Unless I'm missing something it's not coming up.
R2#sh run int g0/0
Building configuration...
Current configuration : 93 bytes
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
media-type rj45
end
R2#sh int g0/0
GigabitEthernet0/0 is up, line protocol is down
Hardware is BCM1125 Internal MAC, address is 0011.9368.a0d0 (bia
0011.9368.a0d0)
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Unknown duplex, Unknown Speed, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
Cat1(config-if)#do sh run int g0/2
Building configuration...
Current configuration : 71 bytes
!
interface GigabitEthernet0/2
switchport mode dynamic desirable
end
Cat1(config-if)#do sh int g0/2
GigabitEthernet0/2 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 0012.01b0.f11a (bia
0012.01b0.f11a)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto, media type is 1000BaseSX
input flow-control is off, output flow-control is desired
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
On Mon, Mar 22, 2010 at 4:29 PM, Marko Milivojevic <[email protected]>wrote:
> Ah, sorry. We updated Volume 2. Still, Volume 1 is correct. Please
> consult the general connectivity diagram in the WB - it's all there.
>
> --
> Marko Milivojevic - CCIE #18427
> Senior Technical Instructor - IPexpert
>
> YES! We include 400 hours of REAL rack
> time with our Blended Learning Solution!
>
> Mailto: [email protected]
> Telephone: +1.810.326.1444
> Fax: +1.810.454.0130
> Web: http://www.ipexpert.com/
>
> On Mon, Mar 22, 2010 at 20:21, Marko Milivojevic <[email protected]>
> wrote:
> > Hello,
> >
> > We have JUST uploaded revised documents. Please, get the updated
> documents.
> >
> > Gi0/0 on R2 is connected to Cat1 Gi0/2.
> >
> > --
> > Marko Milivojevic - CCIE #18427
> > Senior Technical Instructor - IPexpert
> >
> > YES! We include 400 hours of REAL rack
> > time with our Blended Learning Solution!
> >
> > Mailto: [email protected]
> > Telephone: +1.810.326.1444
> > Fax: +1.810.454.0130
> > Web: http://www.ipexpert.com/
> >
> > On Mon, Mar 22, 2010 at 20:17, FoosYou <[email protected]> wrote:
> >> Just getting started with the IPX Vol1 Lab1 and I'm not sure if this is
> a
> >> typo or I'm missing something. The VLAN/router interface table wants
> R2's
> >> Gig0/0 interface put into VLAN 12. I'm not seeing Gig 0/0 on R2
> connected to
> >> anything based on the diagrams or via CDP with the interface enabled.
> >>
> >> Thanks!
> >> Jay
> >>
> >> _______________________________________________
> >> For more information regarding industry leading CCIE Lab training,
> please
> >> visit www.ipexpert.com
> >>
> >>
> >
>
_______________________________________________
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
