ceph2 | SUCCESS | rc=0 >> ceph version 0.80.7 (6c0127fcb58008793d3c8b62d925bc91963672a3)
ceph3 | SUCCESS | rc=0 >> ceph version 0.80.7 (6c0127fcb58008793d3c8b62d925bc91963672a3) ceph4 | SUCCESS | rc=0 >> ceph version 0.80.7 (6c0127fcb58008793d3c8b62d925bc91963672a3) Yes, I thought that using sysvinit was strange too, but I didn’t know what to expect… Wonder where that went off the rails? > On Jul 16, 2016, at 3:45 AM, Wido den Hollander <w...@42on.com> wrote: > > >> Op 15 juli 2016 om 21:19 schreef Will Dennis <willard.den...@gmail.com>: >> >> >> Hi all, >> >> Background: Completely new to Ceph; trying it out on three VMs I have, >> following install instructions found at >> http://docs.ceph.com/docs/master/start/quick-ceph-deploy/ >> <http://docs.ceph.com/docs/master/start/quick-ceph-deploy/> >> >> I am at the point in the docs where it says to run 'ceph-deploy osd >> activate’ on the other two nodes from the first node. I try to do so, but >> get the following error: >> >> [root@ceph2 ~]# ceph-deploy osd activate ceph3:/dev/sdc ceph3:/dev/sdd >> ceph3:/dev/sde >> [ceph_deploy.conf][DEBUG ] found configuration file at: >> /root/.cephdeploy.conf >> [ceph_deploy.cli][INFO ] Invoked (1.5.25): /bin/ceph-deploy osd activate >> ceph3:/dev/sdc ceph3:/dev/sdd ceph3:/dev/sde >> [ceph_deploy.osd][DEBUG ] Activating cluster ceph disks ceph3:/dev/sdc: >> ceph3:/dev/sdd: ceph3:/dev/sde: >> [ceph3][DEBUG ] connected to host: ceph3 >> [ceph3][DEBUG ] detect platform information from remote host >> [ceph3][DEBUG ] detect machine type >> [ceph_deploy.osd][INFO ] Distro info: CentOS Linux 7.2.1511 Core >> [ceph_deploy.osd][DEBUG ] activating host ceph3 disk /dev/sdc >> [ceph_deploy.osd][DEBUG ] will use init type: sysvinit >> [ceph3][INFO ] Running command: ceph-disk -v activate --mark-init sysvinit >> --mount /dev/sdc >> [ceph3][WARNIN] INFO:ceph-disk:Running command: /sbin/blkid -p -s TYPE >> -ovalue -- /dev/sdc >> [ceph3][WARNIN] ceph-disk: Cannot discover filesystem type: device /dev/sdc: >> Line is truncated: >> [ceph3][ERROR ] RuntimeError: command returned non-zero exit status: 1 >> [ceph_deploy][ERROR ] RuntimeError: Failed to execute command: ceph-disk -v >> activate --mark-init sysvinit --mount /dev/sdc >> >> In some manual testing, I found that if I ran the listed command, indeed I >> got no output: >> [root@ceph2 ~]# ssh root@ceph4 /sbin/blkid -p -s TYPE -ovalue -- /dev/sdc >> [root@ceph2 ~]# >> >> Then tried taking away the ‘-s TYPE’ and ‘-ovalue' params, I got output as >> follows: >> [root@ceph2 ~]# ssh root@ceph4 /sbin/blkid -p -- /dev/sdc >> /dev/sdc: PTTYPE="gpt" >> [root@ceph2 ~]# >> >> So if I modified the original command, but set the ‘-s' param to use >> “PTTYPE” instead of “TYPE”, I get a valid response: >> [root@ceph2 ~]# ssh root@ceph4 /sbin/blkid -p -s PTTYPE -ovalue -- /dev/sdc >> gpt >> [root@ceph2 ~]# >> >> Is this a bug in ‘osd activate’ (at least on CentOS 7.2), or is there some >> way to specify the blkid parameter to use? >> > > Which version of Ceph are you testing with? > > I see 'will use init type: sysvinit' which is odd, since Ceph version Jewel > uses systemd. > > Wido > >> Thanks, >> Will_______________________________________________ >> ceph-users mailing list >> ceph-users@lists.ceph.com >> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com _______________________________________________ ceph-users mailing list ceph-users@lists.ceph.com http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
