Hi Guys, my problem is that I need to "switch" between using the display cape and the HDMI output of my BeagleBone Black Rev C. I can't always detach the Display Cape when I want to use HDMI because I plan on fitting my BBB in a permanent case. Is there a possibility to use the HDMI output when the Display Cape is attached to the Board? I can't seem to find an answer in any other questions or forums so I would really appreciate some help.
I'm currently using debian 9.5 with following kernel: 4.14.49-ti-r54 I've tried editing the /boot/uEnv.txt file to disable loading the Cape, but I've always come up with an error. When I disable uboot_overlays and power up my BBB, the user LEDs start blinking but after a few seconds only the heartbeat LED is on, while the other LEDs are off permanently. On the screen I can only see the startup "penguin icon" but it's like the BBB froze. I've also tried uncommenting disable_uboot_overlay_addr0= and enabling uboot_overlays but then the same thing happens to the LEDs while my monitor doesn't even recognize a HDMI device. I am really stuck because I think it has to be possible to disable the Display Cape but I can't figure out how. Thank you in advance. Regards Marco P.S: further information about my BBB output of version.sh: debian@beaglebone:~$ sudo /opt/scripts/tools/version.sh git:/opt/scripts/:[31292bce1d4b35b497cc7a013d6d57e7e1f4f5c4] eeprom:[A335BNLT00C01718BBBK072B] model:[TI_AM335x_BeagleBone_Black] dogtag:[BeagleBoard.org Debian Image 2018-06-17] bootloader:[microSD-(push-button)]:[/dev/mmcblk0]:[U-Boot 2018.03-00002-gac9cce7c6a]:[location: dd MBR] kernel:[4.14.49-ti-r54] nodejs:[v6.14.4] uboot_overlay_options:[enable_uboot_overlays=1] uboot_overlay_options:[uboot_overlay_addr6=/lib/firmware/BB-SPIDEV0-00A0.dtbo] uboot_overlay_options:[uboot_overlay_pru=/lib/firmware/AM335X-PRU-RPROC-4-14-TI-00A0.dtbo] uboot_overlay_options:[enable_uboot_cape_universal=1] pkg check: to individually upgrade run: [sudo apt install --only-upgrade <pkg>] pkg:[bb-cape-overlays]:[4.4.20180914.0-0rcnee0~stretch+20180914] pkg:[bb-wl18xx-firmware]:[1.20180517-0rcnee0~stretch+20180517] pkg:[kmod]:[23-2rcnee1~stretch+20171005] pkg:[roboticscape]:[0.4.4-git20180608.0-0rcnee0~stretch+20180609] pkg:[firmware-ti-connectivity]:[20170823-1rcnee1~stretch+20180328] groups:[debian : debian adm kmem dialout cdrom floppy audio dip video plugdev users systemd-journal i2c bluetooth netdev cloud9ide gpio pwm eqep admin spi tisdk weston-launch xenomai] cmdline:[console=ttyO0,115200n8 bone_capemgr.uboot_capemgr_enabled=1 root=/dev/mmcblk0p1 ro rootfstype=ext4 rootwait coherent_pool=1M net.ifnames=0 quiet] dmesg | grep pinctrl-single [ 1.021968] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 dmesg | grep gpio-of-helper [ 1.023167] gpio-of-helper ocp:cape-universal: ready END -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/beagleboard/c3ff5d69-30b4-42b6-a37a-ebdadf3df54a%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
