Are you thinking it might be a permutation of: https://tracker.ceph.com/issues/53729 ? There are some posts in it to check for the issue, #53 and #65 had a few potential ways to check.
On Fri, Jun 10, 2022 at 5:32 AM Marius Leustean <marius.l...@gmail.com> wrote: > Did you check the mempools? > > ceph daemon osd.X dump_mempools > > This will tell you how much memory is consumed by different components of > the OSD. > Finger in the air, your ram might be consumed by the pg_log. > > If osd_pglog from the dump_mempools output is big, then you can lower the > values of the related configuration options: > > osd_min_pg_log_entries = 100 (default is 250) > osd_max_pg_log_entries = 500 (default is 10000) > osd_target_pg_log_entries_per_osd = 30000 (default is 300000) > > Those are just examples. You can adjust it based on your current memory > consumption and the available amount of RAM. > > On Fri, Jun 10, 2022 at 1:21 PM Eugen Block <ebl...@nde.ag> wrote: > > > Hi, > > > > could you share more cluster details and what your workload is? > > > > ceph -s > > ceph osd df tree > > ceph orch ls > > ceph osd pools ls detail > > > > How big are your PGs? > > > > Zitat von Mara Sophie Grosch <little...@lf-net.org>: > > > > > Hi, > > > > > > good catch with the way too low memory target, I wanted to configure 1 > > > GiB not 1 MiB. I'm aware it's low, but removed anyway for testing - it > > > sadly didn't change anything. > > > > > > I customize the config mostly for dealing problems I have, something in > > > my setup makes the OSDs eat lots of memory in normal operation, just > > > gradually increasing .. I'd send metrics if my monitoring was up again > > > ^^' That maybe being some form of cache was the reason for that config > > > line (it does not seem to be cache). > > > > > > I have found a way to deal with my cluster, using ceph-objectstore-tool > > > to export-remove all PGs from the OSDs, getting them online and happy > > > again and then importing a few PGs at a time in one OSD and let it > > > backfill to the others. > > > > > > The problem of eating very much memory on startup manifests with some > of > > > the PGs only, but for those it goes up to ~50GiB. Problematic: when it > > > has multiple of those PGs in its storage, it's handling those in > > > parallel - needing even more memory of course, until it finally gets > > > OOM-killed. > > > > > > So.. seems I can get my cluster running again, only limited by my > > > internet upload now. Any hints why it eats a lot of memory in normal > > > operation would still be appreciated. > > > > > > Best, Mara > > > > > > > > > Am Wed, Jun 08, 2022 at 09:05:52AM +0000 schrieb Eugen Block: > > >> It's even worse, you only give them 1MB, not GB. > > >> > > >> Zitat von Eugen Block <ebl...@nde.ag>: > > >> > > >>> Hi, > > >>> > > >>> is there any reason you use custom configs? Most of the defaults > > >>> work well. But you only give your OSDs 1 GB of memory, that is way > > >>> too low except for an idle cluster without much data. I recommend > > >>> to remove the line > > >>> > > >>> osd_memory_target = 1048576 > > >>> > > >>> and let ceph handle it. I didn't install Quincy yet but in a > > >>> healthy cluster the OSDs will take around 3 GB of memory, maybe 4, > > >>> so you should be good with your setup. > > >>> > > >>> Regards, > > >>> Eugen > > >>> > > >>> Zitat von Mara Sophie Grosch <little...@lf-net.org>: > > >>> > > >>>> Hi, > > >>>> > > >>>> I have a currently-down ceph cluster > > >>>> * v17.2.0 / quay.io/v17.2.0-20220420 > > >>>> * 3 nodes, 4 OSDs > > >>>> * around 1TiB used/3TiB total > > >>>> * probably enough resources > > >>>> - two of those nodes have 64GiB memory, the third has 16GiB > > >>>> - one of the 64GiB nodes runs two OSDs, as it's a physical node with > > >>>> 2 NVMe drives > > >>>> * provisioned via Rook and running in my Kubernetes cluster > > >>>> > > >>>> After some upgrades yesterday (system packages on the nodes) and > today > > >>>> (Kubernetes to latest version), I wanted to reboot my nodes. The > drain > > >>>> of the first node put a lot of stress on the other OSDs, making them > > go > > >>>> OOM - but I think that probably is a bug already, as at least one of > > >>>> those nodes has enough resources (64GiB memory, physical machine, > > ~40GiB > > >>>> surely free - but don't have metrics rn as everything is down). > > >>>> > > >>>> I'm now seeing all OSDs going into OOM right on startup, from what > it > > >>>> looks like everything is fine until right after `load_pgs` - as soon > > as > > >>>> it activates some PGs, memory usage increases _a lot_ (from ~4-5GiB > > >>>> RES before to .. 60GiB, though that depends on the free memory on > the > > >>>> node). > > >>>> > > >>>> Because of this, I cannot get any of them online again and need > advice > > >>>> what to do and what info might be useful. Logs of one of those OSDs > > are > > >>>> here[1] (captured via kubectl logs, so something right from start > > might > > >>>> be missing - happy to dig deeper if you need more) and my changed > > >>>> ceph.conf entries are here[2]. I had `bluefs_buffered_io = false` > > until > > >>>> today, changed it to true based on a suggestion in another debug > > >>>> thread[3] > > >>>> > > >>>> Any hint is greatly appreciated, many thanks > > >>>> Mara Grosch > > >>>> > > >>>> [1] https://pastebin.com/VFczNqUk > > >>>> [2] https://pastebin.com/QXust5XD > > >>>> [3] > > >>>> > > > https://lists.ceph.io/hyperkitty/list/ceph-users@ceph.io/message/CBPXLPWEVZLZE55WAQSMB7KSIQPV5I76/ > > >> > > >> > > >> > > > > > > > > _______________________________________________ > > ceph-users mailing list -- ceph-users@ceph.io > > To unsubscribe send an email to ceph-users-le...@ceph.io > > > _______________________________________________ > ceph-users mailing list -- ceph-users@ceph.io > To unsubscribe send an email to ceph-users-le...@ceph.io > _______________________________________________ ceph-users mailing list -- ceph-users@ceph.io To unsubscribe send an email to ceph-users-le...@ceph.io
