Hi Marek, Not sure if you remember me but we met back in the spring when we worked the launch crew at NSC.
I'll be installing new genoa tracks and rebed a few other bits of hardware and was considering ordering up some of this exact tape. I picked up a roll from the Chandlery earlier in the summer but it's not the good stuff. I'll take that roll off your hands; it should be just enough to do what I need to do. Are you going down to the club Thursday night by any chance? Sean On Mon, Sep 8, 2014 at 10:47 PM, Marek Dziedzic via CnC-List < cnc-list@cnc-list.com> wrote: > If you are looking for the source, here they are. I bought mine from > Compass > Marine. It seems that the other one can sell smaller quantities. > > There is a downside to it: if you want it shipped to Canada, the cost is > about the same as the tape (around $30). It is worth its while to order > more > (cost of shipping is the same) and share. > > Btw. I can share one roll at cost (and it is already on the Canadian side > of > the border). > > Btw2. No association with either of them, but supposedly this is the best > butyl tape around. > > Bed-It Tape - Compass Marine http://www.pbase.com/mainecruising/butyl_tape > > Bed-It Tape - Hamilton Marine > > http://store.hamiltonmarine.com/browse.cfm/butyl-tape-bed-it-1-2-x-50-roll-7 > 55207-/4,59595.html > > Marek > > -----Original Message----- > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jake > Brodersen via CnC-List > Sent: Monday, September 08, 2014 7:55 PM > To: mcrom...@bell.blackberry.net; cnc-list@cnc-list.com > Subject: Re: Stus-List Companionway hood > > Mike, > > I used butyl tape when I replaced my companionway hatch. It is foolproof > stuff to work with and seals great. > > Jake > > Jake Brodersen > “Midnight Mistress” > C&C 35 Mk-III > Hampton VA > > > > -----Original Message----- > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Michael > Crombie via CnC-List > Sent: Monday, September 08, 2014 10:41 AM > To: cnc-list@cnc-list.com > Subject: Stus-List Companionway hood > > > A couple of the screws are loose on my companionway hood, so I am planning > on removing it and giving it a good cleaning (and cleaning the gunk > underneath it). > > What type of sealant should i put into the screwholes when I put it back > on? > 4200? Silicon? Any advice would be appreciated. > > There seemed to be quite the debate a few years ago about whether to seal > the entire underside or not. Mine only appears to have sealant around the > screws and i don't have any leaks (at least not around the companionway!) , > so I'll probably stick with that method. > > Thanks, > > Mike > Atacama C&C 33 Mk II > Toronto > Sent wirelessly from my BlackBerry device on the Bell network. > Envoyé sans fil par mon terminal mobile BlackBerry sur le réseau de Bell. > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > >
_______________________________________________ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
