Hi All, I have bought a new CiscoASR1001. Just configured it as a PPPoE server with simplest configuration. My PPPoE client connects successfully, gets authenticated and gets the IP address. But packet are not forwarded if I try to ping internet or even the ASR from the PPPoE client.
The same configuration works fine on a Cisco IOS router, If I make it a PPPoE server. Do I need to enable something on my ASR1001? or am I using a wrong IOS version? Source of my configuration is http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bbdsl/configuration/xe-3s/asr1000/bba-xe-3s-asr1000-book/bba-pppoe-client-xe.html#GUID-91AF32F2-662D-4EF8-99DD-37C021637AE7 Device> *enable* Device# *configure terminal* Device(config)# *interface GigabitEthernet 0/0/0* Device(config-if)# *no ip address* Device(config-if)# *pppoe enable* Device(config-if)# *pppoe-client dial-pool-number 1* Device(config-if)# *no shutdown* Device(config-if)# *exit* Device(config)# *interface dialer 1* Device(config-if)# *mtu 1492* Device(config-if)# *ip address negotiated* Device(config-if)# *encapsulation ppp* Device(config-if)# *dialer pool 1* Device(config-if)# *ppp pap sent-username username1 password password1* Device(config-if)# *end* Example: Configuring PPPoE on IPv4 Example: Server Configuration Device> *enable* Device# *configure terminal* Device# *username username1 password password1* Device(config)# *bba-group pppoe bba1* Device(config-bba-group)# *virtual-template 1* Device(config-bba-group)# *exit* Device(config)# *interface loopback 1* Device(config-if)# *ip address 192.2.0.2 255.255.255.0* Device(config-if)# *exit* Device(config)# *interface GigabitEthernet 0/0/0* Device(config-if)# *no ip address* Device(config-if)# *negotiation auto* Device(config-if)# *pppoe enable group bba1* Device(config-if)# *no shutdown* Device(config-if)# *exit* Device(config)# *interface virtual-template 1* Device(config-if)# *description pppoe bba1* Device(config-if)# *mtu 1492* Device(config-if)# *ip unnumbered loopback 1* Device(config-if)# *peer default ip address pool pool1* Device(config-if)# *ppp authentication pap* Device(config-if)# *exit* Device(config)# *ip local pool pool1 192.2.0.1 192.2.0.10* Device(config)# *end* #show version Cisco IOS XE Software, Version 03.11.00.S - Standard Support Release Cisco IOS Software, ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.4(1)S, RELEASE SOFTWARE (fc2) ROM: IOS-XE ROMMON System image file is "bootflash:/asr1001-universalk9.03.11.00.S.154-1.S-std.bin" Last reload reason: Reload Command License Level: ipbase License Type: Default. No valid license found. Next reload license Level: ipbase cisco ASR1001 (1RU) processor with 6848982K/6147K bytes of memory. Processor board ID SSI181608S5 4 Gigabit Ethernet interfaces 32768K bytes of non-volatile configuration memory. 16777216K bytes of physical memory. 7741439K bytes of eUSB flash at bootflash:. 999424K bytes of USB flash at usb0:. Configuration register is 0x2102 Regards, *Ali Sumsam - *eintellego Networks Pty Ltd Senior Network Engineer [email protected] ; www.eintellegonetworks.com Phone: 1300 239 038; Cell +61 (0)450 609 592 ; skype://sumsam.ali80 facebook.com/eintellegonetworks ; <http://twitter.com/networkceoau> linkedin.com/in/alisumsam The Experts Who The Experts Call Juniper - Cisco - Cloud _______________________________________________ cisco-nsp mailing list [email protected] https://puck.nether.net/mailman/listinfo/cisco-nsp archive at http://puck.nether.net/pipermail/cisco-nsp/
