The original poster said the SVIs were "up" which they would not be if the VLANs didn't exist. The SVI would be "down/down" if the VLAN it's tied to doesn't exist on that device.
Further, if those switches are not in VTP transparent/off mode, you wouldn't see the VLANs in the running config. While a switch will usually create the VLAN when it's assigned as an access VLAN to a port, I've found switchports in routers typically do *not* do this, so it is possible to assign a VLAN to a port and create the SVI but not have the VLAN exist, but then the SVI should be "down/down." A "show vlan brief" would verify the existence of the VLANs on all devices. The OP's topic was "STP issues" and yet there's no "show spanning" output for any of the devices so no way to know whether STP is actually at issue here. For the OP, I would respectfully point out that if you are, in fact, a "bloody newbie" to networking, that perhaps pursuing the CCNA and CCNP curriculum might not be a better path than trying to jump right in to CCIE. Frankly, if you're struggling on Vol 1, Lab 1, on a task related to getting a couple VLANs instantiated, you're going to have a *very* difficult time preparing for the full exam. Best Regards, Bob CCIE #38296 On Tue, May 28, 2013 at 9:20 AM, Abdul s <[email protected]> wrote: > Hello , > > You have no vlans configured in VLAN database , so it is not up try this . > > conf t > > vlan 12,40,100,200,300,567 > > > interface Vlan12 > > ip address 150.100.12.14 255.255.255.0 > > ! > > interface Vlan40 > > ip address 150.100.40.14 255.255.255.0 > > ! > > interface Vlan100 > > ip address 100.100.100.14 255.255.255.0 > > ! > > interface Vlan200 > > ip address 100.100.200.14 255.255.255.0 > > ! > > interface Vlan300 > > ip address 100.100.250.14 255.255.255.0 > > ! > > interface Vlan567 > > ip address 150.100.220.14 255.255.255.240 > > > Let me know if it works !! > > > On Tue, May 28, 2013 at 2:28 PM, <[email protected] > >wrote: > > > [image: Boxbe] <https://www.boxbe.com/overview> > > [email protected] is not on your Guest List< > https://www.boxbe.com/approved-list?tc_serial=14245005325&tc_rand=2144170181&utm_source=stf&utm_medium=email&utm_campaign=ANNO_MWTP&utm_content=001&token=89ZYfyOjR3VmthosLAmMh5sSEyTAYNsxEZZscUe%2BVNleZfVOry4ZZA3AAduARcFN&key=SULXMqkWWY%2BwgJHwWXDkq7Cc%2F7bsnJZ08jqCqMkDFzI%3D>| > Approve > > sender< > https://www.boxbe.com/anno?tc_serial=14245005325&tc_rand=2144170181&utm_source=stf&utm_medium=email&utm_campaign=ANNO_MWTP&utm_content=001&token=89ZYfyOjR3VmthosLAmMh5sSEyTAYNsxEZZscUe%2BVNleZfVOry4ZZA3AAduARcFN&key=SULXMqkWWY%2BwgJHwWXDkq7Cc%2F7bsnJZ08jqCqMkDFzI%3D>| > Approve > > domain< > https://www.boxbe.com/anno?tc_serial=14245005325&tc_rand=2144170181&utm_source=stf&utm_medium=email&utm_campaign=ANNO_MWTP&utm_content=001&dom&token=89ZYfyOjR3VmthosLAmMh5sSEyTAYNsxEZZscUe%2BVNleZfVOry4ZZA3AAduARcFN&key=SULXMqkWWY%2BwgJHwWXDkq7Cc%2F7bsnJZ08jqCqMkDFzI%3D > > > > > > Send CCIE_RS mailing list submissions to > > [email protected] > > > > To subscribe or unsubscribe via the World Wide Web, visit > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > or, via email, send a message with subject or body 'help' to > > [email protected] > > > > You can reach the person managing the list at > > [email protected] > > > > When replying, please edit your Subject line so it is more specific > > than "Re: Contents of CCIE_RS digest..." > > > > > > Today's Topics: > > > > 1. Re: CCIE_RS Digest, Vol 88, Issue 24 (Joe Schulte) > > > > > > ---------------------------------------------------------------------- > > > > Message: 1 > > Date: Tue, 28 May 2013 06:27:59 -0500 > > From: Joe Schulte <[email protected]> > > To: "[email protected]" <[email protected]> > > Subject: Re: [OSL | CCIE_RS] CCIE_RS Digest, Vol 88, Issue 24 > > Message-ID: <[email protected]> > > Content-Type: text/plain; charset=us-ascii > > > > I am not up on specific tasks in the labs but I will say that I tried the > > GNS3 route and its got many flaws, most particularly the ESW- 16. > > > > My own advice would be to gloss over the layer 2 stuff until you can get > > hold of a physical rack. > > > > Speaking of, I'm up to my eyeballs in 3550 switches but have no 3560. If > > anyone would like to make a deal for one drop me a line. > > > > Sent from themy iPhone > > > > On May 28, 2013, at 3:00 AM, [email protected] wrote: > > > > > Send CCIE_RS mailing list submissions to > > > [email protected] > > > > > > To subscribe or unsubscribe via the World Wide Web, visit > > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > > > or, via email, send a message with subject or body 'help' to > > > [email protected] > > > > > > You can reach the person managing the list at > > > [email protected] > > > > > > When replying, please edit your Subject line so it is more specific > > > than "Re: Contents of CCIE_RS digest..." > > > > > > > > > Today's Topics: > > > > > > 1. STP issues (freda williams) > > > > > > > > > ---------------------------------------------------------------------- > > > > > > Message: 1 > > > Date: Tue, 28 May 2013 09:00:19 +0100 > > > From: freda williams <[email protected]> > > > To: CCIE_RS OnlineStudyList <[email protected]> > > > Subject: [OSL | CCIE_RS] STP issues > > > Message-ID: > > > <cajvfe_wb5efiodewkjj3ek4bvjeq8q+blxu8dgypaqr5avk...@mail.gmail.com > > > > > Content-Type: text/plain; charset=ISO-8859-1 > > > > > > Good day All, > > > > > > Am a just starting my journey towards my CCIE. Am a bloody newbie, I > will > > > appreciate your help with the following issues. > > > > > > Am of the mind that I have skipped a process/overlooking a requirement. > > > > > > Am runing GNS and have checke that the features run on the NM-16ESW > > > platform that I have but am still not able to do the tasks required in > > the > > > IPEXPERT Vol 1 Lab 1. > > > > > > Issue 1: > > > The hosts namely R1 to BB1 (VLAN 100 switches 1 & 2) and R5 to R6 & R7 > > > (VLAN 567 switches 1 & 2( Vlan 2567 switches 3 & 4) are not reachable > > > (I cannot ping or traceroute to them). The Vlans are connected across > > > switches. > > > > > > Issue 2: > > > After the creation of SVI's on Cats 1,2,3 & 4 they (SVI's)are up but > not > > > reachable from any point in the various subnets. > > > > > > I have attached the configurations of the affected systems below. > > > > > > Thanks in anticipation of your kind assistance. > > > > > > William Alfreds > > > > > > > > > > > > > > > ................................ > > > > > > > > > Cat1 > > > > > > Connected to Dynamips VM "Cat1" (ID 13, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > Cat1(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 4392 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname Cat1 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Port-channel2 > > > switchport mode trunk > > > ! > > > interface Port-channel3 > > > switchport mode trunk > > > ! > > > interface Port-channel4 > > > switchport mode trunk > > > ! > > > interface FastEthernet0/0 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet0/1 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet1/0 > > > switchport access vlan 12 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/1 > > > switchport access vlan 12 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/2 > > > switchport access vlan 12 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/3 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/4 > > > switchport access vlan 40 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/5 > > > switchport access vlan 567 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/6 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/7 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/8 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/9 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/10 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/11 > > > switchport access vlan 100 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/12 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/13 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/14 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/15 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/0 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/1 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/2 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/3 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/4 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/5 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/6 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/7 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/8 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/9 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 4 mode on > > > ! > > > interface FastEthernet2/10 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 4 mode on > > > ! > > > interface FastEthernet2/11 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 3 mode on > > > ! > > > interface FastEthernet2/12 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 3 mode on > > > ! > > > interface FastEthernet2/13 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/14 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/15 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface Vlan1 > > > no ip address > > > ! > > > interface Vlan12 > > > ip address 150.100.12.11 255.255.255.0 > > > ! > > > interface Vlan40 > > > ip address 150.100.40.11 255.255.255.0 > > > ! > > > interface Vlan100 > > > ip address 100.100.100.11 255.255.255.0 > > > ! > > > interface Vlan200 > > > ip address 100.100.200.11 255.255.255.0 > > > ! > > > interface Vlan300 > > > ip address 100.100.250.11 255.255.255.0 > > > ! > > > interface Vlan567 > > > ip address 150.100.220.11 255.255.255.240 > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 060F1F24545E0C0B11 > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 020F145E13160A3358 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > Cat1(config-if)# > > > > > > ................................ > > > > > > > > > Cat2 > > > > > > > > > Connected to Dynamips VM "Cat2" (ID 14, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > Cat2#do sh run > > > ^ > > > % Invalid input detected at '^' marker. > > > > > > Cat2#sh run > > > Building configuration... > > > > > > Current configuration : 4473 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname Cat2 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Port-channel1 > > > switchport mode trunk > > > ! > > > interface Port-channel4 > > > switchport mode trunk > > > ! > > > interface Port-channel3 > > > switchport mode trunk > > > ! > > > interface FastEthernet0/0 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet0/1 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet1/0 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/1 > > > switchport access vlan 100 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/2 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/3 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/4 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/5 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/6 > > > switchport access vlan 567 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/7 > > > switchport access vlan 567 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/8 > > > switchport access vlan 200 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/9 > > > switchport access vlan 300 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/10 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/11 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/12 > > > switchport access vlan 200 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/13 > > > switchport access vlan 300 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/14 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/15 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/0 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/1 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/2 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/3 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/4 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/5 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/6 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/7 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/8 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/9 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 3 mode on > > > ! > > > interface FastEthernet2/10 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 3 mode on > > > ! > > > interface FastEthernet2/11 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 4 mode on > > > ! > > > interface FastEthernet2/12 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 4 mode on > > > ! > > > interface FastEthernet2/13 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/14 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/15 > > > switchport mode trunk > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface Vlan1 > > > no ip address > > > ! > > > interface Vlan12 > > > ip address 150.100.12.12 255.255.255.0 > > > ! > > > interface Vlan40 > > > ip address 150.100.40.12 255.255.255.0 > > > ! > > > interface Vlan100 > > > ip address 100.100.100.12 255.255.255.0 > > > ! > > > interface Vlan200 > > > ip address 100.100.200.12 255.255.255.0 > > > ! > > > interface Vlan300 > > > ip address 100.100.250.12 255.255.255.0 > > > ! > > > interface Vlan567 > > > ip address 150.100.220.12 255.255.255.240 > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 000D03031C4B0E141B > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 011A1601431B031D35 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > Cat2# > > > .................................. > > > > > > Cat3 > > > > > > Connected to Dynamips VM "Cat3" (ID 6, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > Cat3(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 4001 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname Cat3 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > vtp domain ipexpert > > > vtp mode transparent > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > vlan 12 > > > name VLANB > > > ! > > > vlan 40 > > > name VLANC > > > ! > > > vlan 100 > > > name VLANA > > > ! > > > vlan 200 > > > name VLANE > > > ! > > > vlan 240 > > > ! > > > vlan 300 > > > name VLANF > > > ! > > > vlan 567 > > > name VLAND > > > ! > > > vlan 2200,2300,2567 > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Port-channel4 > > > switchport mode trunk > > > ! > > > interface Port-channel1 > > > switchport mode trunk > > > ! > > > interface Port-channel2 > > > switchport mode trunk > > > ! > > > interface FastEthernet0/0 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet0/1 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet1/0 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/1 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/2 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/3 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/4 > > > switchport access vlan 240 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/5 > > > switchport access vlan 2567 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/6 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/7 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/8 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/9 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/10 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/11 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/12 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/13 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/14 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/15 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/0 > > > ! > > > interface FastEthernet2/1 > > > ! > > > interface FastEthernet2/2 > > > ! > > > interface FastEthernet2/3 > > > ! > > > interface FastEthernet2/4 > > > ! > > > interface FastEthernet2/5 > > > ! > > > interface FastEthernet2/6 > > > ! > > > interface FastEthernet2/7 > > > ! > > > interface FastEthernet2/8 > > > ! > > > interface FastEthernet2/9 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/10 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/11 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/12 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/13 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 4 mode on > > > ! > > > interface FastEthernet2/14 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 4 mode on > > > ! > > > interface FastEthernet2/15 > > > ! > > > interface Vlan1 > > > no ip address > > > ! > > > interface Vlan12 > > > ip address 150.100.12.13 255.255.255.0 > > > ! > > > interface Vlan40 > > > ip address 150.100.40.13 255.255.255.0 > > > ! > > > interface Vlan100 > > > ip address 100.100.100.13 255.255.255.0 > > > ! > > > interface Vlan200 > > > ip address 100.100.200.13 255.255.255.0 > > > ! > > > interface Vlan300 > > > ip address 100.100.250.13 255.255.255.0 > > > ! > > > interface Vlan567 > > > ip address 150.100.220.13 255.255.255.240 > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 011A1601431B031D35 > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 060F1F24545E0C0B11 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > Cat3(config-if)# > > > > > > .................................... > > > > > > Cat4 > > > > > > Connected to Dynamips VM "Cat4" (ID 7, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > Cat4(config-if)# > > > Cat4(config-if)# > > > Cat4(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 4040 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname Cat4 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > vtp domain ipexpert > > > vtp mode transparent > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > vlan 12 > > > name VLANB > > > ! > > > vlan 40 > > > name VLANC > > > ! > > > vlan 100 > > > name VLANA > > > ! > > > vlan 200 > > > name VLANE > > > ! > > > vlan 240 > > > ! > > > vlan 300 > > > name VLANF > > > ! > > > vlan 567 > > > name VLAND > > > ! > > > vlan 2200,2300,2567 > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Port-channel3 > > > switchport mode trunk > > > ! > > > interface Port-channel2 > > > switchport mode trunk > > > ! > > > interface Port-channel1 > > > switchport mode trunk > > > ! > > > interface FastEthernet0/0 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet0/1 > > > no ip address > > > shutdown > > > duplex auto > > > speed auto > > > ! > > > interface FastEthernet1/0 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/1 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/2 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/3 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/4 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/5 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/6 > > > switchport access vlan 2567 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/7 > > > switchport access vlan 2567 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/8 > > > switchport access vlan 2200 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/9 > > > switchport access vlan 2300 > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/10 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/11 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/12 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/13 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/14 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet1/15 > > > shutdown > > > duplex full > > > speed 100 > > > ! > > > interface FastEthernet2/0 > > > ! > > > interface FastEthernet2/1 > > > ! > > > interface FastEthernet2/2 > > > ! > > > interface FastEthernet2/3 > > > ! > > > interface FastEthernet2/4 > > > ! > > > interface FastEthernet2/5 > > > ! > > > interface FastEthernet2/6 > > > ! > > > interface FastEthernet2/7 > > > ! > > > interface FastEthernet2/8 > > > ! > > > interface FastEthernet2/9 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/10 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 1 mode on > > > ! > > > interface FastEthernet2/11 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/12 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 2 mode on > > > ! > > > interface FastEthernet2/13 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 3 mode on > > > ! > > > interface FastEthernet2/14 > > > switchport mode trunk > > > duplex full > > > speed 100 > > > channel-group 3 mode on > > > ! > > > interface FastEthernet2/15 > > > ! > > > interface Vlan1 > > > no ip address > > > ! > > > interface Vlan12 > > > ip address 150.100.12.14 255.255.255.0 > > > ! > > > interface Vlan40 > > > ip address 150.100.40.14 255.255.255.0 > > > ! > > > interface Vlan100 > > > ip address 100.100.100.14 255.255.255.0 > > > ! > > > interface Vlan200 > > > ip address 100.100.200.14 255.255.255.0 > > > ! > > > interface Vlan300 > > > ip address 100.100.250.14 255.255.255.0 > > > ! > > > interface Vlan567 > > > ip address 150.100.220.14 255.255.255.240 > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 09455E0C011512001F > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 08285C4B1109000506 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > Cat4(config-if)# > > > > > > > > > ................................... > > > > > > BB1 > > > > > > Connected to Dynamips VM "BB1" (ID 10, type c2600) - Console port > > > Press ENTER to get the prompt. > > > > > > BB1(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 998 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > no service password-encryption > > > ! > > > hostname BB1 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 15 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Ethernet0/0 > > > bandwidth 100000 > > > ip address 100.100.100.100 255.255.255.0 > > > full-duplex > > > ! > > > ip forward-protocol nd > > > ! > > > ip http server > > > no ip http secure-server > > > ! > > > ! > > > control-plane > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password ipexpert > > > login > > > history size 30 > > > line aux 0 > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password ipexpert > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > BB1(config-if)# > > > > > > > > > ..................................... > > > > > > R1 > > > > > > Connected to Dynamips VM "R1" (ID 4, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > R1(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 1471 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname R1 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > vtp interface lo0 only > > > vtp domain server > > > vtp mode transparent > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > > > > interface Loopback0 > > > ip address 200.0.0.1 255.255.255.255 > > > ! > > > interface FastEthernet0/0 > > > ip address 150.100.12.1 255.255.255.0 > > > speed 100 > > > full-duplex > > > ! > > > interface FastEthernet0/1 > > > ip address 100.100.100.1 255.255.255.0 > > > speed 100 > > > full-duplex > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 1047191C1D07171918 > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 060F1F24545E0C0B11 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > R1(config-if)# > > > > > > > > > > > > .................................... > > > > > > > > > R5 > > > > > > > > > Connected to Dynamips VM "R5" (ID 1, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > R5(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 1914 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname R5 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Loopback0 > > > ip address 200.0.0.5 255.255.255.255 > > > ! > > > interface FastEthernet0/0 > > > ip address 150.100.220.5 255.255.255.240 > > > speed 100 > > > full-duplex > > > ! > > > interface Serial0/0 > > > no ip address > > > shutdown > > > clock rate 2000000 > > > ! > > > interface FastEthernet0/1 > > > ip address 150.100.221.5 255.255.255.0 > > > speed 100 > > > full-duplex > > > ! > > > interface Serial0/1 > > > ip address 150.100.100.5 255.255.255.0 > > > encapsulation frame-relay > > > clock rate 64000 > > > no arp frame-relay > > > frame-relay map ip 150.100.100.6 506 broadcast > > > frame-relay map ip 150.100.100.2 502 broadcast > > > frame-relay map ip 150.100.100.5 502 > > > no frame-relay inverse-arp > > > ! > > > interface Serial0/2 > > > ip address 150.100.25.5 255.255.255.0 > > > clock rate 64000 > > > ! > > > interface Serial0/3 > > > no ip address > > > shutdown > > > clock rate 2000000 > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 151B1B091C3A2E363C > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 011A1601431B031D35 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > R5(config-if)# > > > > > > > > > ....................................... > > > > > > > > > R6 > > > > > > > > > Connected to Dynamips VM "R6" (ID 2, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > R6(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 2214 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname R6 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > archive > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Loopback0 > > > ip address 200.0.0.6 255.255.255.255 > > > ! > > > interface MFR1 > > > ip address 150.100.69.6 255.255.255.0 > > > shutdown > > > frame-relay interface-dlci 609 > > > ! > > > interface FastEthernet0/0 > > > ip address 150.100.220.6 255.255.255.240 > > > speed 100 > > > full-duplex > > > ! > > > interface Serial0/0 > > > no ip address > > > shutdown > > > clock rate 2000000 > > > ! > > > interface FastEthernet0/1 > > > ip address 150.100.221.6 255.255.255.0 > > > speed 100 > > > full-duplex > > > ! > > > interface Serial0/1 > > > ip address 150.100.100.6 255.255.255.0 > > > encapsulation frame-relay > > > clock rate 64000 > > > no arp frame-relay > > > frame-relay map ip 150.100.100.5 605 broadcast > > > frame-relay map ip 150.100.100.2 602 broadcast > > > frame-relay map ip 150.100.100.6 602 > > > no frame-relay inverse-arp > > > ! > > > interface Serial2/0 > > > ip address 150.100.69.6 255.255.255.0 > > > serial restart-delay 0 > > > clock rate 64000 > > > ! > > > interface Serial2/1 > > > ip address 150.100.96.6 255.255.255.0 > > > serial restart-delay 0 > > > clock rate 64000 > > > ! > > > interface Serial2/2 > > > no ip address > > > shutdown > > > serial restart-delay 0 > > > ! > > > interface Serial2/3 > > > no ip address > > > shutdown > > > serial restart-delay 0 > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^C UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 0502160A395C4B1B0D > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 011A1601431B031D35 > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > R6(config-if)# > > > > > > > > > > > > > > > ................................. > > > > > > > > > R7 > > > > > > Connected to Dynamips VM "R7" (ID 3, type c3725) - Console port > > > Press ENTER to get the prompt. > > > > > > R7(config-if)# > > > R7(config-if)# > > > R7(config-if)#do sh run > > > Building configuration... > > > > > > Current configuration : 1888 bytes > > > ! > > > version 12.4 > > > service timestamps debug datetime msec > > > service timestamps log datetime msec > > > service password-encryption > > > ! > > > hostname R7 > > > ! > > > boot-start-marker > > > boot-end-marker > > > ! > > > ! > > > no aaa new-model > > > memory-size iomem 5 > > > ip cef > > > ! > > > ! > > > ! > > > ! > > > no ip domain lookup > > > ! > > > multilink bundle-name authenticated > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > archive > > > --More-- > > > *Mar 1 00:33:47.727: %LINEPROTO-5-UPDOWN: Line protocol on Interface > > > Serial0/0, changed state to down > > > log config > > > hidekeys > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > interface Loopback0 > > > ip address 200.0.0.7 255.255.255.255 > > > ! > > > interface MFR1 > > > ip address 150.100.69.6 255.255.255.0 > > > shutdown > > > frame-relay interface-dlci 609 > > > ! > > > interface FastEthernet0/0 > > > ip address 150.100.220.7 255.255.255.240 > > > speed 100 > > > full-duplex > > > ! > > > interface Serial0/0 > > > ip address 150.100.78.7 255.255.255.0 > > > clock rate 64000 > > > ! > > > interface FastEthernet0/1 > > > ip address 150.100.221.7 255.255.255.0 > > > speed 100 > > > full-duplex > > > ! > > > interface Serial0/1 > > > ip address 150.100.100.6 255.255.255.0 > > > encapsulation frame-relay > > > shutdown > > > clock rate 64000 > > > no arp frame-relay > > > frame-relay map ip 150.100.100.6 602 > > > frame-relay map ip 150.100.100.2 602 broadcast > > > frame-relay map ip 150.100.100.5 605 broadcast > > > no frame-relay inverse-arp > > > ! > > > ip forward-protocol nd > > > ! > > > ! > > > no ip http server > > > no ip http secure-server > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > control-plane > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > ! > > > banner motd ^CC UNAUTHORISED ACCESS IS STRICTLY FORBIDDEN ^C > > > alias exec myip sh ip int br | exc unass > > > alias exec siib sh ip int br > > > alias exec sir sh ip route > > > alias exec fm sh frame map > > > alias exec fp sh frame pvc > > > alias exec cdp sh cdp nei > > > alias exec sit sh int tr > > > alias exec sip sh ip protocol > > > alias exec vtp sh vtp stat > > > alias exec vls sh vlan-sw > > > ! > > > line con 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 0706314956191C1703 > > > logging synchronous > > > login > > > history size 30 > > > line aux 0 > > > exec-timeout 0 0 > > > privilege level 15 > > > logging synchronous > > > line vty 0 4 > > > exec-timeout 0 0 > > > privilege level 15 > > > password 7 130C0717131C01383F > > > logging synchronous > > > login > > > history size 30 > > > ! > > > ! > > > end > > > > > > R7(config-if)# > > > > > > ...................................... > > > > > > > > > End of CCIE_RS Digest, Vol 88, Issue 24 > > > *************************************** > > > > > > End of CCIE_RS Digest, Vol 88, Issue 25 > > *************************************** > > > > > _______________________________________________ > For more information regarding industry leading CCIE Lab training, please > visit www.ipexpert.com > > Are you a CCNP or CCIE and looking for a job? Check out > www.PlatinumPlacement.com > > http://onlinestudylist.com/mailman/listinfo/ccie_rs > _______________________________________________ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://onlinestudylist.com/mailman/listinfo/ccie_rs
