Hi,
I'm new in nexus world, i just test some switches and i have problem:
There is one switch 5548 with version 6.0(2)N1(2a). I try to make fcoe
conenction between xenserver 6.1 (port 1/25) and linux fcoe target (
centos, port 1/26).
In both servers i have card: Cisco Systems Inc VIC FCoE HBA (rev a2), on
centos (target side) all looks good but from xenserver i don't see any
traffic. In xencenter i see the cisco card connected but when try to
discover new storage, xencenter don't find anything.
thanks for any help or clue
regards,
Piotr
my config:
vlan 11
fcoe vsan 11
vsan database
vsan 11
interface vfc2
bind interface Ethernet1/25
no shutdown
interface vfc26
bind interface Ethernet1/26
no shutdown
vsan database
vsan 11 interface vfc2
vsan 11 interface vfc26
interface Ethernet1/25
switchport mode trunk
spanning-tree port type edge trunk
interface Ethernet1/26
switchport mode trunk
spanning-tree port type edge trunk
outputs:
show lldp neighbors
Capability codes:
(R) Router, (B) Bridge, (T) Telephone, (C) DOCSIS Cable Device
(W) WLAN Access Point, (P) Repeater, (S) Station, (O) Other
Device ID Local Intf Hold-time Capability Port ID
0018.8b9c.cfe6 mgmt0 120 g21
nexus-2 Eth1/1 120 B Eth1/1
nexus-2 Eth1/2 120 B Eth1/2
nexus-2 Eth1/3 120 B Eth1/3
nexus-2 Eth1/5 120 B Eth1/5
nexus-test2 Eth1/7 120 B Eth1/1
b0fa.eb72.7c06 Eth1/25 120 b0fa.eb72.7c0a
b0fa.eb72.7f3e Eth1/26 120 b0fa.eb72.7f42
show fcoe database
-------------------------------------------------------------------------------
INTERFACE FCID PORT NAME MAC ADDRESS
-------------------------------------------------------------------------------
vfc26 0x6a0000 20:00:b0:fa:eb:72:7f:41 b0:fa:eb:72:7f:41
Total number of flogi count from FCoE devices = 1.
VE Ports:
-------------------------------------------------------------------------------
INTERFACE MAC ADDRESS VSAN
-------------------------------------------------------------------------------
vfc1 54:7f:ee:8e:ad:0c 2
port 26, only target is ok:
show flogi database
--------------------------------------------------------------------------------
INTERFACE VSAN FCID PORT NAME NODE NAME
--------------------------------------------------------------------------------
vfc26 2 0x6a0000 20:00:b0:fa:eb:72:7f:41
10:00:b0:fa:eb:72:7f:41
but from xencenter side there is no traffic:
show interface vfc 2
vfc2 is trunking
Bound interface is Ethernet1/25
Hardware is Ethernet
Port WWN is 20:01:54:7f:ee:8e:ac:7f
Admin port mode is F, trunk mode is on
snmp link state traps are enabled
Port mode is TF
Port vsan is 11
Trunk vsans (admin allowed and active) (1-2,11)
Trunk vsans (up) ()
Trunk vsans (isolated) ()
Trunk vsans (initializing) (1-2,11)
1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
0 frames input, 0 bytes
0 discards, 0 errors
0 frames output, 0 bytes
0 discards, 0 errors
last clearing of "show interface" counters Sun Feb 21 11:15:15 2010
Interface last changed at Sun Feb 21 11:15:15 2010
_______________________________________________
cisco-nsp mailing list [email protected]
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
