Hi,
I've been unable to boot the standard current install on my pine a64
lts model.
There is no bugs that I can see, it just stalls at the last line (in the
log attached).
I am not sure what to make of that and how to debug this.
This has been happening for a while now and I have no clue how to go
forward with this.
Aisha
U-Boot SPL 2021.04 (Jun 10 2021 - 09:39:29 -0600)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL31: v2.4(debug):2.4
NOTICE: BL31: Built : 08:24:47, Jun 9 2021
NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689)
NOTICE: BL31: Found U-Boot DTB at 0x4096018, model: Pine64 LTS
INFO: ARM GICv2 driver initialized
INFO: Configuring SPC Controller
INFO: PMIC: Probing AXP803 on RSB
INFO: PMIC: dcdc1 voltage: 3.300V
INFO: PMIC: dcdc5 voltage: 1.200V
INFO: PMIC: dcdc6 voltage: 1.100V
INFO: PMIC: dldo1 voltage: 3.300V
INFO: PMIC: dldo2 voltage: 3.300V
INFO: PMIC: dldo4 voltage: 3.300V
INFO: PMIC: fldo1 voltage: 1.200V
INFO: PMIC: Enabling DC SW
INFO: BL31: Platform setup done
INFO: BL31: Initializing runtime services
INFO: BL31: cortex_a53: CPU workaround for 843419 was applied
INFO: BL31: cortex_a53: CPU workaround for 855873 was applied
WARNING: BL31: cortex_a53: CPU workaround for 1530924 was missing!
NOTICE: PSCI: System suspend is unavailable
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x4a000000
INFO: SPSR = 0x3c9
U-Boot 2021.04 (Jun 10 2021 - 09:39:29 -0600) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: Pine64 LTS
DRAM: 2 GiB
MMC: mmc@1c0f000: 0, mmc@1c11000: 1
Loading Environment from FAT... Card did not respond to voltage select!
: -110
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
Bus usb@1c1a000: USB EHCI 1.00
Bus usb@1c1a400: USB OHCI 1.0
Bus usb@1c1b000: USB EHCI 1.00
Bus usb@1c1b400: USB OHCI 1.0
scanning bus usb@1c1a000 for devices... 1 USB Device(s) found
scanning bus usb@1c1a400 for devices... 1 USB Device(s) found
scanning bus usb@1c1b000 for devices... 1 USB Device(s) found
scanning bus usb@1c1b400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Scanning disk [email protected]...
** Unrecognized filesystem type **
Card did not respond to voltage select! : -110
Scanning disk [email protected]...
Disk [email protected] not ready
Found 3 disks
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image
Found EFI removable media binary efi/boot/bootaa64.efi
168888 bytes read in 11 ms (14.6 MiB/s)
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Booting /efi\boot\bootaa64.efi
disks: sd0*
>> OpenBSD/arm64 BOOTAA64 1.5
boot>
booting sd0a:/bsd: 8958144+1813760+571744+833144
[649766+109+1088088+637088]=0xf9b128
EHCI failed to shut down host controller.
type 0x2 pa 0x40000000 va 0x40000000 pages 0x4000 attr 0x8
type 0x7 pa 0x44000000 va 0x44000000 pages 0x3ef3 attr 0x8
type 0x9 pa 0x47ef3000 va 0x47ef3000 pages 0x1a attr 0x8
type 0x7 pa 0x47f0d000 va 0x47f0d000 pages 0x70ee0 attr 0x8
type 0x4 pa 0xb8ded000 va 0xb8ded000 pages 0x1 attr 0x8
type 0x7 pa 0xb8dee000 va 0xb8dee000 pages 0x1 attr 0x8
type 0x2 pa 0xb8def000 va 0xb8def000 pages 0x100 attr 0x8
type 0x1 pa 0xb8eef000 va 0xb8eef000 pages 0x2a attr 0x8
type 0x0 pa 0xb8f19000 va 0xb8f19000 pages 0x7 attr 0x8
type 0x4 pa 0xb8f20000 va 0xb8f20000 pages 0x1 attr 0x8
type 0x6 pa 0xb8f21000 va 0x5419019000 pages 0x1 attr 0x8000000000000008
type 0x4 pa 0xb8f22000 va 0xb8f22000 pages 0x2 attr 0x8
type 0x0 pa 0xb8f24000 va 0xb8f24000 pages 0x1 attr 0x8
type 0x6 pa 0xb8f25000 va 0x541901d000 pages 0x3 attr 0x8000000000000008
type 0x4 pa 0xb8f28000 va 0xb8f28000 pages 0x1 attr 0x8
type 0x6 pa 0xb8f29000 va 0x5419021000 pages 0x4 attr 0x8000000000000008
type 0x0 pa 0xb8f2d000 va 0xb8f2d000 pages 0x1 attr 0x8
type 0x4 pa 0xb8f2e000 va 0xb8f2e000 pages 0x1 attr 0x8
type 0x0 pa 0xb8f2f000 va 0xb8f2f000 pages 0x1 attr 0x8
type 0x4 pa 0xb8f30000 va 0xb8f30000 pages 0x2 attr 0x8
type 0x0 pa 0xb8f32000 va 0xb8f32000 pages 0x1 attr 0x8
type 0x4 pa 0xb8f33000 va 0xb8f33000 pages 0x2 attr 0x8
type 0x2 pa 0xb8f35000 va 0xb8f35000 pages 0x501b attr 0x8
type 0x5 pa 0xbdf50000 va 0x541e048000 pages 0x20 attr 0x8000000000000008
type 0x2 pa 0xbdf70000 va 0xbdf70000 pages 0x2090 attr 0x8
[ using 2376016 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2021 OpenBSD. All rights reserved.
https://www.OpenBSD.org
OpenBSD 6.9-current (GENERIC.MP) #1209: Sat Jun 19 09:34:02 MDT 2021
[email protected]:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 2027761664 (1933MB)
avail mem = 1932980224 (1843MB)
random: good seed from bootblocks
mainbus0 at root: Pine64 LTS
psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu0: 512KB 64b/line 16-way L2 cache
cpu0: CRC32,SHA2,SHA1,AES+PMULL,ASID16
cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu1: 512KB 64b/line 16-way L2 cache
cpu1: CRC32,SHA2,SHA1,AES+PMULL,ASID16
cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu2: 512KB 64b/line 16-way L2 cache
cpu2: CRC32,SHA2,SHA1,AES+PMULL,ASID16
cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
cpu3: 512KB 64b/line 16-way L2 cache
cpu3: CRC32,SHA2,SHA1,AES+PMULL,ASID16
efi0 at mainbus0: UEFI 2.8
efi0: Das U-Boot rev 0x20210400
apm0 at mainbus0
"display-engine" at mainbus0 not configured
"osc24M_clk" at mainbus0 not configured
"osc32k_clk" at mainbus0 not configured
"pmu" at mainbus0 not configured
simpleaudio0 at mainbus0
agtimer0 at mainbus0: 24000 kHz
simplebus0 at mainbus0: "soc"
sxisyscon0 at simplebus0
sxisid0 at simplebus0
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1: "interrupt-controller"
sxirtc0 at simplebus0
sxiccmu1 at simplebus0
sxipio1 at simplebus0: 13 pins
sxirsb0 at simplebus0
axppmic0 at sxirsb0 addr 0x3a3: AXP803
"bus" at simplebus0 not configured
"dma-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"lcd-controller" at simplebus0 not configured
"video-codec" at simplebus0 not configured
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
sximmc1 at simplebus0
sdmmc1 at sximmc1: 8-bit, sd high-speed, mmc high-speed, dma
"crypto" at simplebus0 not configured
"mailbox" at simplebus0 not configured
"usb" at simplebus0 not configured
"phy" at simplebus0 not configured
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
ohci0 at simplebus0: version 1.0
ehci1 at simplebus0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
ohci1 at simplebus0: version 1.0
"dai" at simplebus0 not configured
"codec" at simplebus0 not configured
sxitemp0 at simplebus0
com0 at simplebus0: ns16550, no working fifo
com0: console
"spi" at simplebus0 not configured
dwxe0 at simplebus0: address 02:ba:17:b1:0f:02
rgephy0 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5
"gpu" at simplebus0 not configured
"dram-controller" at simplebus0 not configured
"deinterlace" at simplebus0 not configured
"hdmi" at simplebus0 not configured
"hdmi-phy" at simplebus0 not configured
"interrupt-controller" at simplebus0 not configured
"codec-analog" at simplebus0 not configured
sxidog0 at simplebus0
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio1: 32 pins
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev
1.00/1.00 addr 1
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev
1.00/1.00 addr 1
"opp_table0" at mainbus0 not configured
"hdmi-connector" at mainbus0 not configured
"vcc1v8" at mainbus0 not configured
"binman" at mainbus0 not configured
dt: 445 probes
sdmmc1: can't enable card
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, GD2S5, 0030> removable
sd0: 122240MB, 512 bytes/sector, 250347520 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on sd0a (d9101244a2405405.a) swap on sd0b dump on sd0b
