Dear All While backing up a laptop with a large amount of data the laptop went into suspend/standby mode while the 10GB of data was being written to tape (approx through put to tape is about 10 GB /hour). See below.
I have fixed the laptop's power options it now never goes into stand by or hibernate than the disc spin down is 2 hours. My other option was to reduce the spool data size. The problem is the there is a mismatch after the disconnection. In the Manual section under Tips and Suggestions it indicates this only occurs when the Director or Storage daemon crashes - maybe the File Daemon should be added. I manually used this method to get the Volume out of its error state. See Below. I understand the reason for Bacula to be conservative with regard to volume versus catalog information but I wonder if there could be an option to automatically correct the mismatch and issue a Warning email / message instead of the OK message/email so the sysadmin can then check the Volume is ok by restoring a file from the job. I cannot be the only person using Bacula to backup clients over the network - what if a switch or router fails this would cause a similar problem. This software beats the pants off any commercial software I have used / tested. Thanks Stephen Carr ------ FD network error 14-Sep 11:15 elizabeth-sd: 3304 Issuing autochanger "load slot 1, drive 0" command. 14-Sep 11:16 elizabeth-sd: 3305 Autochanger "load slot 1, drive 0", status is OK. 14-Sep 11:16 elizabeth-sd: 3301 Issuing autochanger "loaded drive 0" command. 14-Sep 11:16 elizabeth-sd: 3302 Autochanger "loaded drive 0", result is Slot 1. 14-Sep 11:16 elizabeth-sd: Wrote label to prelabeled Volume "Full-B1" on device "DDS" (/dev/nst0) 14-Sep 11:16 elizabeth-sd: Spooling data ... 14-Sep 11:37 elizabeth-sd: User specified spool size reached. 14-Sep 11:37 elizabeth-sd: Writing spooled data to Volume. Despooling 10,000,058,498 bytes ... 14-Sep 12:35 elizabeth-sd: Spooling data again ... 14-Sep 13:25 elizabeth-dir: civengb183.2006-09-14_11.10.04 Fatal error: Network error with FD during Backup: ERR=Connection timed out 14-Sep 13:25 elizabeth-dir: civengb183.2006-09-14_11.10.04 Fatal error: No Job status returned from FD. 14-Sep 13:25 elizabeth-dir: civengb183.2006-09-14_11.10.04 Error: Bacula 1.38.11 (28Jun06): 14-Sep-2006 13:25:55 ---- Mismatch 14-Sep 20:15 elizabeth-dir: Start Backup JobId 452, Job=BackupCatalog.2006-09-14_19.40.00 14-Sep 20:15 elizabeth-sd: 3301 Issuing autochanger "loaded drive 0" command. 14-Sep 20:15 elizabeth-sd: 3302 Autochanger "loaded drive 0", result is Slot 5. 14-Sep 20:15 elizabeth-sd: 3307 Issuing autochanger "unload slot 5, drive 0" command. 14-Sep 20:16 elizabeth-sd: 3304 Issuing autochanger "load slot 1, drive 0" command. 14-Sep 20:17 elizabeth-sd: 3305 Autochanger "load slot 1, drive 0", status is OK. 14-Sep 20:17 elizabeth-sd: 3301 Issuing autochanger "loaded drive 0" command. 14-Sep 20:17 elizabeth-sd: 3302 Autochanger "loaded drive 0", result is Slot 1. 14-Sep 20:17 elizabeth-sd: Volume "Full-B1" previously written, moving to end of data. 14-Sep 20:18 elizabeth-sd: BackupCatalog.2006-09-14_19.40.00 Error: I cannot write on Volume "Full-B1" because: The number of files mismatch! Volume=10 Catalog=9 14-Sep 20:18 elizabeth-sd: Marking Volume "Full-B1" in Error in Catalog. 14-Sep 20:18 elizabeth-sd: 3301 Issuing autochanger "loaded drive 0" command. 14-Sep 20:18 elizabeth-sd: 3302 Autochanger "loaded drive 0", result is Slot 1. 14-Sep 20:18 elizabeth-sd: 3307 Issuing autochanger "unload slot 1, drive 0" command. 14-Sep 20:19 elizabeth-sd: 3304 Issuing autochanger "load slot 2, drive 0" command. 14-Sep 20:19 elizabeth-sd: 3305 Autochanger "load slot 2, drive 0", status is OK. 14-Sep 20:19 elizabeth-sd: 3301 Issuing autochanger "loaded drive 0" command. 14-Sep 20:19 elizabeth-sd: 3302 Autochanger "loaded drive 0", result is Slot 2. 14-Sep 20:20 elizabeth-sd: Wrote label to prelabeled Volume "Full-B2" on device "DDS" (/dev/nst0) 14-Sep 20:20 elizabeth-sd: Spooling data ------------------------------------------------------------------------- Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642 _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
