I have not used ceph-deploy, but it should use ceph-disk for the OSD preparation. Ceph-disk creates GPT partitions with specific partition UUIDS for data and journals. When udev or init starts the OSD, or mounts it to a temp location reads the whoami file and the journal, then remounts it in the correct location. There is no need for fstab entries or the like. This allows you to easily move OSD disks between servers (if you take the journals with it). It's magic! But I think I just gave away the secret.
Robert LeBlanc Sent from a mobile device please excuse any typos. On May 7, 2015 5:16 AM, "Georgios Dimitrakakis" <gior...@acmac.uoc.gr> wrote: > Indeed it is not necessary to have any OSD entries in the Ceph.conf file > but what happens in the event of a disk failure resulting in changing the > mount device? > > For what I can see is that OSDs are mounted from entries in /etc/mtab (I > am on CentOS 6.6) > like this: > > /dev/sdj1 /var/lib/ceph/osd/ceph-8 xfs rw,noatime,inode64 0 0 > /dev/sdh1 /var/lib/ceph/osd/ceph-6 xfs rw,noatime,inode64 0 0 > /dev/sdg1 /var/lib/ceph/osd/ceph-5 xfs rw,noatime,inode64 0 0 > /dev/sde1 /var/lib/ceph/osd/ceph-3 xfs rw,noatime,inode64 0 0 > /dev/sdi1 /var/lib/ceph/osd/ceph-7 xfs rw,noatime,inode64 0 0 > /dev/sdf1 /var/lib/ceph/osd/ceph-4 xfs rw,noatime,inode64 0 0 > /dev/sdd1 /var/lib/ceph/osd/ceph-2 xfs rw,noatime,inode64 0 0 > /dev/sdk1 /var/lib/ceph/osd/ceph-9 xfs rw,noatime,inode64 0 0 > /dev/sdb1 /var/lib/ceph/osd/ceph-0 xfs rw,noatime,inode64 0 0 > /dev/sdc1 /var/lib/ceph/osd/ceph-1 xfs rw,noatime,inode64 0 0 > > > So in the event of a disk failure (e.g. disk SDH fails) then in the order > the next one will take its place meaning that > SDI will be seen as SDH upon next reboot thus it will be mounted as CEPH-6 > instead of CEPH-7 and so on...resulting in a problematic configuration (I > guess that lots of data will be start moving around, PGs will be misplaced > etc.) > > > Correct me if I am wrong but the proper way to mount them would be by > using the UUID of the partition. > > Is it OK if I change the entries in /etc/mtab using the UUID=xxxxxx > instead of /dev/sdX1?? > > Does CEPH try to mount them using a different config file and perhaps > exports the entries at boot in /etc/mtab (in the latter case no > modification in /etc/mtab will be taken into account)?? > > I have deployed the Ceph cluster using only the "ceph-deploy" command. Is > there a parameter that I 've missed that must be used during deployment in > order to specify the mount points using the UUIDs instead of the device > names? > > > Regards, > > > George > > > > > On Wed, 6 May 2015 22:36:14 -0600, Robert LeBlanc wrote: > >> We dont have OSD entries in our Ceph config. They are not needed if >> you dont have specific configs for different OSDs. >> >> Robert LeBlanc >> >> Sent from a mobile device please excuse any typos. >> On May 6, 2015 7:18 PM, "Florent MONTHEL" wrote: >> >> Hi teqm, >>> >>> Is it necessary to indicate in ceph.conf all OSD that we have in the >>> cluster ? >>> we have today reboot a cluster (5 nodes RHEL 6.5) and some OSD seem >>> to have change ID so crush map not mapped with the reality >>> Thanks >>> >>> FLORENT MONTHEL >>> _______________________________________________ >>> ceph-users mailing list >>> ceph-users@lists.ceph.com [1] >>> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com [2] >>> >> >> >> Links: >> ------ >> [1] mailto:ceph-users@lists.ceph.com >> [2] http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >> [3] mailto:florent.mont...@flox-arts.net >> > > _______________________________________________ > ceph-users mailing list > ceph-users@lists.ceph.com > http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >
_______________________________________________ ceph-users mailing list ceph-users@lists.ceph.com http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
