Jig-a-Loo is absolutely nothing like McLube and less than half the price. Jig-a-Loo is a silicone lubricant.
McLube is a Dry Lubricant. They behave very differently. "Sailkote is a high performance dry lubricant specifically designed for marine use. Sailkote is a translucent liquid that sprays or wipes on and completely dries in seconds. So, unlike oils, silicones, and waxes, it will never attract dirt, water and contaminants that eventually degrade lubrication performance." MSDS Sheets on both: http://www.jigaloo.com/us/pdf/US-JIG-A-LOO(JIGUSA701_JIGUSA1601&JIGUSA501)_EN.pdf http://www.hoister.com/uploadedFiles/Product_Support/PDF/ML1-ML2_Sailkote-Domestic-Aerosol_MSDS_Eng.PDF Ken H. On 25 March 2014 17:35, JOHN D IRVIN <john.ir...@rogers.com> wrote: > Jig-a-Loo is similar to McLube and less than half the price. > > *From:* Paul Fountain <paul.fount...@sympatico.ca> > *To:* cnc-list@cnc-list.com > *Sent:* Tuesday, March 25, 2014 2:17:29 PM > > *Subject:* Re: Stus-List 1986 33MKII > > Terry, > > I have a C&C 33-II 1985, and there is no plastic track on my mast where the > main hoists - it takes a flat slide, 7/8" wide, 1 1/2" long and 1/8" thick > the track sides are a bit wider than the thickness of the loop on the > slides. > > A strong track is on the wish list - but unfortunately not very close to > the > top, as the system works well except for the slides catching on the gate > where they are inserted into the mast - I need to redesign the gate. > > -----Original Message----- > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Terry > pearson > Sent: March 25, 2014 1:06 PM > To: cnc-list@cnc-list.com > Subject: Re: Stus-List 1986 33MKII > > Its not a strong track, i wish it were. it fits inside the internal grove > on > my mast, Ive searched the internet and have not been able to identify what > it is. its a white plastic liner that fits inside the internal mast groove. > Its is getting brittle and has broken off several times on the lower edge, > creating all kinds of problems. my groove is round yet has a flat groove on > the outer edge of the internal round groove, if that makes sense. I'm at > the > point now that I'm considering ordering several flat and round slugs to see > what fits. Dwight, I'm taking that your using flat slides, what does your > mast groove look like? > > Thanks, > Terry > On Mar 25, 2014, at 10:19 AM, dwight <dwight...@gmail.com> wrote: > > > Rick > > > > I can hoist the main sail on my 35 MKII to within at least 2 feet of > > the top without a winch or strong track. My main sail is equipped > > with polymer slides that measure 1.47" long by 0.87" wide by 0.31" > > thick, measured as carefully as I could with the sail rolled and pack > > in its bag and these work very well in the as manufactured aluminium > > track. I also have to deal with the added friction involved with > > leading the halyard through turning blocks to the cockpit. I can > > raise it all the way to the top without winch if I or someone else > > pulls the halyard where it exits the mast. I cleaned and sanded the > > track in the mast at the same time as I sanded my mast a few years > > back and I don't use any lubricant on the slides. The sail does not > > fall like the blade of a guillotine again because of friction on the > > halyard from the turning blocks but I consider that a good thing as it > > aids me in a controlled packing the sail without having to deal with > > all the sail laying on the deck to start with... I don't have lazy > > jacks or my Dutchman system installed and I usually end up packing my > > mainsail alone the way I like it done, hopefully training it to fall the > same way every time. Maybe I am just a very strong man for my age. > > > > -----Original Message----- > > From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of > > Rick Brass > > Sent: March 25, 2014 11:33 AM > > To: cnc-list@cnc-list.com > > Subject: Re: Stus-List 1986 33MKII > > > > Before you even think about removing the "slide" track, go on line and > > make sure it is not a Tides Marine Strong Track. > > > > If it is a strong track, it is one of the better upgrades that could > > have been done on your boat. Performance is far better than you will > > get from sail slugs in an internal track. I can hoist the main on my > > 38 to within about 2 feet of the top without putting the halyard on a > > winch. Sand if you let the halyard go, the sail comes down like the blade > of a guillotine. > > Periodic maintenance is to flush the rack with dish soap and fresh water. > > > > Rick Brass > > > > Sent from my iPad > > > >> On Mar 24, 2014, at 21:12, Terry pearson <tvpear...@mchsi.com> wrote: > >> > >> On my 33MKII mast, the previous owner placed a nylon (or > >> similar)slide in > > the mast track. I want to remove the "slide" track and go back to the > > original sail slides for this mast, but I cant seem to find anything > > telling me the proper size. the track appears to be able to > > accommodate either round slugs or flat slides.is this possible? I > > tried measuring the slide slot and it appears to be 15/16th wide flat > slide .can anyone confirm this? > >> > >> Thanks, > >> Confused:=) > >> > >> > >> _______________________________________________ > >> This List is provided by the C&C Photo Album > >> http://www.cncphotoalbum.com/CnC-List@cnc-list.com > > > > > _______________________________________________ > > This List is provided by the C&C Photo Album > > http://www.cncphotoalbum.com/CnC-List@cnc-list.com > > > > > > > _______________________________________________ > > This List is provided by the C&C Photo Album > > http://www.cncphotoalbum.com/CnC-List@cnc-list.com > > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com/ > > CnC-List@cnc-list.com > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com/ > CnC-List@cnc-list.com > > > > _______________________________________________ > This List is provided by the C&C Photo Album > http://www.cncphotoalbum.com > CnC-List@cnc-list.com > >
_______________________________________________ This List is provided by the C&C Photo Album http://www.cncphotoalbum.com CnC-List@cnc-list.com
