I do sometimes compile from source, but I tend to build and start my
clusters using the lower level commands. I'm not sure if ceph-deploy is
intended to be used with from-source builds (it may very well and I just
don't know).
Mark
On 06/16/2014 05:47 PM, Zhe Zhang wrote:
Thanks guys. This looks really helpful, but still I can't pass through the step "ceph-deploy mon
create-initial" in the Quick Start build. I saw a line in the log file it's trying to run command
"sudo initctl emit ceph-mon cluster=ceph id=v3", and the monitor did not been started. Instead, I
used "sudo ceph-mon -i v3" to start the monitor,
[v3][DEBUG ] locating the `service` executable...
[v3][INFO ] Running command: sudo initctl emit ceph-mon cluster=ceph id=v3
[v3][INFO ] Running command: sudo ceph --cluster=ceph --admin-daemon
/var/run/ceph/ceph-mon.v3.asok mon_status
[v3][ERROR ] admin_socket: exception getting command descriptions: [Errno 2] No
such file or directory
[v3][WARNIN] monitor: mon.v3, might not be running yet
[v3][INFO ] Running command: sudo ceph --cluster=ceph --admin-daemon
/var/run/ceph/ceph-mon.v3.asok mon_status
[v3][ERROR ] admin_socket: exception getting command descriptions: [Errno 2] No
such file or directory
[v3][WARNIN] monitor v3 does not exist in monmap
[ceph_deploy.mon][INFO ] processing monitor mon.v3
[v3][DEBUG ] connected to host: v3
[v3][INFO ] Running command: sudo ceph --cluster=ceph --admin-daemon
/var/run/ceph/ceph-mon.v3.asok mon_status
[v3][ERROR ] admin_socket: exception getting command descriptions: [Errno 2] No
such file or directory
[ceph_deploy.mon][WARNIN] mon.v3 monitor is not yet in quorum, tries left: 5
[ceph_deploy.mon][WARNIN] waiting 5 seconds before retrying
...
, and then I created keys by "sudo ceph-create-keys -i v3". It seemed monitor was created
successfully. I continued to create /var/local/osd0 and /var/local/osd1 as my OSDs, and run "ceph-deploy
osd prepare v3:/var/local/osd0 v3:/var/local/osd1", this step was also fine. But when I tried to
activate OSDs with "ceph-deploy osd activate v3:/var/local/osd0 v3:/var/local/osd1", it failed, and
I saw those two osd0 and osd1 marked as down and out.
I am trying to use "sudo ceph-osd -n osd.0" "sudo ceph-osd -n osd.1" and I saw those two osds are marked as
up and in. But when I run "ceph health", it shows that the system is in "creating" state, not
"clean+active".
I am really confused with ceph-deploy, what it did for me? If I want to set up
ceph without it, what are the normal steps I need to walk through? I tried to
follow Installation(Manual) in the document. But I can't fully understand what
does in fact happen there. Any helps are really appreciated!
Zhe
-----Original Message-----
From: Mark Kirkwood [mailto:mark.kirkw...@catalyst.net.nz]
Sent: Friday, June 13, 2014 10:30 PM
To: Gregory Farnum; Zhe Zhang
Cc: ceph-users@lists.ceph.com
Subject: Re: [ceph-users] Run ceph from source code
I compile and run from the src build quite often. Here is my recipe:
$ ./autogen.sh
$ ./configure --prefix=/usr --sysconfdir=/etc --localstatedir=/var
--with-radosgw $ time make $ sudo make install $ sudo cp src/init-ceph
/etc/init.d/ceph $ sudo cp src/init-radosgw /etc/init.d/radosgw $ sudo chmod
755 /etc/init.d/radosgw $ sudo cp src/upstart/* /etc/init $ sudo cp udev/*
/lib/udev/rules.d/
Regards
Mark
On 14/06/14 10:07, Gregory Farnum wrote:
I don't know anybody who makes much use of "make install", so it's
probably not putting the init system scripts into place. So make sure
they aren't there, copy them from the source tree, and try again?
Patches to fix are welcome! :)
-Greg
Software Engineer #42 @ http://inktank.com | http://ceph.com
On Fri, Jun 13, 2014 at 1:41 PM, Zhe Zhang <zhe_zh...@symantec.com> wrote:
Hello, there,
I am trying to run ceph from source code. configure, make and make
install worked fine. But after done these steps, I can't see the
binary files in /etc/init.d/. My current OS is Centos6.5. I also
tried Ubuntu 12.04, the same issue occurred which said "unknown job
ceph..." when I tried to use upstart to run monitors and osds. How should I
start ceph with source code?
basically I hope I could modified the code and run it from there.
Zhe
_______________________________________________
ceph-users mailing list
ceph-users@lists.ceph.com
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
_______________________________________________
ceph-users mailing list
ceph-users@lists.ceph.com
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
_______________________________________________
ceph-users mailing list
ceph-users@lists.ceph.com
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
_______________________________________________
ceph-users mailing list
ceph-users@lists.ceph.com
http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
