Hi, When booting an Asus Zenbook 3 (UX390UA) while the included USB Hub with a USB stick is connected, the USB stick may not be recognized.
I tested booting in two different ways: 1. GENERIC.MP (current 2018-01-24) installed on the hard drive. Results are reproducible: stick never recognized, un- and replugging either the stick or the hub always gets it recognized. 2. RAMDISK_CD (current 2018-01-24) from the install62.fs image, booted from the same USB stick. Results look non-deterministic: sometimes it is recognized at boot, sometimes (more often) not. Replugging may or may not get it recognized. The USB-A stick is plugged into the hub (https://www.asus.com/Laptops-Accessory/Mini-Dock/), which is plugged into the laptop's USB-C port. All reboots were done cold. In more detail: 1. GENERIC.MP from hard drive fails to recognize the stick, i.e. no "sd1" line appears (reproducible): uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub" rev 2.10/6.80 addr 2 ...hangs for 20 seconds... uhub1: port 1, set config 0 at addr 3 failed uhub1: device problem, disabling port 1 ugen0 at uhub1 port 2 "VIA Technologies Inc. USB 2.0 BILLBOARD" rev 2.01/3.04 addr 3 When subsequently simply un- and replugging the stick, it does appear (this always works at the first attempt): umass0 at uhub1 port 1 configuration 1 interface 0 "Verbatim STORE N GO" rev 2.00/1.00 addr 8 umass0: using SCSI over Bulk-Only scsibus4 at umass0: 2 targets, initiator 0 sd1 at scsibus4 targ 1 lun 0: <Verbatim, STORE N GO, 8.07> SCSI2 0/direct removable sd1: 3728MB, 512 bytes/sector, 7634944 sectors When booting with only the hub, but without the stick, no hanging occurs and the two lines saying "failed" and "device problem" disappear. Plugging in the stick subsequently works. 2. RAMDISK_CD from the USB stick Sometimes the stick is recognized immediately and the expected output shows in dmesg: uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub" rev 2.10/6.80 addr 2 umass0 at uhub1 port 1 configuration 1 interface 0 "Verbatim STORE N GO" rev 2.00/1.00 addr 3 umass0: using SCSI over Bulk-Only scsibus1 at umass0: 2 targets, initiator 0 sd1 at scsibus1 targ 1 lun 0: <Verbatim, STORE N GO, 8.07> SCSI2 0/direct removable sd1: 3728MB, 512 bytes/sector, 7634944 sectors "VIA Technologies Inc. USB 2.0 BILLBOARD" rev 2.01/3.04 addr 4 at uhub1 port 2 not configured But more often (apparently non-deterministically) we get: uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub" rev 2.10/6.80 addr 2 ...hangs for 20 seconds... uhub1: port 1, set config 0 at addr 3 failed uhub1: device problem, disabling port 1 "VIA Technologies Inc. USB 2.0 BILLBOARD" rev 2.01/3.04 addr 3 at uhub1 port 2 not configured Now replugging the hub or stick may or may not work. Sometimes it works after replugging many times. Below are three dmesg outputs, corresponding to scenarios 1 (GENERIC.MP from hard drive) and 2 (RAMDISK from USB stick). For the latter, first the case where it is recognized and then the one where it isn't. Best, Max OpenBSD 6.2-current (GENERIC.MP) #387: Wed Jan 24 12:53:55 MST 2018 [email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP real mem = 17037766656 (16248MB) avail mem = 16514473984 (15749MB) mpath0 at root scsibus0 at mpath0: 256 targets mainbus0 at root bios0 at mainbus0: SMBIOS rev. 3.0 @ 0xeb350 (31 entries) bios0: vendor American Megatrends Inc. version "UX390UAK.312" date 04/25/2017 bios0: ASUSTeK COMPUTER INC. UX390UAK acpi0 at bios0: rev 2 acpi0: sleep states S0 S3 S4 S5 acpi0: tables DSDT FACP APIC FPDT ECDT MCFG FIDT SSDT MSDM SSDT HPET UEFI SSDT LPIT WSMT SSDT SSDT DBGP DBG2 BGRT DMAR TPM2 acpi0: wakeup devices GLAN(S4) XHC_(S3) XDCI(S4) HDAS(S4) acpitimer0 at acpi0: 3579545 Hz, 24 bits acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz, 2594.87 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT cpu0: 256KB 64b/line 8-way L2 cache cpu0: smt 0, core 0, package 0 mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges cpu0: apic clock running at 24MHz cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1.1.1, IBE cpu1 at mainbus0: apid 2 (application processor) cpu1: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz, 2593.97 MHz cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT cpu1: 256KB 64b/line 8-way L2 cache cpu1: smt 0, core 1, package 0 cpu2 at mainbus0: apid 1 (application processor) cpu2: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz, 2593.97 MHz cpu2: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT cpu2: 256KB 64b/line 8-way L2 cache cpu2: smt 1, core 0, package 0 cpu3 at mainbus0: apid 3 (application processor) cpu3: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz, 2593.97 MHz cpu3: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT cpu3: 256KB 64b/line 8-way L2 cache cpu3: smt 1, core 1, package 0 ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 120 pins acpiec0 at acpi0 acpimcfg0 at acpi0 addr 0xf0000000, bus 0-127 acpihpet0 at acpi0: 23999999 Hz acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus -1 (PEG0) acpiprt2 at acpi0: bus -1 (PEG1) acpiprt3 at acpi0: bus -1 (PEG2) acpiprt4 at acpi0: bus 3 (RP09) acpiprt5 at acpi0: bus -1 (RP10) acpiprt6 at acpi0: bus -1 (RP11) acpiprt7 at acpi0: bus -1 (RP12) acpiprt8 at acpi0: bus -1 (RP13) acpiprt9 at acpi0: bus 1 (RP01) acpiprt10 at acpi0: bus -1 (RP02) acpiprt11 at acpi0: bus -1 (RP03) acpiprt12 at acpi0: bus -1 (RP04) acpiprt13 at acpi0: bus -1 (RP05) acpiprt14 at acpi0: bus 2 (RP06) acpiprt15 at acpi0: bus -1 (RP07) acpiprt16 at acpi0: bus -1 (RP08) acpiprt17 at acpi0: bus -1 (RP17) acpiprt18 at acpi0: bus -1 (RP18) acpiprt19 at acpi0: bus -1 (RP19) acpiprt20 at acpi0: bus -1 (RP20) acpiprt21 at acpi0: bus -1 (RP14) acpiprt22 at acpi0: bus -1 (RP15) acpiprt23 at acpi0: bus -1 (RP16) acpiec at acpi0 not configured acpicpu0 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33), C1(1000@1 mwait.1), PSS acpicpu1 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33), C1(1000@1 mwait.1), PSS acpicpu2 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33), C1(1000@1 mwait.1), PSS acpicpu3 at acpi0: C3(200@1034 mwait.1@0x60), C2(200@151 mwait.1@0x33), C1(1000@1 mwait.1), PSS acpipwrres0 at acpi0: WRST acpipwrres1 at acpi0: WRST acpipwrres2 at acpi0: WRST acpipwrres3 at acpi0: WRST acpipwrres4 at acpi0: WRST acpipwrres5 at acpi0: WRST acpipwrres6 at acpi0: WRST acpipwrres7 at acpi0: WRST acpipwrres8 at acpi0: WRST acpipwrres9 at acpi0: WRST acpipwrres10 at acpi0: WRST acpipwrres11 at acpi0: WRST acpipwrres12 at acpi0: WRST acpipwrres13 at acpi0: WRST acpipwrres14 at acpi0: WRST acpipwrres15 at acpi0: WRST acpipwrres16 at acpi0: WRST acpipwrres17 at acpi0: WRST acpipwrres18 at acpi0: WRST acpipwrres19 at acpi0: WRST acpitz0 at acpi0: critical temperature is 103 degC "INT3F0D" at acpi0 not configured acpiac0 at acpi0: AC unit offline acpibtn0 at acpi0: LID_ acpibat0 at acpi0: BAT0 model "ASUS Battery" serial type LIon oem "ASUSTeK" "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "ATK3001" at acpi0 not configured "ELAN1301" at acpi0 not configured acpibtn1 at acpi0: SLPB "INT33A1" at acpi0 not configured acpibtn2 at acpi0: PWRB "MSFT0101" at acpi0 not configured "PNP0C14" at acpi0 not configured "ATK4002" at acpi0 not configured "INT3400" at acpi0 not configured "INT340E" at acpi0 not configured acpivideo0 at acpi0: GFX0 acpivout0 at acpivideo0: DD1F cpu0: Enhanced SpeedStep 2594 MHz: speeds: 2701, 2700, 2600, 2500, 2400, 2200, 2000, 1800, 1600, 1500, 1300, 1100, 800, 700, 600, 400 MHz pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel Core 7G Host" rev 0x02 inteldrm0 at pci0 dev 2 function 0 "Intel HD Graphics 620" rev 0x02 drm0 at inteldrm0 inteldrm0: msi error: [drm:pid0:i915_firmware_load_error_print] *ERROR* failed to load firmware i915/kbl_dmc_ver1.bin (-22) inteldrm0: 1920x1080, 32bpp wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation) wsdisplay0: screen 1-5 added (std, vt100 emulation) "Intel Core 6G Thermal" rev 0x02 at pci0 dev 4 function 0 not configured xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x21: msi usb0 at xhci0: USB revision 3.0 uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00 addr 1 pchtemp0 at pci0 dev 20 function 2 "Intel 100 Series Thermal" rev 0x21 dwiic0 at pci0 dev 21 function 0 "Intel 100 Series I2C" rev 0x21: apic 2 int 16 iic0 at dwiic0 dwiic1 at pci0 dev 21 function 1 "Intel 100 Series I2C" rev 0x21: apic 2 int 17 iic1 at dwiic1 ihidev0 at iic1 addr 0x15 (polling), vendor 0x4f3 product 0x3035, ELAN1301 ihidev0: 11 report ids imt0 at ihidev0: clickpad, 5 contacts wsmouse0 at imt0 mux 0 "Intel 100 Series MEI" rev 0x21 at pci0 dev 22 function 0 not configured ppb0 at pci0 dev 28 function 0 "Intel 100 Series PCIE" rev 0xf1 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 5 "Intel 100 Series PCIE" rev 0xf1: msi pci2 at ppb1 bus 2 iwm0 at pci2 dev 0 function 0 "Intel Dual Band Wireless AC 8260" rev 0x3a, msi ppb2 at pci0 dev 29 function 0 "Intel 100 Series PCIE" rev 0xf1: msi pci3 at ppb2 bus 3 nvme0 at pci3 dev 0 function 0 vendor "Toshiba", unknown product 0x010f rev 0x01: msi, NVMe 1.1 nvme0: THNSN5512GPU7 TOSHIBA, firmware 57XA4104, serial Y63S108UT7DV scsibus1 at nvme0: 1 targets sd0 at scsibus1 targ 0 lun 0: <NVMe, THNSN5512GPU7 TO, 57XA> SCSI4 0/direct fixed sd0: 488386MB, 512 bytes/sector, 1000215216 sectors pcib0 at pci0 dev 31 function 0 "Intel 200 Series LPC" rev 0x21 "Intel 100 Series PMC" rev 0x21 at pci0 dev 31 function 2 not configured azalia0 at pci0 dev 31 function 3 "Intel 200 Series HD Audio" rev 0x21: msi azalia0: codecs: Realtek/0x0295, Intel/0x280b, using Realtek/0x0295 audio0 at azalia0 ichiic0 at pci0 dev 31 function 4 "Intel 100 Series SMBus" rev 0x21: apic 2 int 16 iic2 at ichiic0 isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 irq 1 irq 12 pckbd0 at pckbc0 (kbd slot) wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 vmm0 at mainbus0: VMX/EPT efifb at mainbus0 not configured uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub" rev 2.10/6.80 addr 2 uhub1: port 1, set config 0 at addr 3 failed uhub1: device problem, disabling port 1 ugen0 at uhub1 port 2 "VIA Technologies Inc. USB 2.0 BILLBOARD" rev 2.01/3.04 addr 3 uvideo0 at uhub0 port 5 configuration 1 interface 0 "AzureWave USB2.0 VGA UVC WebCam" rev 2.00/16.09 addr 4 video0 at uvideo0 ugen1 at uhub0 port 8 "Intel Bluetooth" rev 2.00/0.01 addr 5 ugen2 at uhub0 port 9 "ELAN ELAN:Fingerprint" rev 2.00/1.35 addr 6 uhub2 at uhub0 port 13 configuration 1 interface 0 "VIA Labs, Inc. USB3.0 Hub" rev 3.00/6.85 addr 7 vscsi0 at root scsibus2 at vscsi0: 256 targets softraid0 at root scsibus3 at softraid0: 256 targets root on sd0a (6c960f4084fc9908.a) swap on sd0b dump on sd0b iwm0: hw rev 0x200, fw ver 16.242414.0, address a0:c5:89:44:a6:2e OpenBSD 6.2-current (RAMDISK_CD) #379: Wed Jan 24 12:58:41 MST 2018 [email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD real mem = 17037766656 (16248MB) avail mem = 16517648384 (15752MB) mainbus0 at root bios0 at mainbus0: SMBIOS rev. 3.0 @ 0xeb350 (31 entries) bios0: vendor American Megatrends Inc. version "UX390UAK.312" date 04/25/2017 bios0: ASUSTeK COMPUTER INC. UX390UAK acpi0 at bios0: rev 2 acpi0: tables DSDT FACP APIC FPDT ECDT MCFG FIDT SSDT MSDM SSDT HPET UEFI SSDT LPIT WSMT SSDT SSDT DBGP DBG2 DMAR TPM2 BGRT acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz, 2594.88 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT cpu0: 256KB 64b/line 8-way L2 cache cpu0: apic clock running at 23MHz cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1.1.1, IBE cpu at mainbus0: not configured cpu at mainbus0: not configured cpu at mainbus0: not configured ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 120 pins acpiec0 at acpi0 acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus -1 (PEG0) acpiprt2 at acpi0: bus -1 (PEG1) acpiprt3 at acpi0: bus -1 (PEG2) acpiprt4 at acpi0: bus 3 (RP09) acpiprt5 at acpi0: bus -1 (RP10) acpiprt6 at acpi0: bus -1 (RP11) acpiprt7 at acpi0: bus -1 (RP12) acpiprt8 at acpi0: bus -1 (RP13) acpiprt9 at acpi0: bus 1 (RP01) acpiprt10 at acpi0: bus -1 (RP02) acpiprt11 at acpi0: bus -1 (RP03) acpiprt12 at acpi0: bus -1 (RP04) acpiprt13 at acpi0: bus -1 (RP05) acpiprt14 at acpi0: bus 2 (RP06) acpiprt15 at acpi0: bus -1 (RP07) acpiprt16 at acpi0: bus -1 (RP08) acpiprt17 at acpi0: bus -1 (RP17) acpiprt18 at acpi0: bus -1 (RP18) acpiprt19 at acpi0: bus -1 (RP19) acpiprt20 at acpi0: bus -1 (RP20) acpiprt21 at acpi0: bus -1 (RP14) acpiprt22 at acpi0: bus -1 (RP15) acpiprt23 at acpi0: bus -1 (RP16) acpiec at acpi0 not configured acpicpu at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpitz at acpi0 not configured "INT3F0D" at acpi0 not configured "ACPI0003" at acpi0 not configured "PNP0C0D" at acpi0 not configured "PNP0C0A" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "ATK3001" at acpi0 not configured "ELAN1301" at acpi0 not configured "PNP0C0E" at acpi0 not configured "INT33A1" at acpi0 not configured "PNP0C0C" at acpi0 not configured "MSFT0101" at acpi0 not configured "PNP0C14" at acpi0 not configured "ATK4002" at acpi0 not configured "INT3400" at acpi0 not configured "INT340E" at acpi0 not configured pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel Core 7G Host" rev 0x02 "Intel HD Graphics 620" rev 0x02 at pci0 dev 2 function 0 not configured "Intel Core 6G Thermal" rev 0x02 at pci0 dev 4 function 0 not configured xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x21: msi usb0 at xhci0: USB revision 3.0 uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00 addr 1 "Intel 100 Series Thermal" rev 0x21 at pci0 dev 20 function 2 not configured dwiic0 at pci0 dev 21 function 0 "Intel 100 Series I2C" rev 0x21: apic 2 int 16 iic0 at dwiic0 dwiic1 at pci0 dev 21 function 1 "Intel 100 Series I2C" rev 0x21: apic 2 int 17 iic1 at dwiic1 ihidev0 at iic1 addr 0x15 (polling), vendor 0x4f3 product 0x3035, ELAN1301 ihidev0: 11 report ids hid at ihidev0 reportid 1 not configured hid at ihidev0 reportid 2 not configured hid at ihidev0 reportid 3 not configured hid at ihidev0 reportid 4 not configured hid at ihidev0 reportid 5 not configured hid at ihidev0 reportid 6 not configured hid at ihidev0 reportid 7 not configured hid at ihidev0 reportid 11 not configured "Intel 100 Series MEI" rev 0x21 at pci0 dev 22 function 0 not configured ppb0 at pci0 dev 28 function 0 "Intel 100 Series PCIE" rev 0xf1 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 5 "Intel 100 Series PCIE" rev 0xf1: msi pci2 at ppb1 bus 2 iwm0 at pci2 dev 0 function 0 "Intel Dual Band Wireless AC 8260" rev 0x3a, msi ppb2 at pci0 dev 29 function 0 "Intel 100 Series PCIE" rev 0xf1: msi pci3 at ppb2 bus 3 nvme0 at pci3 dev 0 function 0 vendor "Toshiba", unknown product 0x010f rev 0x01: msi, NVMe 1.1 nvme0: THNSN5512GPU7 TOSHIBA, firmware 57XA4104, serial Y63S108UT7DV scsibus0 at nvme0: 1 targets sd0 at scsibus0 targ 0 lun 0: <NVMe, THNSN5512GPU7 TO, 57XA> SCSI4 0/direct fixed sd0: 488386MB, 512 bytes/sector, 1000215216 sectors "Intel 200 Series LPC" rev 0x21 at pci0 dev 31 function 0 not configured "Intel 100 Series PMC" rev 0x21 at pci0 dev 31 function 2 not configured "Intel 200 Series HD Audio" rev 0x21 at pci0 dev 31 function 3 not configured "Intel 100 Series SMBus" rev 0x21 at pci0 dev 31 function 4 not configured isa0 at mainbus0 pckbc0 at isa0 port 0x60/5 irq 1 irq 12 pckbd0 at pckbc0 (kbd slot) wskbd0 at pckbd0: console keyboard efifb0 at mainbus0: 1920x1080, 32bpp wsdisplay0 at efifb0 mux 1: console (std, vt100 emulation), using wskbd0 uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub" rev 2.10/6.80 addr 2 umass0 at uhub1 port 1 configuration 1 interface 0 "Verbatim STORE N GO" rev 2.00/1.00 addr 3 umass0: using SCSI over Bulk-Only scsibus1 at umass0: 2 targets, initiator 0 sd1 at scsibus1 targ 1 lun 0: <Verbatim, STORE N GO, 8.07> SCSI2 0/direct removable sd1: 3728MB, 512 bytes/sector, 7634944 sectors "VIA Technologies Inc. USB 2.0 BILLBOARD" rev 2.01/3.04 addr 4 at uhub1 port 2 not configured "AzureWave USB2.0 VGA UVC WebCam" rev 2.00/16.09 addr 5 at uhub0 port 5 not configured "vendor 0x8087 product 0x0a2b" rev 2.00/0.01 addr 6 at uhub0 port 8 not configured "ELAN ELAN:Fingerprint" rev 2.00/1.35 addr 7 at uhub0 port 9 not configured uhub2 at uhub0 port 13 configuration 1 interface 0 "VIA Labs, Inc. USB3.0 Hub" rev 3.00/6.85 addr 8 softraid0 at root scsibus2 at softraid0: 256 targets root on rd0a swap on rd0b dump on rd0b iwm0: could not read firmware iwm-8000C-16 (error 2) iwm0: failed to load init firmware OpenBSD 6.2-current (RAMDISK_CD) #379: Wed Jan 24 12:58:41 MST 2018 [email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD real mem = 17037766656 (16248MB) avail mem = 16517648384 (15752MB) mainbus0 at root bios0 at mainbus0: SMBIOS rev. 3.0 @ 0xeb350 (31 entries) bios0: vendor American Megatrends Inc. version "UX390UAK.312" date 04/25/2017 bios0: ASUSTeK COMPUTER INC. UX390UAK acpi0 at bios0: rev 2 acpi0: tables DSDT FACP APIC FPDT ECDT MCFG FIDT SSDT MSDM SSDT HPET UEFI SSDT LPIT WSMT SSDT SSDT DBGP DBG2 DMAR TPM2 BGRT acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Core(TM) i7-7500U CPU @ 2.70GHz, 2594.85 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,SENSOR,ARAT cpu0: 256KB 64b/line 8-way L2 cache cpu0: apic clock running at 23MHz cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1.1.1, IBE cpu at mainbus0: not configured cpu at mainbus0: not configured cpu at mainbus0: not configured ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 120 pins acpiec0 at acpi0 acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus -1 (PEG0) acpiprt2 at acpi0: bus -1 (PEG1) acpiprt3 at acpi0: bus -1 (PEG2) acpiprt4 at acpi0: bus 3 (RP09) acpiprt5 at acpi0: bus -1 (RP10) acpiprt6 at acpi0: bus -1 (RP11) acpiprt7 at acpi0: bus -1 (RP12) acpiprt8 at acpi0: bus -1 (RP13) acpiprt9 at acpi0: bus 1 (RP01) acpiprt10 at acpi0: bus -1 (RP02) acpiprt11 at acpi0: bus -1 (RP03) acpiprt12 at acpi0: bus -1 (RP04) acpiprt13 at acpi0: bus -1 (RP05) acpiprt14 at acpi0: bus 2 (RP06) acpiprt15 at acpi0: bus -1 (RP07) acpiprt16 at acpi0: bus -1 (RP08) acpiprt17 at acpi0: bus -1 (RP17) acpiprt18 at acpi0: bus -1 (RP18) acpiprt19 at acpi0: bus -1 (RP19) acpiprt20 at acpi0: bus -1 (RP20) acpiprt21 at acpi0: bus -1 (RP14) acpiprt22 at acpi0: bus -1 (RP15) acpiprt23 at acpi0: bus -1 (RP16) acpiec at acpi0 not configured acpicpu at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpipwrres at acpi0 not configured acpitz at acpi0 not configured "INT3F0D" at acpi0 not configured "ACPI0003" at acpi0 not configured "PNP0C0D" at acpi0 not configured "PNP0C0A" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "INT3403" at acpi0 not configured "ATK3001" at acpi0 not configured "ELAN1301" at acpi0 not configured "PNP0C0E" at acpi0 not configured "INT33A1" at acpi0 not configured "PNP0C0C" at acpi0 not configured "MSFT0101" at acpi0 not configured "PNP0C14" at acpi0 not configured "ATK4002" at acpi0 not configured "INT3400" at acpi0 not configured "INT340E" at acpi0 not configured pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel Core 7G Host" rev 0x02 "Intel HD Graphics 620" rev 0x02 at pci0 dev 2 function 0 not configured "Intel Core 6G Thermal" rev 0x02 at pci0 dev 4 function 0 not configured xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x21: msi usb0 at xhci0: USB revision 3.0 uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00 addr 1 "Intel 100 Series Thermal" rev 0x21 at pci0 dev 20 function 2 not configured dwiic0 at pci0 dev 21 function 0 "Intel 100 Series I2C" rev 0x21: apic 2 int 16 iic0 at dwiic0 dwiic1 at pci0 dev 21 function 1 "Intel 100 Series I2C" rev 0x21: apic 2 int 17 iic1 at dwiic1 ihidev0 at iic1 addr 0x15 (polling), vendor 0x4f3 product 0x3035, ELAN1301 ihidev0: 11 report ids hid at ihidev0 reportid 1 not configured hid at ihidev0 reportid 2 not configured hid at ihidev0 reportid 3 not configured hid at ihidev0 reportid 4 not configured hid at ihidev0 reportid 5 not configured hid at ihidev0 reportid 6 not configured hid at ihidev0 reportid 7 not configured hid at ihidev0 reportid 11 not configured "Intel 100 Series MEI" rev 0x21 at pci0 dev 22 function 0 not configured ppb0 at pci0 dev 28 function 0 "Intel 100 Series PCIE" rev 0xf1 pci1 at ppb0 bus 1 ppb1 at pci0 dev 28 function 5 "Intel 100 Series PCIE" rev 0xf1: msi pci2 at ppb1 bus 2 iwm0 at pci2 dev 0 function 0 "Intel Dual Band Wireless AC 8260" rev 0x3a, msi ppb2 at pci0 dev 29 function 0 "Intel 100 Series PCIE" rev 0xf1: msi pci3 at ppb2 bus 3 nvme0 at pci3 dev 0 function 0 vendor "Toshiba", unknown product 0x010f rev 0x01: msi, NVMe 1.1 nvme0: THNSN5512GPU7 TOSHIBA, firmware 57XA4104, serial Y63S108UT7DV scsibus0 at nvme0: 1 targets sd0 at scsibus0 targ 0 lun 0: <NVMe, THNSN5512GPU7 TO, 57XA> SCSI4 0/direct fixed sd0: 488386MB, 512 bytes/sector, 1000215216 sectors "Intel 200 Series LPC" rev 0x21 at pci0 dev 31 function 0 not configured "Intel 100 Series PMC" rev 0x21 at pci0 dev 31 function 2 not configured "Intel 200 Series HD Audio" rev 0x21 at pci0 dev 31 function 3 not configured "Intel 100 Series SMBus" rev 0x21 at pci0 dev 31 function 4 not configured isa0 at mainbus0 pckbc0 at isa0 port 0x60/5 irq 1 irq 12 pckbd0 at pckbc0 (kbd slot) wskbd0 at pckbd0: console keyboard efifb0 at mainbus0: 1920x1080, 32bpp wsdisplay0 at efifb0 mux 1: console (std, vt100 emulation), using wskbd0 uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs, Inc. USB2.0 Hub" rev 2.10/6.80 addr 2 uhub1: port 1, set config 0 at addr 3 failed uhub1: device problem, disabling port 1 "VIA Technologies Inc. USB 2.0 BILLBOARD" rev 2.01/3.04 addr 3 at uhub1 port 2 not configured "AzureWave USB2.0 VGA UVC WebCam" rev 2.00/16.09 addr 4 at uhub0 port 5 not configured "vendor 0x8087 product 0x0a2b" rev 2.00/0.01 addr 5 at uhub0 port 8 not configured "ELAN ELAN:Fingerprint" rev 2.00/1.35 addr 6 at uhub0 port 9 not configured uhub2 at uhub0 port 13 configuration 1 interface 0 "VIA Labs, Inc. USB3.0 Hub" rev 3.00/6.85 addr 7 softraid0 at root scsibus1 at softraid0: 256 targets root on rd0a swap on rd0b dump on rd0b iwm0: could not read firmware iwm-8000C-16 (error 2) iwm0: failed to load init firmware
