RE: Percent % completed?

[Timothy Johnson]

That's the one. :)

-----Original Message-----
From: Nikola Janceski [mailto:[EMAIL PROTECTED]]
Sent: Thursday, July 25, 2002 10:40 AM
To: 'Timothy Johnson'; 'David Samuelsson (PAC)'; '[EMAIL PROTECTED]'
Subject: RE: Percent % completed?


I think Tim meant:

open(COMMAND, "command |") or die "$!";

while (<COMMAND>){
        #here will come each line of output in $_ while the command runs and
until the command ends.
        }
close COMMAND;

> -----Original Message-----
> From: Timothy Johnson [mailto:[EMAIL PROTECTED]]
> Sent: Thursday, July 25, 2002 1:18 PM
> To: 'David Samuelsson (PAC)'; '[EMAIL PROTECTED]'
> Subject: RE: Percent % completed?
> 
> 
> 
> Perhaps you could open the command to a filehandle
> 
> open(COMMAND,"|command");
> 
> and figure out something from there.  I've never done it, so 
> I'm not sure,
> and I have to run, but that might get you started.
> -----Original Message-----
> From: David Samuelsson (PAC) [mailto:[EMAIL PROTECTED]]
> Sent: Thursday, July 25, 2002 12:28 AM
> To: '[EMAIL PROTECTED]'
> Subject: Percent % completed?
> 
> 
> Hello again out there.
> 
> Is there anyway to get perl to do a counter so it counts in 
> the command
> shell how many % that is done? I have a script that runs a check on a
> database, its just 1 command and it spits out some 
> information. Can i parse
> this information from when its printing out this information, 
> and insted
> capture some variabels and make it count like 0 % ready, 25 % ready or
> similar? its hard since its just 1 command and that spits out all the
> infomation if the database is at good health, but the check can take a
> really long time for some databses and a very short time for 
> not so big
> databases.  But the out put is always the same for the 
> databses unless there
> is an error in them.
> 
> Processing key file: vob_db.k01(1), total of 444 nodes
> 
> 
> ------------------------------------------------------------------
> 
> Processing key file: vob_db.k02(2), total of 840 nodes
> 
> 
> ------------------------------------------------------------------
> 
> Processing key file: vob_db.k03(5), total of 1 node
> 
> 
> ------------------------------------------------------------------
> 
> Processing key file: vob_db.k04(6), total of 1 node
> 
> 
> ------------------------------------------------------------------
> 
> Processing data file: vob_db.d01(0), total of 37651 records
> 
> 
> ------------------------------------------------------------------
> 
> Processing data file: vob_db.d02(3), total of 20628 records
> 
> 
> ------------------------------------------------------------------
> 
> Processing data file: vob_db.d03(4), total of 1 record
> 
> 
> Database consistency check completed
> 
> 0 errors were encountered in 0 records/nodes
> 
> This is the output from the command.  Anyone got a clue on 
> how to make it
> count for each line or something?
> 
> Thanks for any info or similar scripting techniqes.
> 
> //Dave
> 
> -- 
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
> 
> -- 
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
> 

----------------------------------------------------------------------------
--------------------
The views and opinions expressed in this email message are the sender's
own, and do not necessarily represent the views and opinions of Summit
Systems Inc.

-- 
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]