On Mon, Jan 14, 2008 at 10:34:45PM +0000, Nick - wrote:
> I'm having difficulty posting so I apologize if this is a repost.
>
>
>
>
> Hello Everyone,
>
> I’m new to using Bacula and am having a little trouble setting up
> the configurations.
>
>
> When I run cat /proc/scsi/scsi I get the following back
>
> Attached devices:
> Host: scsi0 Channel: 00 Id: 00 Lun: 00
> Vendor: DELL Model: PV-132T Rev: 308D
> Type: Medium Changer ANSI SCSI revision: 02
> Host: scsi0 Channel: 00 Id: 01 Lun: 00
> Vendor: IBM Model: ULTRIUM-TD2 Rev: 53Y3
> Type: Sequential-Access ANSI SCSI revision: 03
> Host: scsi0 Channel: 01 Id: 02 Lun: 00
> Vendor: IBM Model: ULTRIUM-TD2 Rev: 37RH
> Type: Sequential-Access ANSI SCSI revision: 03
> Host: scsi1 Channel: 00 Id: 08 Lun: 00
> Vendor: DP Model: BACKPLANE Rev: 1.05
> Type: Enclosure ANSI SCSI revision: 05
> Host: scsi1 Channel: 02 Id: 00 Lun: 00
> Vendor: DELL Model: PERC 5/i Rev: 1.03
> Type: Direct-Access ANSI SCSI revision: 05
>
> Next I run mtx –f /dev/sg0 status
>
> Storage Changer /dev/sg0:2 Drives, 23 Slots ( 1 Import/Export )
> Data Transfer Element 0:Empty
> Data Transfer Element 1:Empty
> Storage Element 1:Full :VolumeTag=000013
> Storage Element 2:Full :VolumeTag=000019
> Storage Element 3:Full :VolumeTag=000020
> Storage Element 4:Full :VolumeTag=000021
> Storage Element 5:Full :VolumeTag=000017
> Storage Element 6:Full :VolumeTag=000018
> Storage Element 7:Full :VolumeTag=000022
> Storage Element 8:Full :VolumeTag=000001
> Storage Element 9:Full :VolumeTag=000008
> Storage Element 10:Full :VolumeTag=000004
> Storage Element 11:Full :VolumeTag=000007
> Storage Element 12:Full :VolumeTag=000011
> Storage Element 13:Full :VolumeTag=000009
> Storage Element 14:Full :VolumeTag=000010
> Storage Element 15:Full :VolumeTag=000016
> Storage Element 16:Full :VolumeTag=000002
> Storage Element 17:Empty:VolumeTag=
> Storage Element 18:Full :VolumeTag=000014
> Storage Element 19:Full :VolumeTag=000015
> Storage Element 20:Full :VolumeTag=000003
> Storage Element 21:Full :VolumeTag=000005
> Storage Element 22:Full :VolumeTag=000006
> Storage Element 23 IMPORT/EXPORT:Full :VolumeTag=000012
>
> /mtx –f /dev/sg0 inquiry shows:
>
> Product Type: Medium Changer
> Vendor ID: 'DELL '
> Product ID: 'PV-132T '
> Revision: '308D'
> Attached Changer API: No
>
> /mtx –f /dev/sg1 inquiry shows:
> Product Type: Tape Drive
> Vendor ID: 'IBM '
> Product ID: 'ULTRIUM-TD2 '
> Revision: '53Y3'
> Attached Changer API: No
>
> /mtx –f /dev/sg2 inquiry shows:
> Product Type: Tape Drive
> Vendor ID: 'IBM '
> Product ID: 'ULTRIUM-TD2 '
> Revision: '37RH'
> Attached Changer API: No
>
> /mt –f /dev/nst0 status shows:
> SCSI 2 tape drive:
> File number=-1, block number=-1, partition=0.
> Tape block size 0 bytes. Density code 0x0 (default).
> Soft error count since last status=0
> General status bits on (50000):
> DR_OPEN IM_REP_EN
>
>
>
> In bacula-sd.conf I have the following setup:
>
> Autochanger {
> Name = Autochanger
> Device = DellPowerVault132T
> Changer Command = "/etc/bacula/mtx-changer %c %o %S %a %d"
> Changer Device = /dev/sg0
> }
>
> Device {
> Name = DellPowerVault132T
> LabelMedia = yes
> Drive Index = 0
> Media Type = LTO-3
> Archive Device = /dev/nst0
> AutomaticMount = yes;
> AlwaysOpen = yes;
> RemovableMedia = yes;
> RandomAccess = no;
> AutoChanger = yes
> Hardware End of Medium = No
> BSF at EOM = yes
> # Enable the Alert command only if you have the mtx package loaded
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
> TWO EOF = yes
> }
>
>
> Also in the bacula-dir.conf I have the following setup:
> Storage {
> Name = File
> # Do not use "localhost" here
> Address = <<server_name>> # N.B. Use a fully qualified name
> here
> SDPort = 9103
> Password = "<xxx>"
> Device = DellPowerVault132T
> Media Type = LTO-3
> }
>
>
> Does everything look correctly setup?
>
> When I try to mounting the storage using the Webmin Bacula console I get the
> following error:
>
> Mounting volume on storage device File .. Automatically selected Catalog:
> MyCatalogUsing Catalog "MyCatalog"3301 Issuing autochanger "loaded? drive 0"
> command.3302 Autochanger "loaded? drive 0", result: nothing loaded.3901 open
> device failed: ERR=dev.c:433 Unable to open device "DellPowerVault132T"
> (/dev/nst0): ERR=No medium found
>
looks like it just cannot load a tape. did you work thru the btape test parts
of the bacula manual? might
try from the console:
update slots
mount
-- michael
-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
