I am attempting to restore over 160gb of data that was backed up while some users were still logged in. As a result, some files have size errors.
I do not care if the the bad files are not restored but cannot go through one at a time to add to the exclude list. Is there a way to tell bacula to ignore these errors or is there a better way around this? I believe the first read errors are from the drive not being ready from not long enough of a wait to mount, it goes on the 2nd attempt. 01-Apr 19:35 adam-dir: Begin pruning Jobs. 01-Apr 19:35 adam-dir: No Jobs found to prune. 01-Apr 19:35 adam-dir: Begin pruning Files. 01-Apr 19:35 adam-dir: No Files found to prune. 01-Apr 19:35 adam-dir: End auto prune. 01-Apr 20:02 adam-dir: Start Restore Job RestoreFiles. 2007-04-01_20.02.25 01-Apr 20:02 adam-sd: 3307 Issuing autochanger "unload slot 4, drive 0" command. 01-Apr 20:03 adam-sd: 3304 Issuing autochanger "load slot 8, drive 0" command. 01-Apr 20:04 adam-sd: 3305 Autochanger "load slot 8, drive 0", status is OK. 01-Apr 20:04 adam-sd: 3301 Issuing autochanger "loaded? drive 0" command. 01-Apr 20:04 adam-sd: 3302 Autochanger "loaded? drive 0", result is Slot 8. 01-Apr 20:04 adam-sd: Ready to read from volume "EHL897" on device "DLT0" (/dev/rmt/0n). 01-Apr 20:04 adam-sd: Forward spacing Volume "EHL897" to file:block 28:0. 01-Apr 20:07 adam-sd: End of file 29 on device "DLT0" (/dev/rmt/0n), Volume "EHL897" 01-Apr 20:07 adam-sd: RestoreFiles.2007-04-01_20.02.25 Error: block.c: 994 Read error on fd=4 at file:blk 29:0 on device "DLT0" (/dev/rmt/ 0n). ERR=I/O error. 01-Apr 20:07 adam-sd: End of Volume at file 29 on device "DLT0" (/dev/ rmt/0n), Volume "EHL897" 01-Apr 20:07 adam-sd: 3301 Issuing autochanger "loaded? drive 0" command. 01-Apr 20:07 adam-sd: 3302 Autochanger "loaded? drive 0", result is Slot 8. 01-Apr 20:07 adam-sd: 3307 Issuing autochanger "unload slot 8, drive 0" command. 01-Apr 20:10 adam-sd: 3304 Issuing autochanger "load slot 4, drive 0" command. 01-Apr 20:11 adam-sd: 3305 Autochanger "load slot 4, drive 0", status is OK. 01-Apr 20:11 adam-sd: 3301 Issuing autochanger "loaded? drive 0" command. 01-Apr 20:11 adam-sd: 3302 Autochanger "loaded? drive 0", result is Slot 4. 01-Apr 20:11 adam-sd: RestoreFiles.2007-04-01_20.02.25 Warning: acquire.c:200 Read open device "DLT0" (/dev/rmt/0n) Volume "EHL892" failed: ERR=dev.c:424 Unable to open device "DLT0" (/dev/rmt/0n): ERR=I/O error 01-Apr 20:11 adam-sd: 3301 Issuing autochanger "loaded? drive 0" command. 01-Apr 20:11 adam-sd: 3302 Autochanger "loaded? drive 0", result is Slot 4. 01-Apr 20:11 adam-sd: Ready to read from volume "EHL892" on device "DLT0" (/dev/rmt/0n). 01-Apr 20:11 adam-sd: Forward spacing Volume "EHL892" to file:block 5:0. 01-Apr 20:13 adam-fd: RestoreFiles.2007-04-01_20.02.25 Error: attribs.c:409 File size of restored file /export/storedge0/restored/ export/storedge0/engineering/BACKUP/DRAW Backup/TMC/01-003/TABLE MOUNTAIN/Casino/E-202.dwg not correct. Original 538714, restored 327680. 01-Apr 20:13 adam-sd: End of file 6 on device "DLT0" (/dev/rmt/0n), Volume "EHL892" 01-Apr 20:13 adam-sd: RestoreFiles.2007-04-01_20.02.25 Error: block.c: 994 Read error on fd=4 at file:blk 6:0 on device "DLT0" (/dev/rmt/ 0n). ERR=I/O error. 01-Apr 20:13 adam-sd: End of Volume at file 6 on device "DLT0" (/dev/ rmt/0n), Volume "EHL892" 01-Apr 20:13 adam-sd: End of all volumes. 01-Apr 20:13 adam-dir: RestoreFiles.2007-04-01_20.02.25 Error: Bacula 2.0.2 (28Jan07): 01-Apr-2007 20:13:02 JobId: 1378 Job: RestoreFiles.2007-04-01_20.02.25 Client: adam-fd Start time: 01-Apr-2007 20:02:27 End time: 01-Apr-2007 20:13:02 Files Expected: 22,799 Files Restored: 961 Bytes Restored: 744,160,622 Rate: 1171.9 KB/s FD Errors: 1 FD termination status: Error SD termination status: OK Termination: *** Restore Error *** 01-Apr 20:13 adam-dir: Begin pruning Jobs. 01-Apr 20:13 adam-dir: No Jobs found to prune. 01-Apr 20:13 adam-dir: Begin pruning Files. 01-Apr 20:13 adam-dir: No Files found to prune. 01-Apr 20:13 adam-dir: End auto prune. ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
