Hello, On 5/2/2007 6:01 PM, Mike Seda wrote: > Hi All, > Basically, the error that I received during a bcopy from disk to tape > was the following: > > 01-May 22:48 bcopy: Volume "MSR133L3" previously written, moving to end > of data. > 01-May 22:48 bcopy: bcopy Error: I cannot write on Volume "MSR133L3" > because: > The number of files mismatch! Volume=4 Catalog=0 > 01-May 22:48 bcopy: Marking Volume "MSR133L3" in Error in Catalog. > > Updating the number of volume files in the catalog does not make this > error go away. Does anyone know how I can proceed? I would like to > continue appending to this tape since it has around 500 GB free.
From your previous mail I conclude that data on this tape is invalid because the job writing to it never finished. If that's the case, jus rewind the tape, write two eofs to it (effectively making it unusable for Bacula, so think twice if that's what you want!) and re-label it using btape. On the other hand, setting the number of files to 4 in the catalog should work... at least, afterwards you should not get get an error stating "The number of files mismatch! Volume=4 Catalog=0". Arno > Thx, > Mike > > > Mike Seda wrote: >> Hi All, >> I just have one more question... I executed the following command, but >> (stupidly) hit <CTL><C> shortly thereafter: >> bcopy -c /etc/bacula/bacula-sd.conf -i FILE0002 -o MSR133L3 -v -w >> /var/bacula/spool VG1-LV0 Drive-1 >> >> Now, when I try to execute the aforementioned command again, I get the >> following error: >> [EMAIL PROTECTED] spool]# bcopy -c /etc/bacula/bacula-sd.conf -i FILE0002 >> -o MSR133L3 -v -w /var/bacula/spool VG1-LV0 Drive-1 >> bcopy: butil.c:283 Using device: "VG1-LV0" for reading. >> 01-May 22:48 bcopy: Ready to read from volume "FILE0002" on device >> "VG1-LV0" (/var/bacula/spool). >> bcopy: butil.c:286 Using device: "Drive-1" for writing. >> 01-May 22:48 bcopy: 3301 Issuing autochanger "loaded? drive 0" command. >> 01-May 22:48 bcopy: 3302 Autochanger "loaded? drive 0", result is Slot 30. >> 01-May 22:48 bcopy: 3301 Issuing autochanger "loaded? drive 0" command. >> 01-May 22:48 bcopy: 3302 Autochanger "loaded? drive 0", result is Slot 30. >> 01-May 22:48 bcopy: Invalid slot=0 defined, cannot autoload Volume. >> 01-May 22:48 bcopy: Volume "MSR133L3" previously written, moving to end >> of data. >> 01-May 22:48 bcopy: bcopy Error: I cannot write on Volume "MSR133L3" >> because: >> The number of files mismatch! Volume=4 Catalog=0 >> 01-May 22:48 bcopy: Marking Volume "MSR133L3" in Error in Catalog. >> 01-May 22:49 bcopy: Invalid slot=0 defined, cannot autoload Volume. >> Mount Volume "" on device "Drive-1" (/dev/nst0) and press return when ready: >> >> Any thoughts? >> >> >> Martin Simmons wrote: >> >>>>>>>> On Mon, 30 Apr 2007 17:54:48 -0400, Mike Seda said: >>>>>>>> >>>>>>>> >>>> Hi All, >>>> I successfully bcopied a tape to disk. Then, during a subsequent bcopy >>>> from disk to tape, I got the following output: >>>> >>>> [EMAIL PROTECTED] ~]# bcopy -c /etc/bacula/bacula-sd.conf -i FILE0002 -o >>>> MSR131L3 -v -w /var/bacula/spool VG1-LV0 Drive-1 >>>> bcopy: butil.c:283 Using device: "VG1-LV0" for reading. >>>> 30-Apr 13:36 bcopy: Ready to read from volume "FILE0002" on device >>>> "VG1-LV0" (/var/bacula/spool). >>>> bcopy: butil.c:286 Using device: "Drive-1" for writing. >>>> 30-Apr 13:36 bcopy: 3301 Issuing autochanger "loaded? drive 0" command. >>>> 30-Apr 13:36 bcopy: 3302 Autochanger "loaded? drive 0", result is Slot 28. >>>> 30-Apr 13:36 bcopy: 3301 Issuing autochanger "loaded? drive 0" command. >>>> 30-Apr 13:36 bcopy: 3302 Autochanger "loaded? drive 0", result is Slot 28. >>>> 30-Apr 13:36 bcopy: Invalid slot=0 defined, cannot autoload Volume. >>>> 30-Apr 13:36 bcopy: Wrote label to prelabeled Volume "MSR131L3" on >>>> device "Drive-1" (/dev/nst0) >>>> bcopy: bcopy.c:242 Volume label not copied. >>>> 30-Apr 16:26 bcopy: End of Volume "" at 523:8456 on device "Drive-1" >>>> (/dev/nst0). Write of 64512 bytes got -1. >>>> >>>> >>> This message usually means that the tape is full. >>> >>> >>> >>> >>>> 30-Apr 16:26 bcopy: Re-read of last block succeeded. >>>> >>>> >>> This is good. It means that Bacula is able to read the block before the one >>> that filled the tape. >>> >>> >>> >>> >>>> 30-Apr 16:26 bcopy: End of medium on Volume "" Bytes=523,512,105,984 >>>> Blocks=8,114,956 at 30-Apr-2007 16:26. >>>> 30-Apr 16:26 bcopy: Invalid slot=0 defined, cannot autoload Volume. >>>> Mount Volume "" on device "Drive-1" (/dev/nst0) and press return when >>>> ready: >>>> >>>> What does this mean? I am inclined to thing that bcopy is done. My >>>> paranoid self thinks that I forgot to rewind tape volume "MSR131L3", >>>> which caused this error. Please advise what to do next. >>>> >>>> >>> I would expect Bacula to rewind the tape before copying to it. Could the >>> tape >>> be full? Did the tape contain something already when you started copying to >>> it? >>> >>> Beware also that tapes are not all exactly the same length, so Bacula can't >>> guarantee to copy a full tape to another one. >>> >>> __Martin >>> >>> ------------------------------------------------------------------------- >>> This SF.net email is sponsored by DB2 Express >>> Download DB2 Express C - the FREE version of DB2 express and take >>> control of your XML. No limits. Just data. Click to get it now. >>> http://sourceforge.net/powerbar/db2/ >>> _______________________________________________ >>> Bacula-users mailing list >>> Bacula-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/bacula-users >>> >>> >> >> ------------------------------------------------------------------------- >> This SF.net email is sponsored by DB2 Express >> Download DB2 Express C - the FREE version of DB2 express and take >> control of your XML. No limits. Just data. Click to get it now. >> http://sourceforge.net/powerbar/db2/ >> _______________________________________________ >> Bacula-users mailing list >> Bacula-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/bacula-users >> > > > ------------------------------------------------------------------------- > This SF.net email is sponsored by DB2 Express > Download DB2 Express C - the FREE version of DB2 express and take > control of your XML. No limits. Just data. Click to get it now. > http://sourceforge.net/powerbar/db2/ > _______________________________________________ > Bacula-users mailing list > Bacula-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/bacula-users -- IT-Service Lehmann [EMAIL PROTECTED] Arno Lehmann http://www.its-lehmann.de ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
