Hi at all,
yesterday my TAPE reader (an HP LTO3 Ultrium) stop
working, without a reason. I'm using Bacula 5.0.0 on
Centos 5.4 (32bit).
I've tried to change the Tape (T've supposed was damaged)
without better results, also using a new tape.
Then, I stopped everything and I've tried to run btape test:
$ btape -c bacula-sd.conf /dev/nst0
Tape block granularity is 1024 bytes.
btape: butil.c:285 Using device: "/dev/nst0" for writing.
btape: btape.c:476 open device "LTO-3" (/dev/nst0): OK
*test
=== Write, rewind, and re-read test ===
I'm going to write 10000 records and an EOF
then write 10000 records and an EOF, then rewind,
and re-read the data to verify that it is correct.
This is an *essential* feature ...
btape: btape.c:1148 Wrote 10000 blocks of 64412 bytes.
btape: btape.c:604 Bad status from weof. ERR=dev.c:1740
ioctl MTWEOF error on "LTO-3" (/dev/nst0).
ERR=Input/output error.
01-Apr 11:21 btape JobId 0: Error: block.c:573 Write error
at 0:10000 on device "LTO-3" (/dev/nst0). ERR=Input/output
error.
01-Apr 11:21 btape JobId 0: Error: Error writing final EOF
to tape. This Volume may not be readable.
dev.c:1740 ioctl MTWEOF error on "LTO-3" (/dev/nst0).
ERR=Input/output error.
btape: btape.c:1160 Error writing block to device.
Searching with google, I've founded a tip about SD
configuration: add a TWO OEF = yes in the LTO section, but
neither this one works. Following what I can see from
dmesg:
mptscsih: ioc0: attempting task abort! (sc=f5d3f840)
st 0:0:0:0:
command: Write Filemarks: 10 00 00 00 01 00
mptbase: ioc0: Initiating recovery
mptscsih: ioc0: Issue of TaskMgmt failed!
mptscsih: ioc0: task abort: FAILED (sc=f5d3f840)
mptscsih: ioc0: attempting target reset! (sc=f5d3f840)
st 0:0:0:0:
command: Write Filemarks: 10 00 00 00 01 00
mptscsih: ioc0: target reset: SUCCESS (sc=f5d3f840)
st 0:0:0:0: timing out command, waited 900s
st0: Error 6000002 (sugg. bt 0x0, driver bt 0x6, host bt
0x0).
target0:0:0: Beginning Domain Validation
target0:0:0: Ending Domain Validation
target0:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI
PCOMP (6.25 ns, offset 64)
mptscsih: ioc0: attempting task abort! (sc=f5ee0200)
st 0:0:0:0:
command: Write Filemarks: 10 00 00 00 01 00
mptbase: ioc0: Initiating recovery
mptscsih: ioc0: Issue of TaskMgmt failed!
mptscsih: ioc0: task abort: FAILED (sc=f5ee0200)
mptscsih: ioc0: attempting target reset! (sc=f5ee0200)
st 0:0:0:0:
command: Write Filemarks: 10 00 00 00 01 00
mptscsih: ioc0: target reset: SUCCESS (sc=f5ee0200)
st 0:0:0:0: timing out command, waited 900s
st0: Error 6000002 (sugg. bt 0x0, driver bt 0x6, host bt
0x0).
target0:0:0: Beginning Domain Validation
target0:0:0: Ending Domain Validation
target0:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI
PCOMP (6.25 ns, offset 64)
Any suggestions?
Regards,
Simone
------------------------------------------------------------------------------
Download Intel® Parallel Studio Eval
Try the new software tools for yourself. Speed compiling, find bugs
proactively, and fine-tune applications for parallel performance.
See why Intel Parallel Studio got high marks during beta.
http://p.sf.net/sfu/intel-sw-dev
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
