-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
But you did not expect that to work properly, because the previous job
failed, right?
Does everything work properly if the previous job did not fail? I
actually have never had this happen with my setup -- if the previous job
fails, I know about it and take care of it prior to the next backup.
---- _ _ _ _ ___ _ _ _
|Y#| | | |\/| | \ |\ | | |Ryan Novosielski - User Support Spec. III
|$&| |__| | | |__/ | \| _| |[EMAIL PROTECTED] - 973/972.0922 (2-0922)
\__/ Univ. of Med. and Dent.|IST/AST - NJMS Medical Science Bldg - C630
Peter Sjoberg wrote:
> On Fri, 2006-05-05 at 21:17 -0400, Peter Sjoberg wrote:
>> On Fri, 2006-05-05 at 16:06 -0400, Ryan Novosielski wrote:
> It absolutely does work, at least with single drives. I do this
> currently (writing larger fulls to a DAT72 drive and smaller
> incrementals to a DDS4).
>
> Here's an example:
>
> Schedule {
> Name = "UMD-F13T-Inc"
> Run = Level=Full Storage=helios_DAT72 1st,3rd tue at 21:00
> Run = Level=Incremental 1st,3rd mon,wed-fri at 23:00
> Run = Level=Incremental 2nd,4th-5th mon-fri at 23:00
> }
>>> I was looking in different places but I guess Job and Pool was the wrong
>>> place.
>>> I will try this and see how it works out but after reading the doc it
>>> seems like a good change that it will work.
>>>
>>> Based on Kerns' comment I guess it's some bug related to multiple
>>> autochangers that's fixed with the latest release so I will also upgrade
>>> to 1.38.9 before giving it a try.
>> Tried it out and the bad news is that it doesn't work for several
>> reasons, some minor and some major and in the end I think it's some work
>> left to do and bugs to fix in this area before I can really use it.
>
>
>> Setup:
>> Schedule {
>> Name = "MonthlyCycle"
>> Run = Full Storage=ADIC 2nd sun at 0:35
>> Run = Differential Storage=TL892 1st,3rd-5th sun at 3:05
>> Run = Incremental Storage=TL892 mon-sat at 3:05
>> }
>> in ADIC I loaded 22 tapes from the Full pool
>> in TL892 I loaded a mix of DIFF and INC tapes
>> I did update slots on both autochangers
>
>> Directly I then issued "run Backup_janeway Level=Full yes" and followed
>> what was going on.
>> It took a look on TL892 and then loaded a tape, this when I expected it
>> to load it in ADIC. Of course this strange behavior can be expected
>> since the storage is defined in the scedule and not the pool, it doesn't
>> really know the connection and just use the default job storage which
>> happens to be TL892. I guess it could have know that all the "FUL" tapes
>> where in the other loader by looking in the database record but I guess
>> the default job storage takes precedence.
>> I then issued "run Backup_lister Level=Full Storage=ADIC yes" and this
>> time it loaded a tape in ADIC (same slot as it did on load earlier
>> TL892) and completed a full backup.
>> I now realized that if an incr/diff is upgraded to Full it will still
>> try to use the wrong autochanger so I would have to be careful in that
>> area but this would still not be a show stopper for me so I left it to
>> run a normal incremental over night.
>> In the morning I find that all jobs failed.
>> "Backup_janeway" starts of with "Prior failed job found. Upgrading to
>> Full". Since the test before failed it's upgraded to full and my
>> suspicions are confirmed, it still try to use TL892. The rest of that
>> job error is
>
>> 06-May 03:05 sisko-dir: Prior failed job found. Upgrading to Full.
>> 06-May 03:05 sisko-dir: Start Backup JobId 8181,
>> Job=Backup_janeway.2006-05-06_03.05.00
>> 06-May 03:05 sisko-sd: 3301 Issuing autochanger "loaded drive 0" command.
>> 06-May 03:05 sisko-sd: 3302 Autochanger "loaded drive 0", result: nothing
>> loaded.
>> 06-May 03:05 sisko-sd: 3304 Issuing autochanger "load slot 3, drive 0"
>> command.
>> 06-May 03:09 sisko-sd: 3305 Autochanger "load slot 3, drive 0", status is OK.
>> 06-May 03:09 sisko-sd: 3301 Issuing autochanger "loaded drive 0" command.
>> 06-May 03:09 sisko-sd: 3302 Autochanger "loaded drive 0", result is Slot 3.
>> 06-May 03:14 sisko-sd: Backup_janeway.2006-05-06_03.05.00 Fatal error:
>> dev.c:362 dev.c:356 Unable to open device "TL0" (/dev/scsi/nsth5-1c0i4l0):
>> ERR=Device or resource busy
>> 06-May 03:14 sisko-sd: Backup_janeway.2006-05-06_03.05.00 Fatal error:
>> device.c:296 Unable to open device "TL0" (/dev/scsi/nsth5-1c0i4l0):
>> ERR=dev.c:356 Unable to open device "TL0" (/dev/scsi/nsth5-1c0i4l0):
>> ERR=Device or resource busy
>
>> 06-May 03:14 janeway-fd: Backup_janeway.2006-05-06_03.05.00 Fatal error:
>> job.c:1602 Bad response to Append Data command. Wanted 3000 OK data
>> , got 3903 Error append data
>
>> So it fails some issue around the device being busy. After all, I had
>> several jobs kicked off at the same time and it seems like they all
>> failed to open the device.
>
>> 06-May 03:14 sisko-dir: Start Backup JobId 8185,
>> Job=Backup_lister.2006-05-06_03.05.04
>> 06-May 03:34 sisko-sd: 3301 Issuing autochanger "loaded drive 0" command.
>> 06-May 03:34 sisko-sd: 3302 Autochanger "loaded drive 0", result is Slot 6.
>> 06-May 03:34 sisko-sd: 3301 Issuing autochanger "loaded drive 0" command.
>> 06-May 03:34 sisko-sd: 3302 Autochanger "loaded drive 0", result is Slot 6.
>> 06-May 03:39 sisko-sd: Backup_lister.2006-05-06_03.05.04 Fatal error:
>> dev.c:362 dev.c:356 Unable to open device "TL0" (/dev/scsi/nsth5-1c0i4l0):
>> ERR=Device or resource busy
>> 06-May 03:39 sisko-sd: Backup_lister.2006-05-06_03.05.04 Fatal error:
>> device.c:296 Unable to open device "TL0" (/dev/scsi/nsth5-1c0i4l0):
>> ERR=dev.c:356 Unable to open device "TL0" (/dev/scsi/nsth5-1c0i4l0):
>> ERR=Device or resource busy
>
>> 06-May 03:39 lister-fd: Backup_lister.2006-05-06_03.05.04 Fatal error:
>> job.c:1602 Bad response to Append Data command. Wanted 3000 OK data
>> , got 3903 Error append data
>
>
>> At the moment I thing going back to only using one tapeloader is the
>> only thing I can do.
>
>>> Thanks
>>>
>>> /ps
> I'm guessing I don't have Storage labeled for incrementals because the
> other drive is the default.
>
> ---- _ _ _ _ ___ _ _ _
> |Y#| | | |\/| | \ |\ | | |Ryan Novosielski - User Support Spec. III
> |$&| |__| | | |__/ | \| _| |[EMAIL PROTECTED] - 973/972.0922 (2-0922)
> \__/ Univ. of Med. and Dent.|IST/AST - NJMS Medical Science Bldg - C630
>
>
> Peter Sjoberg wrote:
>>>>> I'm asking for suggestions on how I can best utilize two tape libraries.
>>>>> One tape library is a 10 x DLT7000
>>>>> The other is 15 x DLT8000
>>>>>
>>>>> At first I was thinking of putting the FULL backup to the bigger library
>>>>> and run diff and inc to the smaller one but I don't know the best way to
>>>>> do that.
>>>>> I kind of expected to be able to do that in one single job but that
>>>>> doesn't seem to be possible to have one storage for full and another for
>>>>> diff/inc.
>>>>> Setting up separate jobs won't work since then the diff/inc job won't
>>>>> find the "Full" to base it on.
>>>>>
>>>>> Any suggestions ?
>>>>>
>>>>>
>>>>> In case it matters, I'm running Bacula 1.38.5
>>>>>
>>>>>
>>>>>
>>
>> -------------------------------------------------------
>> Using Tomcat but need to do more? Need to support web services, security?
>> Get stuff done quickly with pre-integrated technology to make your job easier
>> Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
>> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
>> _______________________________________________
>> Bacula-users mailing list
>> Bacula-users@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/bacula-users
> -------------------------------------------------------
> Using Tomcat but need to do more? Need to support web services, security?
> Get stuff done quickly with pre-integrated technology to make your job easier
> Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
> http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> _______________________________________________
> Bacula-users mailing list
> Bacula-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bacula-users
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.2.2 (MingW32)
iD8DBQFEX5NJmb+gadEcsb4RApAQAJ4jqM+GO7OQHy5aJl0o83UeFSli/wCgjlYJ
CzYUB0gevm/ZgnPnRffH2mo=
=LFqv
-----END PGP SIGNATURE-----
-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
