Thank you all..!! Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 9:51:09 μ.μ. UTC+2, ο χρήστης vinicius...@gmail.com έγραψε:
> You can use putty > > Em sáb., 5 de dez. de 2020 às 15:27, John Bacas <john....@gmail.com> > escreveu: > >> As I said I'm a newbie >> Luckily I have an FTDI cable , but what software should I use as a >> console to read data from PB? I have Windows 10. >> >> Actually, when I plug PB to my PC it makes the sound of connecting and a >> COM port appears in the Device Manager, but then another sound of >> disconnecting. This thing repeats for 10 times and finnaly the COM port >> disappears. >> Thnx >> Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 7:12:18 μ.μ. UTC+2, ο χρήστης >> jonn...@gmail.com έγραψε: >> >>> If the LEDs are not blinking as expected, that does not sound good. If >>> you have a FTDI cable, you could try to connect it to the PB as shown on >>> the following page to see if you get any messages related to the issue: >>> >>> https://beagleboard.org/p/ken-shirriff/hands-on-with-the-pocketbeagle-a-25-linux-computer-606c66 >>> >>> I'm assuming you are not seeing a COM port active for the PB on your >>> Windows PC, correct? >>> >>> Cheers, >>> >>> Jon >>> >>> On Sat, Dec 5, 2020 at 5:32 AM John Bacas <john....@gmail.com> wrote: >>> >>>> I have used "*AM3358 Debian 10.3 2020-04-06 4GB SD IoT*" image file >>>> and I used "*rufus 3.1*" to flash the image. >>>> As I said, all 4 leds lighted up sequencially and after a while the >>>> user0 led flashed like a heartbeat and user1 led kept flashing randomly. >>>> That is normal as I have read, but still in my computer no device was >>>> detected. >>>> After some unplugging and plugging, I used "*Etcher*" to flash the >>>> image. >>>> Then I flashed some older images like "*Debian 9.9 2019-08-03 4GB SD >>>> IoT*" and "*AM3358 Debian 10.0 2019-07-07 4GB SD IoT*" with "Etcher" >>>> too. >>>> I have tried a different sd card but nothing changed. >>>> Yesterday when I plugged Beagle in the usb port, an "RNDIS...." message >>>> appeard but not any connection and only user0 led stays constantly lit. >>>> User0 led is about kernel, so is there any damage inside the chip? >>>> >>>> Στις Σάββατο, 5 Δεκεμβρίου 2020 στις 2:39:17 π.μ. UTC+2, ο χρήστης >>>> jonn...@gmail.com έγραψε: >>>> >>>>> What image did you flash to the uSD card? >>>>> What tool did you use to flash the image to the uSD card? >>>>> >>>>> Cheers, >>>>> >>>>> Jon >>>>> >>>>> On Fri, Dec 4, 2020 at 12:36 PM John Bacas <john....@gmail.com> wrote: >>>>> >>>>>> Hi, I'm a newbie with beagle board and I have a problem with my >>>>>> pocket one. >>>>>> I did all according to the quick start guide. >>>>>> When i plugged it to my pc all 4 leds lighted up sequentially but I >>>>>> was waiting for 1 minute and nothing happened. There wasn't any new >>>>>> drive >>>>>> appearing in my windows explorer. >>>>>> Unplugged it without turning it off and plugged it again. Same >>>>>> bahavior. >>>>>> After a lot o sd card flashing and tries to boot, things got worse. >>>>>> Now when i plug the board only user0 led lights up and stays open. >>>>>> Have I damaged it ? How can I check if it has damage? >>>>>> Can I fix it ? >>>>>> >>>>>> Thanks >>>>>> >>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to beagleboard...@googlegroups.com. >>>>>> To view this discussion on the web visit >>>>>> https://groups.google.com/d/msgid/beagleboard/744326f5-f51d-4c41-9771-da5272edb840n%40googlegroups.com >>>>>> >>>>>> <https://groups.google.com/d/msgid/beagleboard/744326f5-f51d-4c41-9771-da5272edb840n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>>> . >>>>>> >>>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to beagleboard...@googlegroups.com. >>>> >>> To view this discussion on the web visit >>>> https://groups.google.com/d/msgid/beagleboard/688b764d-8c22-4429-97d1-39356414818dn%40googlegroups.com >>>> >>>> <https://groups.google.com/d/msgid/beagleboard/688b764d-8c22-4429-97d1-39356414818dn%40googlegroups.com?utm_medium=email&utm_source=footer> >>>> . >>>> >>> -- >> For more options, visit http://beagleboard.org/discuss >> --- >> You received this message because you are subscribed to the Google Groups >> "BeagleBoard" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to beagleboard...@googlegroups.com. >> > To view this discussion on the web visit >> https://groups.google.com/d/msgid/beagleboard/b42ca426-265c-4c80-b56b-4fd6fb1bdd4an%40googlegroups.com >> >> <https://groups.google.com/d/msgid/beagleboard/b42ca426-265c-4c80-b56b-4fd6fb1bdd4an%40googlegroups.com?utm_medium=email&utm_source=footer> >> . >> > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/1482e51d-b2b9-463f-bca3-973eb61b05b9n%40googlegroups.com.
