On Mon, Jan 14, 2008 at 04:12:22PM -0500, Robin Blanchard wrote: > I've been around the block with LSI and with adaptec: tried an LSI > SYMC101, an adaptec 2940U2W and a 39160. I've removed the > library/exchange from the equation, using only the LTO-3 drive (and have > actually swapped that drive out for another as well), swapped SCSI > cables, and terminators, and still am getting scsi errors. Anyone got > any tips/ideas here ? > > target2:0:1: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) > Vendor: IBM Model: ULTRIUM-TD3 Rev: 73P5 > Type: Sequential-Access ANSI SCSI revision: 03 > target2:0:1: Beginning Domain Validation > target2:0:1: asynchronous > target2:0:1: wide asynchronous > target2:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62) > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > target2:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62) > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > target2:0:1: Domain Validation detected failure, dropping back > target2:0:1: control msgout: c. > sym0: TARGET 1 has been reset. > target2:0:1: Domain Validation detected failure, dropping back > target2:0:1: FAST-40 WIDE SCSI 66.0 MB/s DT (30.3 ns, offset 62) > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > target2:0:1: FAST-40 WIDE SCSI 66.0 MB/s DT (30.3 ns, offset 62) > sym0: SCSI parity error detected: SCR1=1 DBC=15000002 SBCL=ae > sym0: SCSI parity error detected: SCR1=1 DBC=15000000 SBCL=2d > sym0:1: ERROR (0:8) (d-ae-5) (3e/38/8c) @ (scripta 98:870b0000). > sym0: script cmd = 800a0000 > sym0: regdump: da 10 c0 38 47 3e 01 0a 03 0d 00 ae 80 00 0e 00 00 1c 6f > 08 2a 00 00 00. > sym0: SCSI BUS reset detected. > sym0: SCSI BUS has been reset. > target2:0:1: Domain Validation detected failure, dropping back > target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) > target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) > target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) > target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) > target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s DT (50 ns, offset 62) > target2:0:1: Domain Validation skipping write tests > target2:0:1: Ending Domain Validation > scsi 2:0:1:0: Attached scsi generic sg2 type 1 > ACPI: PCI Interrupt 0000:05:02.1[B] -> GSI 101 (level, low) -> IRQ 22 > sym1: <1010-33> rev 0x1 at pci 0000:05:02.1 irq 22 > sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking > sym1: open drain IRQ line driver, using on-chip SRAM > sym1: using LOAD/STORE-based firmware. > sym1: handling phase mismatch from SCRIPTS. > sym1: SCSI BUS has been reset. > scsi3 : sym-2.2.3
what i would try, being the brute force kinda guy i am, try drive/adapter/cabling on a different machine, maybe different os. different slots on the existing machine. what os is this on again? -- michael ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
