Hello Steve,
I think this may help you to disable linux multipathing for the tape
library:
http://thegeekdiary.com/beginners-guide-to-device-mapper-dm-multipathing/
The tape library and tape drive can be configured in the black list:
blacklist Blacklisted devies. Devices that should not be configured under
DMMP
Once you have your tape library/drive not using linux multipath, everything
should run fine with your Bacula configurations using the "/dev/tape/by-id"
device name.
Hope this helps.
Best regards,
Ana
On Wed, Aug 2, 2017 at 2:07 PM, Steve Garcia <sgar...@bak.rr.com> wrote:
>
>
>
> ---- "Ana Emília M. Arruda" <emiliaarr...@gmail.com> wrote:
> > Hello Steve,
> >
> > Sorry, incomplete email again...
> >
> > Yes, it looks we have something here.
> >
> > From one of your previous emails, we have the error "3999 Device
> > "AutochangerOdin" not found or could not be opened." when Bacula issues
> the
> > label command for the tapes.
> >
> > This "not found or could not be opened" message usually refers to the
> wrong
> > "device name" configured for an "Archive Device" or "Changer Device".
> >
> > The below two messages in the debug output also indicates this problem:
> > odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0 got=0
> > skipping
> >
> > From another post, you have only one tape library with one tape drive,
> but
> > two paths for each of them:
> >
> > root@odin:/etc/bacula# lsscsi -g
> > [0:2:0:0] disk DELL PERC H730 Mini 4.27 /dev/sda /dev/sg0
> > [1:0:0:0] tape IBM ULT3580-HH6 G9P1 /dev/st0 /dev/sg2
> > [1:0:0:1] mediumx IBM 3573-TL E.30 /dev/sch0 /dev/sg3
> > [1:0:1:0] tape IBM ULT3580-HH6 G9P1 /dev/st1 /dev/sg4
> > [1:0:1:1] mediumx IBM 3573-TL E.30 /dev/sch1 /dev/sg5
> > [6:2:0:0] disk DELL PERC H830 Adp 4.27 /dev/sdb /dev/sg1
> > [12:0:0:0] cd/dvd PLDS DVD-ROM DS-8DBSH MD52 /dev/sr0 /dev/sg6
> >
> > This seems to me you have a tape library/drive configured with physical
> > multipath (zoning, two HBAs, etc.) for fail over?
>
> Well, this machine *does* have physical multipathing, but not for the
> library or tape drive. The PERC H830 listed above is a single HBA/RAID
> controller, but with two interfaces that go to separate controllers on my
> disk array. Multipath is configured for the system, but only intended for
> the disk array.
>
> The library is connected to a different HBA (which apparently doesn't rate
> an entry in the above table, being a simple SCSI HBA) which also has two
> interfaces. One goes to the tape drive and one to the changer, so there is
> no actual physical multipath in that chain.
>
> Is it possible that having the multipath libraries loaded could be
> confusing the system about the tape path? I can't get rid of the
> multipath, but maybe there is a way to exclude the tape systems?
>
> Redefining the tape to its by-path designation doesn't look like it will
> work:
>
> 02-Aug 09:59 bacula-sd: ERROR TERMINATION at parse_conf.c:393
> Config error: Attempt to redefine "ArchiveDevice" from
> "/dev/tape/by-id/scsi-35000e11164c42001-nst" to
> "/dev/tape/by-path/pci-0000:05:00.0-sas-phy2-lun-0-nst" referenced on
> line 78 : Archive Device = /dev/tape/by-path/pci-0000:05:
> 00.0-sas-phy2-lun-0-nst
>
>
> : line 78, col 72 of file /etc/bacula/bacula-sd.conf
> Archive Device = /dev/tape/by-path/pci-0000:05:00.0-sas-phy2-lun-0-nst
>
> > If so, you don't have multipath configured in this linux system? This
> > explains that your system sees two different device names for each one of
> > your tape library and tape drive.
> >
> > If this is the case, I'm afraid you will have problems to use the
> > "/dev/tape/by-id" or "/dev/nst" device names for the tape drives. Maybe
> it
> > would be better, in this case, to use "/dev/tape/by-path". Even better,
> to
> > not have this physical multipath if you are not going to use it with the
> > tape library...
> >
> > Hope this helps.
> >
> > Best regards,
> > Ana
> >
> >
> > On Tue, Aug 1, 2017 at 9:56 PM, Ana Emília M. Arruda <
> emiliaarr...@gmail.com
> > > wrote:
> >
> > > Hello Steve,
> > >
> > > Yes, it looks we have something here.
> > >
> > > From one of your previous emails, we have the error "3999 Device
> > > "AutochangerOdin" not found or could not be opened." when Bacula
> issues the
> > > label command for the tapes.
> > >
> > > This "not found or could not be opened" message usually refers to the
> > > wrong "device name" configured for an "Archive Device" or "Changer
> Device".
> > >
> > > From another post, you have only one tape library with one tape drive,
> but
> > > two paths for each of them:
> > >
> > >
> > >
> > > On Mon, Jul 31, 2017 at 5:22 PM, Steve Garcia <sgar...@bak.rr.com>
> wrote:
> > >
> > >>
> > >> OK, now we may be getting somewhere -- at least I have a dump of
> > >> messages...
> > >>
> > >> It does look like the problem is with the tape drive, but that's
> after it
> > >> working fine at first. It successfully opens the drive and determines
> > >> (correctly) that the volume in the drive is an unlabeled tape. As a
> > >> result? the tape drive is opened in a read-only state -- or maybe
> that's
> > >> because it start by trying to read the existing label and you only
> need
> > >> read-only for that.
> > >>
> > >> # sudo -u bacula -g tape /usr/sbin/bacula-sd -d200
> > >> bacula-sd: address_conf.c:274-0 Initaddr 0.0.0.0:9103
> > >> bacula-sd: stored_conf.c:698-0 Inserting Director res: sleipnir-mon
> > >> root@odin:/etc/bacula# odin-sd: bsys.c:726-0 Could not open state
> file.
> > >> sfd=-1 size=192: ERR=No such file or directory
> > >> odin-sd: stored.c:572-0 calling init_dev
> /dev/tape/by-id/scsi-35000e111
> > >> 64c42001-nst
> > >> odin-sd: dev.c:342-0 init_dev: tape=1 dev_name=/dev/tape/by-id/scsi-
> > >> 35000e11164c42001-nst
> > >> odin-sd: stored.c:574-0 SD init done /dev/tape/by-id/scsi-35000e111
> > >> 64c42001-nst
> > >> odin-sd: block_util.c:206-0 empty len=64512 block=7fe350002170 set
> > >> binbuf=24
> > >> odin-sd: block_util.c:143-0 New block len=64512 block=7fe350002170
> > >> odin-sd: bnet_server.c:86-0 Addresses 136.168.201.110:9103
> > >> odin-sd: acquire.c:673-0 Attach 0x50001c68 to dev "Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst)
> > >> odin-sd: autochanger.c:322-0 Locking changer AutochangerOdin
> > >> odin-sd: autochanger.c:278-0 Run program=/etc/bacula/scripts/
> mtx-changer
> > >> /dev/tape/by-id/scsi-1IBM_3573-TL_00X2U78BZ022_LL0 loaded 0
> > >> /dev/tape/by-id/scsi-35000e11164c42001-nst 0
> > >> odin-sd: autochanger.c:280-0 run_prog: /etc/bacula/scripts/mtx-
> changer
> > >> /dev/tape/by-id/scsi-1IBM_3573-TL_00X2U78BZ022_LL0 loaded 0
> > >> /dev/tape/by-id/scsi-35000e11164c42001-nst 0 stat=0 result=1
> > >> odin-sd: autochanger.c:336-0 Unlocking changer AutochangerOdin
> > >> odin-sd: stored.c:588-0 calling first_open_device "Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst)
> > >> odin-sd: device.c:279-0 start open_output_device()
> > >> odin-sd: device.c:298-0 Opening device.
> > >> odin-sd: tape_dev.c:958-0 Enter tape mount
> > >> odin-sd: tape_dev.c:84-0 Open dev: device is tape
> > >> odin-sd: autochanger.c:260-0 Return cached slot=1
> > >> odin-sd: tape_dev.c:99-0 Try open "Drive-1" (/dev/tape/by-id/scsi-
> 35000e11164c42001-nst)
> > >> mode=OPEN_READ_ONLY
> > >> odin-sd: tape_dev.c:121-0 Rewind after open
> > >> odin-sd: os.c:58-0 In set_os_device_parameters
> > >> odin-sd: os.c:64-0 Set block size to zero
> > >> odin-sd: tape_dev.c:176-0 open dev: tape 5 opened
> > >> odin-sd: dev.c:391-0 preserve=0x0 fd=5
> > >> odin-sd: dev.c:394-0 open dev: fd=5 dev=7fe350001476 dcr=7fe350001098
> > >> vol= type=2 dev_name="Drive-1" (/dev/tape/by-id/scsi-
> 35000e11164c42001-nst)
> > >> mode=OPEN_READ_ONLY
> > >> odin-sd: device.c:304-0 open dev "Drive-1" (/dev/tape/by-id/scsi-
> 35000e11164c42001-nst)
> > >> OK
> > >> odin-sd: label.c:72-0 Enter: int read_dev_volume_label(DCR*)
> > >> odin-sd: label.c:75-0 Enter read_volume_label res=0 device="Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst) vol= dev_Vol=*NULL*
> > >> odin-sd: block_util.c:206-0 empty len=64512 block=7fe350002170 set
> > >> binbuf=24
> > >> odin-sd: label.c:126-0 Big if statement in read_volume_label
> > >> odin-sd: block.c:458-0 Read() vol= nbytes=0 addr=-1
> > >> odin-sd: block.c:487-0 block.c:480 The Volume= on device="Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst) appears to be unlabeled.
> > >> odin-sd: block.c:493-0 ==== Read zero bytes. vol= at -1
> > >> odin-sd: label.c:131-0 Requested Volume "" on tape device "Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst) is not a Bacula labeled
> > >> Volume, because: ERR=block.c:480 The Volume= on device="Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst) appears to be unlabeled.
> > >> odin-sd: label.c:160-0 No volume label - bailing out
> > >> odin-sd: block_util.c:206-0 empty len=64512 block=7fe350002170 set
> > >> binbuf=24
> > >> odin-sd: label.c:251-0 return 3
> > >> odin-sd: label.c:252-0 Leave: int read_dev_volume_label(DCR*)
> > >> odin-sd: stored.c:613-0 Could not mount device "Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst)
> > >> odin-sd: bnet.c:566-0 who=client host=136.168.201.100 port=9103
> > >> odin-sd: dircmd.c:178-0 Got a DIR connection at 31-Jul-2017 12:58:24
> > >> odin-sd: cram-md5.c:69-0 send: auth cram-md5 challenge
> > >> <1587823263.1501531104@odin-sd> ssl=0
> > >> odin-sd: cram-md5.c:133-0 cram-get received: auth cram-md5
> > >> <839623232.1501531104@sleipnir-dir> ssl=0
> > >> odin-sd: cram-md5.c:157-0 sending resp to challenge:
> > >> P7tmG2+KsR/8M7YfplspnD
> > >> odin-sd: dircmd.c:204-0 Message channel init completed.
> > >> odin-sd: dircmd.c:211-0 <dird: autochanger slots AutochangerOdin
> > >>
> > >> odin-sd: dircmd.c:225-0 Do command: autochanger
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:837-0 Found changer device Drive-1
> > >> odin-sd: dircmd.c:850-0 Found device Drive-1
> > >> odin-sd: block_util.c:206-0 empty len=64512 block=7fe350012830 set
> > >> binbuf=24
> > >> odin-sd: block_util.c:143-0 New block len=64512 block=7fe350012830
> > >> odin-sd: acquire.c:673-0 Attach 0x50012f38 to dev "Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst)
> > >> odin-sd: autochanger.c:322-0 Locking changer AutochangerOdin
> > >> odin-sd: autochanger.c:670-0 <stored: slots=24
> > >> odin-sd: autochanger.c:336-0 Unlocking changer AutochangerOdin
> > >> odin-sd: bnet.c:566-0 who=client host=136.168.201.100 port=9103
> > >> odin-sd: dircmd.c:178-0 Got a DIR connection at 31-Jul-2017 12:58:25
> > >> odin-sd: cram-md5.c:69-0 send: auth cram-md5 challenge
> > >> <1792316614.1501531105@odin-sd> ssl=0
> > >> odin-sd: cram-md5.c:133-0 cram-get received: auth cram-md5
> > >> <1290223807.1501531105@sleipnir-dir> ssl=0
> > >> odin-sd: cram-md5.c:157-0 sending resp to challenge:
> > >> u+RSe94jz4UptzNhM8+toC
> > >> odin-sd: dircmd.c:204-0 Message channel init completed.
> > >> odin-sd: dircmd.c:211-0 <dird: autochanger list AutochangerOdin
> > >>
> > >> odin-sd: dircmd.c:225-0 Do command: autochanger
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:837-0 Found changer device Drive-1
> > >> odin-sd: dircmd.c:850-0 Found device Drive-1
> > >> odin-sd: block_util.c:206-0 empty len=64512 block=7fe348001500 set
> > >> binbuf=24
> > >> odin-sd: block_util.c:143-0 New block len=64512 block=7fe348001500
> > >> odin-sd: acquire.c:673-0 Attach 0x48000ff8 to dev "Drive-1"
> > >> (/dev/tape/by-id/scsi-35000e11164c42001-nst)
> > >> odin-sd: autochanger.c:322-0 Locking changer AutochangerOdin
> > >> odin-sd: autochanger.c:278-0 Run program=/etc/bacula/scripts/
> mtx-changer
> > >> /dev/tape/by-id/scsi-1IBM_3573-TL_00X2U78BZ022_LL0 loaded 0
> > >> /dev/tape/by-id/scsi-35000e11164c42001-nst 0
> > >> odin-sd: autochanger.c:280-0 run_prog: /etc/bacula/scripts/mtx-
> changer
> > >> /dev/tape/by-id/scsi-1IBM_3573-TL_00X2U78BZ022_LL0 loaded 0
> > >> /dev/tape/by-id/scsi-35000e11164c42001-nst 0 stat=0 result=1
> > >> odin-sd: autochanger.c:336-0 Unlocking changer AutochangerOdin
> > >> odin-sd: autochanger.c:322-0 Locking changer AutochangerOdin
> > >> odin-sd: autochanger.c:657-0 <stored: 2:000018L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 3:000021L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 4:CLNU00L1
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 5:000014L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 6:000017L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 7:000020L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 8:CLN005L3
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 9:000013L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 10:000016L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 11:000019L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 12:000012L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 13:000009L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 14:000006L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 15:000003L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 16:000011L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 17:000008L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 18:000005L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 19:000002L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 20:000010L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 21:000007L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 22:000004L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 23:000001L6
> > >>
> > >> odin-sd: autochanger.c:657-0 <stored: 1:000015L6
> > >>
> > >>
> > >> odin-sd: autochanger.c:336-0 Unlocking changer AutochangerOdin
> > >> odin-sd: bnet.c:566-0 who=client host=136.168.201.100 port=9103
> > >> odin-sd: dircmd.c:178-0 Got a DIR connection at 31-Jul-2017 12:58:35
> > >> odin-sd: cram-md5.c:69-0 send: auth cram-md5 challenge
> > >> <1434613563.1501531115@odin-sd> ssl=0
> > >> odin-sd: cram-md5.c:133-0 cram-get received: auth cram-md5
> > >> <734308377.1501531115@sleipnir-dir> ssl=0
> > >> odin-sd: cram-md5.c:157-0 sending resp to challenge:
> > >> GA/q4g/uIH/DvkJfC/+UwA
> > >> odin-sd: dircmd.c:204-0 Message channel init completed.
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000015L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=1 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000018L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=2 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000021L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=3 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000014L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=5 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000017L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=6 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000020L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=7 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000013L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=9 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000016L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=10 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000019L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=11 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000012L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=12 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000009L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=13 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000006L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=14 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000003L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=15 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000011L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=16 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000008L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=17 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000005L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=18 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000002L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=19 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000010L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=20 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000007L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=21 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000004L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=22 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >> odin-sd: dircmd.c:211-0 <dird: label AutochangerOdin
> VolumeName=000001L6
> > >> PoolName=OdinPool MediaType=LTO6 Slot=23 drive=0
> > >> odin-sd: dircmd.c:225-0 Do command: label
> > >> odin-sd: dircmd.c:817-0 Try changer device Drive-1
> > >> odin-sd: dircmd.c:842-0 Device AutochangerOdin drive wrong: want=0
> got=0
> > >> skipping
> > >>
> > >>
> > >>
> > >> Steve Garcia
> > >> Ignorance killed the cat, curiosity was framed.
> > >>
> > >> ---- "Ana Emília M. Arruda" <emiliaarr...@gmail.com> wrote:
> > >> > Hello Steve,
> > >> >
> > >> > Sorry, I sent an incomplete message.
> > >> >
> > >> > I think we will need to speak the same language here :-)
> > >> >
> > >> > You have your Director running at sleipnir host:
> > >> >
> > >> > root@sleipnir:/etc/bacula# bconsole
> > >> > Connecting to Director sleipnir:9101
> > >> > 1000 OK: 102 sleipnir-dir Version: 7.4.3 (18 June 2016)
> > >> >
> > >> > with the Autochanger configuration on Director:
> > >> >
> > >> > From bacula-dir.conf on sleipnir (where the director is):
> > >> > Storage {
> > >> > Name = Library2
> > >> > # Do not use "localhost" here
> > >> > Address = odin # N.B. Use a fully qualified name
> here
> > >> > SDPort = 9103
> > >> > Password = "*****************"
> > >> > Device = AutochangerOdin
> > >> > Media Type = LTO6
> > >> > Autochanger = yes # enable for autochanger
> device
> > >> > }
> > >> >
> > >> > And you have your remote Storage Daemon installed in a host called
> > >> > odin with the following configuration:
> > >> >
> > >> > From the bacula-sd.conf on odin (where the library is):
> > >> > Autochanger {
> > >> > Name = AutochangerOdin
> > >> > Device = Drive-1
> > >> > Changer Command = "/etc/bacula/scripts/mtx-changer %c %o %S %a
> %d"
> > >> > Changer Device = /dev/autochanger1
> > >> > }
> > >> >
> > >> > Device {
> > >> > Name = Drive-1 #
> > >> > Description = "LT06 inside Dell TL2000 Library"
> > >> > Drive Index = 0
> > >> > Media Type = LT06
> > >> > Archive Device = /dev/nst0
> > >> > AutomaticMount = yes; # when device opened, read it
> > >> > AlwaysOpen = yes;
> > >> > RemovableMedia = yes;
> > >> > RandomAccess = no;
> > >> > AutoChanger = yes
> > >> > SpoolDirectory = "/var/spool/bacula"
> > >> > MaximumSpoolSize = 485G
> > >> > Maximum Network Buffer Size = 65536
> > >> > Offline On Unmount = no
> > >> > Alert Command = "sh -c 'smartctl -H -l error %c'"
> > >> > }
> > >> > This is perfect.
> > >> >
> > >> > You are right, the permission needs to be checked.
> > >> >
> > >> > If you have bacula-sd runnig as bacula user, the bacula user must be
> > >> member
> > >> > of tape group.
> > >> >
> > >> > Also, you can start the bacula-sd daemon in debug mode to get some
> debug
> > >> > output and maybe help in this case. The following command should be
> run
> > >> on
> > >> > odin host:
> > >> >
> > >> > * sudo -u bacula -g tape /opt/ bacula/bin/bacula-sd -d200
> > >> >
> > >> > This will produce debug information on the Storage Daemon host and
> > >> maybe we
> > >> > can have more information about this problem.
> > >> >
> > >> > Best,
> > >> > Ana
> > >> >
> > >> > On Mon, Jul 31, 2017 at 3:58 PM, Steve Garcia <sgar...@bak.rr.com>
> > >> wrote:
> > >> >
> > >> > >
> > >> > >
> > >> > > ---- Darold Lucus <dlu...@emacinc.com> wrote:
> > >> > > > This is an example of my Autochanger listing in the
> bacula-sd.conf,
> > >> this
> > >> > > is
> > >> > > > only a partial list but you would follow that format. My
> > >> autochanger has
> > >> > > 16
> > >> > > > slots and a drive, the drive-1 is the writing drive.
> > >> > > >
> > >> > > > AutoChanger {
> > >> > > > Name = AutoChanger
> > >> > > > Device = Drive-1, Drive-2, Drive-3, Drive-4, Drive-5,
> Drive-6,
> > >> > > Drive-7,
> > >> > > > Drive-8, Drive-9, Drive-10, Drive-11, Drive-12, Drive-13,
> Drive-14,
> > >> > > > Drive-15, Drive-16, Drive-17
> > >> > > > Changer Command = "/etc/bacula/scripts/mtx-changer %c %o %S
> %a
> > >> %d"
> > >> > > > Changer Device = /dev/sg1
> > >> > > > }
> > >> > >
> > >> > > So you're defining each slot as a drive, but only defining the
> actual
> > >> > > drive as a device?
> > >> > >
> > >> > > >
> > >> > > > Device {
> > >> > > > Name = Drive-1 #
> > >> > > > Drive Index = 0
> > >> > > > Media Type = LTO5
> > >> > > > Archive Device = /dev/st0
> > >> > > > AutomaticMount = yes; # when device opened,
> read it
> > >> > > > AlwaysOpen = yes;
> > >> > > > RemovableMedia = yes;
> > >> > > > RandomAccess = no;
> > >> > > > AutoChanger = yes
> > >> > > >
> > >> > > > }
> > >> > > >
> > >> > > > You also don't need this information in your storage section:
> > >> > > >
> > >> > > > Device = AutochangerOdin
> > >> > > > Media Type = LTO6
> > >> > > > Autochanger = yes # enable for autochanger
> > >> device
> > >> > >
> > >> > > Well, I don't have those defined in the Storage resource of the
> > >> > > bacula-sd.conf configuration (which is on the remote machine
> where the
> > >> > > storage daemon lives) but I *do* have it in the Storage resource
> > >> which is
> > >> > > part of the bacula-dir.conf configuration. The director gets
> quite
> > >> cranky
> > >> > > if you leave it out there. :-)
> > >> > >
> > >> > >
> > >> > >
> > >> > >
> > >> > > >
> > >> > > > This is my example:
> > >> > > >
> > >> > > > Storage { # definition of myself
> > >> > > > Name = nas-sd
> > >> > > > SDPort = 9103 # Director's port
> > >> > > > WorkingDirectory = "/var/lib/bacula"
> > >> > > > Pid Directory = "/var/run/bacula"
> > >> > > > Maximum Concurrent Jobs = 20
> > >> > > > SDAddress = IP.ADD.RE.SS
> > >> > > > }
> > >> > > >
> > >> > > >
> > >> > > > Hope this helps.
> > >> > > >
> > >> > > >
> > >> > > >
> > >> > > >
> > >> > > > Sincerely,
> > >> > > >
> > >> > > > Darold Lucus
> > >> > > >
> > >> > > >
> > >> > > > [image: cid:image002.png@01D06336.119F49E0] <
> > >> http://www.emacinc.com/>
> > >> > > >
> > >> > > > =====================
> > >> > > > LAN Administrator
> > >> > > > EMAC, Inc
> > >> > > > 618-529-4525 EXT:370
> > >> > > > www.emacinc.com
> > >> > > > =====================
> > >> > > >
> > >> > > >
> > >> > > >
> > >> > > > This message is confidential. It may also be privileged or
> otherwise
> > >> > > > protected by work product immunity or other legal rules. If you
> have
> > >> > > > received it by mistake, please let us know by e-mail reply and
> > >> delete it
> > >> > > > from your system; you may not copy this message or disclose its
> > >> contents
> > >> > > to
> > >> > > > anyone.
> > >> > > >
> > >> > > > On Thu, Jul 27, 2017 at 4:00 PM, Ana Emília M. Arruda <
> > >> > > > emiliaarr...@gmail.com> wrote:
> > >> > > >
> > >> > > > > Hi Steve,
> > >> > > > >
> > >> > > > > Sorry, my mistake...
> > >> > > > >
> > >> > > > > There is no problem in having a remote Storage Daemon with
> your
> > >> tape
> > >> > > > > library attached. This is a very usual configuration.
> > >> > > > >
> > >> > > > > Before having a try with Bacula, I would recommend you to
> check
> > >> if mtx
> > >> > > and
> > >> > > > > mt are properly working (please use /dev/tape/by-id names when
> > >> running
> > >> > > > > tests).
> > >> > > > >
> > >> > > > > The error messages seems related to the tape drive and not to
> the
> > >> tape
> > >> > > > > library configuration. So I would try "/dev/tape/by-id/scsi-
> > >> > > 35000e11164c42001-nst"
> > >> > > > > for the tape device:
> > >> > > > >
> > >> > > > > Device {
> > >> > > > > Name = Drive-1 #
> > >> > > > > Description = "LT06 inside Dell TL2000 Library"
> > >> > > > > Drive Index = 0
> > >> > > > > Media Type = LT06
> > >> > > > > Archive Device = /dev/tape/by-id/scsi-35000e11164c42001-nst
> > >> > > > > AutomaticMount = yes; # when device opened,
> read
> > >> it
> > >> > > > > AlwaysOpen = yes;
> > >> > > > > RemovableMedia = yes;
> > >> > > > > RandomAccess = no;
> > >> > > > > AutoChanger = yes
> > >> > > > > SpoolDirectory = "/var/spool/bacula"
> > >> > > > > MaximumSpoolSize = 485G
> > >> > > > > Maximum Network Buffer Size = 65536
> > >> > > > > Offline On Unmount = no
> > >> > > > > Alert Command = "sh -c 'smartctl -H -l error %c'"
> > >> > > > > }
> > >> > > > >
> > >> > > > > You should run btape tests before starting backups as well.
> > >> > > > >
> > >> > > > > Best regards,
> > >> > > > >
> > >> > > > > Ana
> > >> > > > >
> > >> > > > >
> > >> > > > > On Wed, Jul 26, 2017 at 3:20 PM, Steve Garcia <
> sgar...@bak.rr.com
> > >> >
> > >> > > wrote:
> > >> > > > >
> > >> > > > >> OK, I've got my tape drive working (thanks Ana!) but I'm
> having
> > >> > > trouble
> > >> > > > >> connecting to the autochanger it's in using the director.
> This
> > >> is the
> > >> > > > >> first time I've tried having a storage daemon on a different
> > >> machine
> > >> > > than
> > >> > > > >> the director. The director is a slightly lower version
> (7.4.3 on
> > >> > > Debian
> > >> > > > >> Jessie using backports) than the storage daemon (7.4.4 on
> > >> stretch)
> > >> > > but I
> > >> > > > >> had understood that those versions were close enough to work.
> > >> > > > >>
> > >> > > > >> So I'm hoping this is another configuration issue.
> > >> > > > >>
> > >> > > > >> Right now what I'm trying to do is label all the tapes in
> the new
> > >> > > library.
> > >> > > > >>
> > >> > > > >> When I try to access the new storage from the director, it is
> > >> able to
> > >> > > get
> > >> > > > >> a listing of all the tapes, but it fails when it tries to
> > >> actually do
> > >> > > the
> > >> > > > >> labeling. I get a "3999 Device not found or could not be
> opened"
> > >> > > error.
> > >> > > > >> These errors show up quickly, there is no delay as it tries
> each
> > >> > > slot, so
> > >> > > > >> it's obviously not getting far enough to try. But it *is*
> > >> obviously
> > >> > > > >> connecting to the remote storage, otherwise it wouldn't be
> able
> > >> to
> > >> > > obtain
> > >> > > > >> the slot list.
> > >> > > > >>
> > >> > > > >> What am I missing?
> > >> > > > >>
> > >> > > > >> root@sleipnir:/etc/bacula# bconsole
> > >> > > > >> Connecting to Director sleipnir:9101
> > >> > > > >> 1000 OK: 102 sleipnir-dir Version: 7.4.3 (18 June 2016)
> > >> > > > >> Enter a period to cancel a command.
> > >> > > > >> *label storage=Library2 barcodes
> > >> > > > >> Automatically selected Catalog: MyCatalog
> > >> > > > >> Using Catalog "MyCatalog"
> > >> > > > >> Connecting to Storage daemon Library2 at odin:9103 ...
> > >> > > > >> 3306 Issuing autochanger "slots" command.
> > >> > > > >> Device "AutochangerOdin" has 24 slots.
> > >> > > > >> Connecting to Storage daemon Library2 at odin:9103 ...
> > >> > > > >> 3306 Issuing autochanger "list" command.
> > >> > > > >> The following Volumes will be labeled:
> > >> > > > >> Slot Volume
> > >> > > > >> ==============
> > >> > > > >> 1 000015L6
> > >> > > > >> 2 000018L6
> > >> > > > >> 3 000021L6
> > >> > > > >> 4 CLNU00L1
> > >> > > > >> 5 000014L6
> > >> > > > >> 6 000017L6
> > >> > > > >> 7 000020L6
> > >> > > > >> 8 CLN005L3
> > >> > > > >> 9 000013L6
> > >> > > > >> 10 000016L6
> > >> > > > >> 11 000019L6
> > >> > > > >> 12 000012L6
> > >> > > > >> 13 000009L6
> > >> > > > >> 14 000006L6
> > >> > > > >> 15 000003L6
> > >> > > > >> 16 000011L6
> > >> > > > >> 17 000008L6
> > >> > > > >> 18 000005L6
> > >> > > > >> 19 000002L6
> > >> > > > >> 20 000010L6
> > >> > > > >> 21 000007L6
> > >> > > > >> 22 000004L6
> > >> > > > >> 23 000001L6
> > >> > > > >> Do you want to label these Volumes? (yes|no): yes
> > >> > > > >> Defined Pools:
> > >> > > > >> 1: Default
> > >> > > > >> 2: OdinPool
> > >> > > > >> Select the Pool (1-2): 2
> > >> > > > >> Connecting to Storage daemon Library2 at odin:9103 ...
> > >> > > > >> Sending label command for Volume "000015L6" Slot 1 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000015L6.
> > >> > > > >> Sending label command for Volume "000018L6" Slot 2 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000018L6.
> > >> > > > >> Sending label command for Volume "000021L6" Slot 3 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000021L6.
> > >> > > > >> Media record for Slot 4 Volume "CLNU00L1" already exists.
> > >> > > > >> Sending label command for Volume "000014L6" Slot 5 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000014L6.
> > >> > > > >> Sending label command for Volume "000017L6" Slot 6 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000017L6.
> > >> > > > >> Sending label command for Volume "000020L6" Slot 7 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000020L6.
> > >> > > > >> Media record for Slot 8 Volume "CLN005L3" already exists.
> > >> > > > >> Sending label command for Volume "000013L6" Slot 9 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000013L6.
> > >> > > > >> Sending label command for Volume "000016L6" Slot 10 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000016L6.
> > >> > > > >> Sending label command for Volume "000019L6" Slot 11 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000019L6.
> > >> > > > >> Sending label command for Volume "000012L6" Slot 12 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000012L6.
> > >> > > > >> Sending label command for Volume "000009L6" Slot 13 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000009L6.
> > >> > > > >> Sending label command for Volume "000006L6" Slot 14 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000006L6.
> > >> > > > >> Sending label command for Volume "000003L6" Slot 15 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000003L6.
> > >> > > > >> Sending label command for Volume "000011L6" Slot 16 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000011L6.
> > >> > > > >> Sending label command for Volume "000008L6" Slot 17 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000008L6.
> > >> > > > >> Sending label command for Volume "000005L6" Slot 18 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000005L6.
> > >> > > > >> Sending label command for Volume "000002L6" Slot 19 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000002L6.
> > >> > > > >> Sending label command for Volume "000010L6" Slot 20 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000010L6.
> > >> > > > >> Sending label command for Volume "000007L6" Slot 21 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000007L6.
> > >> > > > >> Sending label command for Volume "000004L6" Slot 22 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000004L6.
> > >> > > > >> Sending label command for Volume "000001L6" Slot 23 ...
> > >> > > > >> 3999 Device "AutochangerOdin" not found or could not be
> opened.
> > >> > > > >> Label command failed for Volume 000001L6.
> > >> > > > >> You have messages.
> > >> > > > >> *
> > >> > > > >>
> > >> > > > >> From the bacula-sd.conf on odin (where the library is):
> > >> > > > >> Autochanger {
> > >> > > > >> Name = AutochangerOdin
> > >> > > > >> Device = Drive-1
> > >> > > > >> Changer Command = "/etc/bacula/scripts/mtx-changer %c %o
> %S
> > >> %a %d"
> > >> > > > >> Changer Device = /dev/autochanger1
> > >> > > > >> }
> > >> > > > >>
> > >> > > > >> Device {
> > >> > > > >> Name = Drive-1 #
> > >> > > > >> Description = "LT06 inside Dell TL2000 Library"
> > >> > > > >> Drive Index = 0
> > >> > > > >> Media Type = LT06
> > >> > > > >> Archive Device = /dev/nst0
> > >> > > > >> AutomaticMount = yes; # when device opened,
> read
> > >> it
> > >> > > > >> AlwaysOpen = yes;
> > >> > > > >> RemovableMedia = yes;
> > >> > > > >> RandomAccess = no;
> > >> > > > >> AutoChanger = yes
> > >> > > > >> SpoolDirectory = "/var/spool/bacula"
> > >> > > > >> MaximumSpoolSize = 485G
> > >> > > > >> Maximum Network Buffer Size = 65536
> > >> > > > >> Offline On Unmount = no
> > >> > > > >> Alert Command = "sh -c 'smartctl -H -l error %c'"
> > >> > > > >> }
> > >> > > > >>
> > >> > > > >> From bacula-dir.conf on sleipnir (where the director is):
> > >> > > > >> Storage {
> > >> > > > >> Name = Library2
> > >> > > > >> # Do not use "localhost" here
> > >> > > > >> Address = odin # N.B. Use a fully qualified
> > >> name here
> > >> > > > >> SDPort = 9103
> > >> > > > >> Password = "*****************"
> > >> > > > >> Device = AutochangerOdin
> > >> > > > >> Media Type = LTO6
> > >> > > > >> Autochanger = yes # enable for
> autochanger
> > >> device
> > >> > > > >> }
> > >> > > > >>
> > >> > > > >> From the /dev directory on odin:
> > >> > > > >> lrwxrwxrwx 1 root root 3 Jun 5 17:42 /dev/autochanger1
> ->
> > >> sg3
> > >> > > > >> crw-rw---- 1 root tape 21, 3 Jun 1 15:01 /dev/sg3
> > >> > > > >>
> > >> > > > >>
> > >> > > > >>
> > >> > > > >> --
> > >> > > > >> Steve Garcia
> > >> > > > >> Ignorance killed the cat, curiosity was framed.
> > >> > > > >>
> > >> > > > >> ------------------------------------------------------------
> > >> > > > >> ------------------
> > >> > > > >> Check out the vibrant tech community on one of the world's
> most
> > >> > > > >> engaging tech sites, Slashdot.org! http://sdm.link/slashdot
> > >> > > > >> _______________________________________________
> > >> > > > >> Bacula-users mailing list
> > >> > > > >> Bacula-users@lists.sourceforge.net
> > >> > > > >> https://lists.sourceforge.net/lists/listinfo/bacula-users
> > >> > > > >>
> > >> > > > >
> > >> > > > >
> > >> > > > > ------------------------------------------------------------
> > >> > > > > ------------------
> > >> > > > > Check out the vibrant tech community on one of the world's
> most
> > >> > > > > engaging tech sites, Slashdot.org! http://sdm.link/slashdot
> > >> > > > > _______________________________________________
> > >> > > > > Bacula-users mailing list
> > >> > > > > Bacula-users@lists.sourceforge.net
> > >> > > > > https://lists.sourceforge.net/lists/listinfo/bacula-users
> > >> > > > >
> > >> > > > >
> > >> > >
> > >> > >
> > >>
> > >>
> > >
>
>
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
