Robin Blanchard wrote: > Ok. Thanks for the tip. I was pointing at the wrong changer. > > # mtx -f /dev/sg2 status > Storage Changer /dev/sg2:1 Drives, 20 Slots ( 0 Import/Export ) > Data Transfer Element 0:Full (Storage Element 2 Loaded):VolumeTag = > B00039L3 > Storage Element 1:Full :VolumeTag=B00023L3 > Storage Element 2:Empty > Storage Element 3:Full :VolumeTag=B00029L3 > Storage Element 4:Full :VolumeTag=B00025L3 > Storage Element 5:Full :VolumeTag=B00028L3 > Storage Element 6:Full :VolumeTag=B00022L3 > Storage Element 7:Full :VolumeTag=B00026L3 > Storage Element 8:Full :VolumeTag=B00031L3 > Storage Element 9:Full :VolumeTag=B00030L3 > Storage Element 10:Full :VolumeTag=B00037L3 > > Storage Element 11:Full :VolumeTag=B00034L3 > > Storage Element 12:Full :VolumeTag=B00035L3 > > Storage Element 13:Full :VolumeTag=B00036L3 > > Storage Element 14:Full :VolumeTag=B00038L3 > > Storage Element 15:Full :VolumeTag=B00032L3 > > Storage Element 16:Full :VolumeTag=B00024L3 > > Storage Element 17:Full :VolumeTag=B00021L3 > > Storage Element 18:Full :VolumeTag=B00020L3 > > Storage Element 19:Full :VolumeTag=B00027L3 > > Storage Element 20:Full :VolumeTag=B00033L3 > > > > # mt -f /dev/nst0 status > SCSI 2 tape drive: > File number=-1, block number=-1, partition=0. > Tape block size 0 bytes. Density code 0x0 (default). > Soft error count since last status=0 > General status bits on (10000): > IM_REP_EN > > # /usr/local/bacula-2.2.6/sbin/btape -c > /usr/local/bacula-2.2.6/etc/bacula-sd.conf /dev/nst0 > Tape block granularity is 1024 bytes. > btape: butil.c:285 Using device: "/dev/nst0" for writing. > 17-Dec 14:06 btape JobId 0: 3301 Issuing autochanger "loaded? drive 0" > command. > 17-Dec 14:06 btape JobId 0: 3302 Autochanger "loaded? drive 0", result > is Slot 2. > 17-Dec 14:06 btape: Fatal Error at device.c:296 because: > dev open failed: dev.c:433 Unable to open device "Drive-1" (/dev/nst0): > ERR=Input/output error > > 17-Dec 14:06 btape JobId 0: Fatal error: butil.c:194 Cannot open > "Drive-1" (/dev/nst0)
[a lot of old stuff snipped] I think you are now asking for help with the above messages, but you haven't explicitly asked. When running btape, be sure bacula-sd is not running. That is your firstcheck. ------------------------------------------------------------------------- SF.Net email is sponsored by: Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
