Hi Mr. Nelson,
Problem in short
I changed partitioning command but with help,
Here is my sfdisk commad,
#Partition
drive
sfdisk --force --in-order --Linux ${DRIVE} -uM
<<-__EOF__
1,32,C,*
,200,L
,200,L
,,E
,100,L
,60,L
,200,L
,1269,L
,,,-
__EOF__
After above command i sync and flush buffers using blockdev command.
and then run "mdev -s" but
I get following output,
*sfdisk: ERROR: sector 184348 does not have an msdos signature*
sfdisk: /dev/mmcblk0: unrecognized partition table type
Old situation:
sfdisk: No partitions found
New situation:
Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0
Device Boot Start End MiB #blocks Id System
/dev/mmcblk0p1 * 1 32 32 32768 c W95 FAT32 (LBA)
/dev/mmcblk0p2 33 232 200 204800 83 Linux
/dev/mmcblk0p3 233 432 200 204800 83 Linux
/dev/mmcblk0p4 433 3663 3231 3308544 5 Extended
/dev/mmcblk0p5 433+ 532 100- 102399+ 83 Linux
/dev/mmcblk0p6 533+ 592 60- 61439+ 83 Linux
/dev/mmcblk0p7 593+ 792 200- 204799+ 83 Linux
/dev/mmcblk0p8 793+ 2061 1269- 1299455+ 83 Linux
/dev/mmcblk0p9 2062+ 3663 1602- 1640447+ 83 Linux
Successfully wrote the new partition table
Re-reading the partition table ...
If you created or changed a DOS partition, /dev/foo7, say, then use dd(1)
to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512 count=1
(See fdisk(8).)
Auto-mount of [/media/mmcblk0p5] successful
Auto-mount of [/media/mmcblk0p6] successful
Auto-mount of [/media/mmcblk0p7] successful
Auto-mount of [/media/mmcblk0p8] successful
*Error: Error informing the kernel about modifications to partition
/dev/mmcblk0p5 -- Device or resource busy. This means Linux won't know
about any changes you made to /dev/mmcblk0p5 until you reboot -- .*
Error: Failed to add partition 5 (Device or resource busy)
mount: mounting /dev/mmcblk0p1 on /media/mmcblk0p1 failed: Invalid argument
rm: can't remove '/tmp/.automount-mmcblk0p1': No such file or directory
mount: mounting /dev/mmcblk0p2 on /media/mmcblk0p2 failed: Invalid argument
rm: can't remove '/tmp/.automount-mmcblk0p2': No such file or directory
mount: mounting /dev/mmcblk0p3 on /media/mmcblk0p3 failed: Invalid argument
rm: can't remove '/tmp/.automount-mmcblk0p3': No such file or directory
mount: mounting /dev/mmcblk0p4 on /media/mmcblk0p4 failed: Invalid argument
rm: can't remove '/tmp/.automount-mmcblk0p4': No such file or directory
rm: can't remove '/tmp/.automount-mmcblk0p6': No such file or directory
rm: can't remove '/tmp/.automount-mmcblk0p7': No such file or directory
rm: can't remove '/tmp/.automount-mmcblk0p8': No such file or directory
rootfs on / type rootfs (rw)
192.168.1.3:/nfsboot on / type nfs
(rw,relatime,vers=2,rsize=4096,wsize=4096,namlen=255,hard,nolock,proto=udp,timeo=11,retrans=3,sec=sys,mountaddr=192.168.1.3,mountvers=1,mountproto=udp,local_lock=all,add)
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
tmpfs on /tmp type tmpfs (rw,relatime)
none on /dev/pts type devpts (rw,relatime,mode=600)
tmpfs on /dev/shm type tmpfs (rw,relatime,mode=777)
tmpfs on /var/run type tmpfs (rw,relatime,mode=777)
tmpfs on /var/spool/cron type tmpfs (rw,relatime,mode=755)
tmpfs on /var/sftp type tmpfs (rw,relatime,mode=755)
+ sfdisk -R /dev/mmcblk0
+
+ [ 0 -ne 0 ]
+ echo Nothing is mounted on /dev/mmcblk0
Nothing is mounted on /dev/mmcblk0
+ RETRY=50
+ NO_OF_PARTITIONS=2
+ 2 -ne 10
./BAK_S99-flashfirmware: line 1: 2: not found
+ set +x
mke2fs 1.42.8 (20-Jun-2013)
Discarding device blocks: done
Auto-mount of [/media/mmcblk0p6] successful
Auto-mount of [/media/mmcblk0p7] successful
Auto-mount of [/media/mmcblk0p5] successful
Filesystem label=rootfs
I checked /sys/class/block directory and i see following,
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop0 ->
../../devices/virtual/block/loop0
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop1 ->
../../devices/virtual/block/loop1
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop2 ->
../../devices/virtual/block/loop2
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop3 ->
../../devices/virtual/block/loop3
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop4 ->
../../devices/virtual/block/loop4
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop5 ->
../../devices/virtual/block/loop5
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop6 ->
../../devices/virtual/block/loop6
lrwxrwxrwx 1 root root 0 Dec 31 19:00 loop7 ->
../../devices/virtual/block/loop7
*lrwxrwxrwx 1 root root 0 Dec 31 19:00 mmcblk0 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0lrwxrwxrwx
1 root root 0 Dec 31 19:00 mmcblk0boot0 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0boot0lrwxrwxrwx
1 root root 0 Dec 31 19:00 mmcblk0boot1 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0boot1lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p1 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p1lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p2 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p2lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p3 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p3lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p4 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p4lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p5 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p5lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p6 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p6lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p7 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p7lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p8 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p8lrwxrwxrwx
1 root root 0 Dec 31 19:12 mmcblk0p9 ->
../../devices/ocp.2/481d8000.mmc/mmc_host/mmc1/mmc1:0001/block/mmcblk0/mmcblk0p9*
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram0 ->
../../devices/virtual/block/ram0
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram1 ->
../../devices/virtual/block/ram1
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram10 ->
../../devices/virtual/block/ram10
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram11 ->
../../devices/virtual/block/ram11
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram12 ->
../../devices/virtual/block/ram12
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram13 ->
../../devices/virtual/block/ram13
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram14 ->
../../devices/virtual/block/ram14
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram15 ->
../../devices/virtual/block/ram15
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram2 ->
../../devices/virtual/block/ram2
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram3 ->
../../devices/virtual/block/ram3
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram4 ->
../../devices/virtual/block/ram4
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram5 ->
../../devices/virtual/block/ram5
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram6 ->
../../devices/virtual/block/ram6
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram7 ->
../../devices/virtual/block/ram7
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram8 ->
../../devices/virtual/block/ram8
lrwxrwxrwx 1 root root 0 Dec 31 19:00 ram9 ->
../../devices/virtual/block/ram9
Can we conclude that from mmc driverside there is problem.
Do you doubt mdev ??
Can network boot affect ? I am booting from network to update eMMC.
Thank you,
Regards,
Ankur
On Friday, 24 April 2015 21:57:07 UTC+5:30, RobertCNelson wrote:
>
> On Fri, Apr 24, 2015 at 11:22 AM, Ankur Tank <art...@gmail.com
> <javascript:>> wrote:
> > Problem in short:
> > eMMC partition's device files are not visible in /dev/ directory after
> > partitiong using "sfdisk"
> > HI ,
> >
> > I have put log of script here, any suggestions,
> >
> > + partition_emmc /dev/mmcblk0
> > + DRIVE=/dev/mmcblk0
> > + HEADS=255
> > + SECTOR_SIZE=512
> > + SECTORS_PER_TRACK=63
> > + dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=108
> > 108+0 records in
> > 108+0 records out
> > + sync
> > + dd if=/dev/mmcblk0 of=/dev/null bs=1M count=108
> > 108+0 records in
> > 108+0 records out
> > + sync
> > + blockdev --flushbufs /dev/mmcblk0
> > + + grepgrep+ bytes Disk
> >
> > fdisk -l /dev/mmcblk0
> > + awk {print $5}
> > + SIZE=3841982464
> > + echo DISK SIZE - 3841982464 bytes
> > DISK SIZE - 3841982464 bytes
> > + echo 3841982464 255 / 63 / 512 / p
> > + dc
> > + CYLINDERS=467.094
> > + echo CYLINDERS - 467.094
> > CYLINDERS - 467.094
> > + sfdisk -R /dev/mmcblk0
> > BLKRRPART: Device or resource busy
> > sfdisk: This disk is currently in use.
> >
> > +
> > + [ 1 -ne 0 ]
> > + + + grepawk /dev/mmcblk0 {print $3}
> >
> > mount
> > + mntpoint=/media/mmcblk0p8
> > /media/mmcblk0p6
> > /media/mmcblk0p7
> > /media/mmcblk0p5
> > + echo unmounting /media/mmcblk0p8
> > unmounting /media/mmcblk0p8
> > + umount /media/mmcblk0p8
> > + echo unmounting /media/mmcblk0p6
> > unmounting /media/mmcblk0p6
> > + umount /media/mmcblk0p6
> > + echo unmounting /media/mmcblk0p7
> > unmounting /media/mmcblk0p7
> > + umount /media/mmcblk0p7
> > + echo unmounting /media/mmcblk0p5
> > unmounting /media/mmcblk0p5
> > + umount /media/mmcblk0p5
> > + sfdisk --force --in-order --Linux -H 255 -S 63 -C 467.094 /dev/mmcblk0
> -uM
> > Checking that no-one is using this disk right now ...
> > OK
> >
> > Disk /dev/mmcblk0: 467 cylinders, 255 heads, 63 sectors/track
> >
> > sfdisk: ERROR: sector 184348 does not have an msdos signature
> > sfdisk: /dev/mmcblk0: unrecognized partition table type
> >
> > Old situation:
> > sfdisk: No partitions found
> >
> > New situation:
> > Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from
> 0
> >
> > Device Boot Start End MiB #blocks Id System
> > /dev/mmcblk0p1 * 0+ 31 32- 32767+ c W95 FAT32 (LBA)
> > /dev/mmcblk0p2 32 231 200 204800 83 Linux
> > /dev/mmcblk0p3 232 431 200 204800 83 Linux
> > /dev/mmcblk0p4 432 3663 3232 3309568 5 Extended
> > /dev/mmcblk0p5 432+ 531 100- 102399+ 83 Linux
> > /dev/mmcblk0p6 532+ 591 60- 61439+ 83 Linux
> > /dev/mmcblk0p7 592+ 791 200- 204799+ 83 Linux
> > /dev/mmcblk0p8 792+ 2060 1269- 1299455+ 83 Linux
> > /dev/mmcblk0p9 2061+ 3663 1603- 1641471+ 83 Linux
> > Successfully wrote the new partition table
> >
> > Re-reading the partition table ...
> >
> > If you created or changed a DOS partition, /dev/foo7, say, then use
> dd(1)
> > to zero the first 512 bytes: dd if=/dev/zero of=/dev/foo7 bs=512
> count=1
> > (See fdisk(8).)
> > + sync
> > + blockdev --flushbufs /dev/mmcblk0
> > + partprobe
> > Auto-mount of [/media/mmcblk0p5] successful
> > Auto-mount of [/media/mmcblk0p6] successful
> > Auto-mount of [/media/mmcblk0p7] successful
> > Auto-mount of [/media/mmcblk0p8] successful
> > Error: Error informing the kernel about modifications to partition
> > /dev/mmcblk0p5 -- Device or r.
> > Error: Failed to add partition 5 (Device or resource busy)
> > + rm -rf /tmp/.a*
> > + mdev -s
> > mount: mounting /dev/mmcblk0p1 on /media/mmcblk0p1 failed: Invalid
> argument
> > rm: can't remove '/tmp/.automount-mmcblk0p1': No such file or directory
> > mount: mounting /dev/mmcblk0p2 on /media/mmcblk0p2 failed: Invalid
> argument
> > rm: can't remove '/tmp/.automount-mmcblk0p2': No such file or directory
> > mount: mounting /dev/mmcblk0p3 on /media/mmcblk0p3 failed: Invalid
> argument
> > rm: can't remove '/tmp/.automount-mmcblk0p3': No such file or directory
> > mount: mounting /dev/mmcblk0p4 on /media/mmcblk0p4 failed: Invalid
> argument
> > rm: can't remove '/tmp/.automount-mmcblk0p4': No such file or directory
> > rm: can't remove '/tmp/.automount-mmcblk0p7': No such file or directory
> > rm: can't remove '/tmp/.automount-mmcblk0p8': No such file or directory
> > + sync
> > + blockdev --flushbufs /dev/mmcblk0
> > + mount
> > rootfs on / type rootfs (rw)
> > 192.168.1.3:/nfsboot on / type nfs
> > (rw,relatime,vers=2,rsize=4096,wsize=4096,namlen=255,hard,nol)
> > proc on /proc type proc (rw,relatime)
> > sysfs on /sys type sysfs (rw,relatime)
> > tmpfs on /tmp type tmpfs (rw,relatime)
> > none on /dev/pts type devpts (rw,relatime,mode=600)
> > tmpfs on /dev/shm type tmpfs (rw,relatime,mode=777)
> > tmpfs on /var/run type tmpfs (rw,relatime,mode=777)
> > tmpfs on /var/spool/cron type tmpfs (rw,relatime,mode=755)
> > tmpfs on /var/sftp type tmpfs (rw,relatime,mode=755)
> > + sfdisk -R /dev/mmcblk0
> > +
> > + [ 0 -ne 0 ]
> > + echo Nothing is mounted on /dev/mmcblk0
> > Nothing is mounted on /dev/mmcblk0
> > + RETRY=50
> > + NO_OF_PARTITIONS=2
> > + 2 != 10
> > ./BAK_S99-flashfirmware: line 1: 2: not found
> > + check_and_format_partition /dev/mmcblk0p2 rootfs
> > + PARTITION=/dev/mmcblk0p2
> > + LABEL=rootfs
> > + MNTPNT=0
> > + mount
> > + grep /dev/mmcblk0p2
> > + awk {print $3}
> > + MNTPNT=
> > + [ -n ]
> > + [ -b /dev/mmcblk0p2 ]
> > + mkfs.ext4 -L rootfs /dev/mmcblk0p2
> > mke2fs 1.42.8 (20-Jun-2013)
> > Auto-mount of [/media/mmcblk0p5] successful
> > mkfs.ext4: No such file or directory while trying to determine hardware
> > sector size
> > + check_and_format_partition /dev/mmcblk0p3 rootfs2
> > + PARTITION=/dev/mmcblk0p3
> > + LABEL=rootfs2
> > + MNTPNT=0
> > + mount
> > + grep+ awk /dev/mmcblk0p3
> > {print $3}
> > Auto-mount of [/media/mmcblk0p8] successful
> > + MNTPNT=
> > + [ -n ]
> > + [ -b /dev/mmcblk0p3 ]
> > + echo Cant find /dev/mmcblk0p3 partition
> > Cant find /dev/mmcblk0p3 partition
> > + check_and_format_partition /dev/mmcblk0p5 recovery_rootfs
> > + PARTITION=/dev/mmcblk0p5
> > + LABEL=recovery_rootfs
> > + MNTPNT=0
> > + mount
> > + grep /dev/mmcblk0p5+ awk {print $3}
> >
> > + MNTPNT=/media/mmcblk0p5
> > + [ -n /media/mmcblk0p5 ]
> > + echo /dev/mmcblk0p5 is mounted on /media/mmcblk0p5
> > /dev/mmcblk0p5 is mounted on /media/mmcblk0p5
> > + [ -b /dev/mmcblk0p5 ]
> > + echo Cant find /dev/mmcblk0p5 partition
> > Cant find /dev/mmcblk0p5 partition
> > + check_and_format_partition /dev/mmcblk0p6 database
> > + PARTITION=/dev/mmcblk0p6
> > + LABEL=database
> > + MNTPNT=0
> > + mount
> > + grep /dev/mmcblk0p6
> > + awk {print $3}
> > Auto-mount of [/media/mmcblk0p7] successful
> > + MNTPNT=
> > + [ -n ]
> > + [ -b /dev/mmcblk0p6 ]
> > + mkfs.ext4 -L database /dev/mmcblk0p6
> > Auto-mount of [/media/mmcblk0p6] successful
> > mke2fs 1.42.8 (20-Jun-2013)
> > /dev/mmcblk0p6 is mounted; will not make a filesystem here!
> > + check_and_format_partition /dev/mmcblk0p7 firmware
> > + PARTITION=/dev/mmcblk0p7
> > + LABEL=firmware
> > + MNTPNT=0
> > + grep /dev/mmcblk0p7
> > + mount
> > + awk {print $3}
> > + MNTPNT=/media/mmcblk0p7
> > + [ -n /media/mmcblk0p7 ]
> > + echo /dev/mmcblk0p7 is mounted on /media/mmcblk0p7
> > /dev/mmcblk0p7 is mounted on /media/mmcblk0p7
> > + [ -b /dev/mmcblk0p7 ]
> > + mkfs.ext4 -L firmware /dev/mmcblk0p7
> > mke2fs 1.42.8 (20-Jun-2013)
> > /dev/mmcblk0p7 is mounted; will not make a filesystem here!
> > + check_and_format_partition /dev/mmcblk0p8 logging
> > + PARTITION=/dev/mmcblk0p8
> > + LABEL=logging
> > + MNTPNT=0
> > + grep /dev/mmcblk0p8
> > + awk {print $3}
> > + mount
> > + MNTPNT=/media/mmcblk0p8
> > + [ -n /media/mmcblk0p8 ]
> > + echo /dev/mmcblk0p8 is mounted on /media/mmcblk0p8
> > /dev/mmcblk0p8 is mounted on /media/mmcblk0p8
> > + [ -b /dev/mmcblk0p8 ]
> > + echo Cant find /dev/mmcblk0p8 partition
> > Cant find /dev/mmcblk0p8 partition
> > + sed -r s/://g
> > + cat /sys/class/net/eth0/address
> > + MACADDRESS=7c669d19cce2
> > + BASE_MOUNT_POINT=/mnt/7c669d19cce2
> > + ROOTFS_MOUNT=/mnt/7c669d19cce2/rootfs
> > + ROOTFS2_MOUNT=/mnt/7c669d19cce2/rootfs2
> > + ROOTFS_RECOVERY_MOUNT=/mnt/7c669d19cce2/recovery_rootfs
> > + DB_MOUNT=/mnt/7c669d19cce2/database
> > + FIRMWARE_MOUNT=/mnt/7c669d19cce2/firmware
> > + LOGGING_MOUNT=/mnt/7c669d19cce2/logging
> > + echoAndLog mount all the partitions
> > + echo mount all the partitions
> > mount all the partitions
> > + logger -p 5 -t ./BAK_S99-flashfirmware mount all the partitions
> > + [ ! -d /mnt/7c669d19cce2/rootfs ]
> > + [ ! -d /mnt/7c669d19cce2/rootfs2 ]
> > + [ ! -d /mnt/7c669d19cce2/recovery_rootfs ]
> > + [ ! -d /mnt/7c669d19cce2/database ]
> > + RETRY=50
> > + [ 50 -ne 0 ]
> > + [ ! -b /dev/mmcblk0p2 ]
> > + echo ....Waiting till /dev/mmcblk0p2 appears retry=50
> > ....Waiting till /dev/mmcblk0p2 appears retry=50
> >
> > Anything fishy ?? If same partitioning command i run from command prompt
> it
> > works but not from script do you suggestion anything ?
> >
> > Script looks as show below..
> >
> > DRIVE="/dev/mmcblk0"
> > RFS1_PARTITION=${DRIVE}p2
> > RFS2_PARTITION=${DRIVE}p3
> > RECOVERYRFS_PARTITION=${DRIVE}p5
> > DATABASE_PARTITION=${DRIVE}p6
> > FIRMWARE_PARTITION=${DRIVE}p7
> > LOGGING_PARTITION=${DRIVE}p8
> >
> > partition_emmc()
> > {
> > DRIVE=$1
> > HEADS=255
> > SECTOR_SIZE=512
> > SECTORS_PER_TRACK=63
> >
> > #Clear the first 512KB of the disk to clear MBR
> > dd if=/dev/zero of=${DRIVE} bs=1M count=108
> > sync
> > dd if=${DRIVE} of=/dev/null bs=1M count=108
> > sync
> > blockdev --flushbufs ${DRIVE}
> >
> > #Get the size of the disk
> > SIZE=$(fdisk -l $DRIVE | grep "Disk" | grep bytes | awk '{print
> > $5}')
> > echo "DISK SIZE - $SIZE bytes"
> >
> > #calculate the no of cylinders in the disk
> > CYLINDERS=$(echo "$SIZE $HEADS / $SECTORS_PER_TRACK /
> $SECTOR_SIZE /
> > p" | dc )
> > echo "CYLINDERS - $CYLINDERS"
> >
> > #Check if any of the partition is mounted, umount it if mounted.
> > $(sfdisk -R ${DRIVE})
> > if [ $? -ne 0 ];then
> > mntpoint=$(mount | grep ${DRIVE} | awk '{print $3}')
> > for i in $mntpoint ; do
> > echo "unmounting $i"
> > umount $i
> > done
> > else
> > echo "Nothing is mounted on ${DRIVE}"
> > fi
> >
> > #Partition drive
> > # sfdisk --force --in-order --Linux -H 255 -S 63 -C $CYLINDERS
> > ${DRIVE} -uM <<-__EOF__
> > sfdisk --force --in-order --Linux -H 255 -S 63 -C 467 ${DRIVE}
> -uM
> > <<-__EOF__
>
> Stop with all the cylinders crap, it's not 2009 anymore and we "fixed"
> x-loader/u-boot spl, with the boot from "63" location "years" ago...
>
> > ,32,C,*
> 1,32,C,* (now you have a 1Mb hole, which will work with
> the bootloader..)
>
> > ,200,L
> > ,200,L
> > ,,E
> > ,100,L
> > ,60,L
> > ,200,L
> > ,1269,L
> > ,,,-
> > __EOF__
> >
> > }
> >
> > # arg1 = partition
> > # arg2 = label
> > check_and_format_partition()
> > {
> > PARTITION=$1
> > LABEL=$2
> > MNTPNT=0
> > MNTPNT=$(mount | grep $PARTITION | awk '{print $3}')
> > if [ -n "$MNTPNT" ]; then
> > echo "$PARTITION is mounted on $MNTPNT"
> > fi
> > if [ -b $PARTITION ]; then
> > mkfs.ext4 -L $LABEL $PARTITION
> > #TODO : Find correct tunning parameter and set it.
> > #tune2fs
> > else
> > echo "Cant find $PARTITION partition"
> > fi
> > }
> >
> > #Partition the eMMC
> > partition_emmc $DRIVE
> >
> > sync
> > blockdev --flushbufs $DRIVE
> >
> > partprobe
> > rm -rf /tmp/.a*
> >
> > #Trigger the creation of the device files
> > mdev -s
> > sync
> > blockdev --flushbufs $DRIVE
> >
> > mount
> >
> > $(sfdisk -R ${DRIVE})
> > if [ $? -ne 0 ]; then
> > mntpoint=$(mount | grep ${DRIVE} | awk '{print $3}')
> > for i in $mntpoint ; do
> > echo "unmounting $i"
> > umount $i
> > done
> > else
> > echo "Nothing is mounted on ${DRIVE}"
> > fi
> >
> > #Wait till mmcblk0pX partitions are available.
> > RETRY=50
> > NO_OF_PARTITIONS=2
> > while (( $NO_OF_PARTITIONS != 10 )); do
> >
> > while (( [ $RETRY -ne 0 ] && [ ! -b "${DRIVE}p$i" ] )); do
> > echo "....Waiting till $RFS1_PARTITION appears"
> > RETRY=`expr $RETRY - 1`
> > sleep 1
> > done
> >
> > if [ $RETRY -eq 0 ];then
> > echo "Error..Device files are not present"
> > exit 1;
> > fi
> > NO_OF_PARTITIONS=`expr NO_OF_PARTITIONS + 1`
> > done
> >
> > #Format the partitions
> > check_and_format_partition $RFS1_PARTITION $RFS_STRING
> > check_and_format_partition $RFS2_PARTITION $RFS2_STRING
> > check_and_format_partition $RECOVERYRFS_PARTITION
> $RFS_RECOVERY_STRING
> > check_and_format_partition $DATABASE_PARTITION $DATABASE_STRING
> > check_and_format_partition $FIRMWARE_PARTITION $FIRMWARE_STRING
> > check_and_format_partition $LOGGING_PARTITION $LOGGING_STRING
> >
> > MACADDRESS=`cat /sys/class/net/eth0/address | sed -r 's/://g'`
> > BASE_MOUNT_POINT=/mnt/$MACADDRESS
> > ROOTFS_MOUNT=$BASE_MOUNT_POINT/rootfs
> > ROOTFS2_MOUNT=$BASE_MOUNT_POINT/rootfs2
> > ROOTFS_RECOVERY_MOUNT=$BASE_MOUNT_POINT/recovery_rootfs
> > DB_MOUNT=$BASE_MOUNT_POINT/database
> > FIRMWARE_MOUNT=$BASE_MOUNT_POINT/firmware
> > LOGGING_MOUNT=$BASE_MOUNT_POINT/logging
> >
> > echoAndLog "mount all the partitions"
> > #Create mount point if it doesn't exist.
> > if [ ! -d "$ROOTFS_MOUNT" ]; then
> > mkdir -p $ROOTFS_MOUNT
> > fi
> > if [ ! -d "$ROOTFS2_MOUNT" ]; then
> > mkdir -p $ROOTFS2_MOUNT
> > fi
> > if [ ! -d "$ROOTFS_RECOVERY_MOUNT" ]; then
> > mkdir -p $ROOTFS_RECOVERY_MOUNT
> > fi
> > if [ ! -d "$DB_MOUNT" ]; then
> > mkdir -p $DB_MOUNT
> > fi
> >
> >
> >
> > }
> >
>
>
> Regards,
>
> --
> Robert Nelson
> https://rcn-ee.com/
>
--
For more options, visit http://beagleboard.org/discuss
---
You received this message because you are subscribed to the Google Groups
"BeagleBoard" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to beagleboard+unsubscr...@googlegroups.com.
For more options, visit https://groups.google.com/d/optout.
