side thru hulls, big one is the exhaust. 2 more on the stbd side in the same configuration. So I'm the proud new owner of a '90 34+, and the first project I bit off was replacement of the exhaust hose from the muffer back, including the thru-hull. First off, this is not going to be fun because the hose runs under the fuel tank and span of the cockpit under the water heater where it is completely inaccessible. I'm hoping I'll be able to pull the new hose through by clamping it to the old hose with a double-ended barb, but it seems like it's an awful tight fit under the tank. If anyone else has done this job and has any suggestions, I'm all ears. Second, the thru-hulls themselves. There are 4 thru-hulls just under the transom - the exhaust, the two drains for the propane tank & steering quadrant well, and the bilge pump. All 4 are plastic mushroom-head thru-hulls, and I want to replace at least the exhaust thru-hull with a new marelon one. Question: none of these thru-hulls have seacocks on them, which seems odd (and unwise) to me because they appear to be below the waterline. What are your thoughts on putting a marelon ball valve on the new thru hull while I'm at it? I'm tempted to replace all 4 of them with new thru-hull and valves. Am I just being paranoid? Thanks all. I'm thrilled to have this boat and I'm sure I'll be pestering the heck out of this board! -Dave 1990 C&C 34+ "Faith Anne"
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
