Hello Jonas, Thanks for the feedback.
I will add your example to the manual. Thanks. :-) On Wednesday 30 November 2005 19:45, Jonas Mixter wrote: > Hi! > I found a solution to my problem below... I'm posting the solution to > the list so it might help others. > > Since the problem I had was that the block size settings were different > on my new and my old machine I checked the settings on the old machine > and used the same settings on the new one. > Simple? Yes, when one knows how to do it... :-) > > Using "mt -f /dev/nst0 status" on the old machine, I got the setting for > the tape-station (512 in my case) > The command "bls -c /etc/bacula/bacula-sd.conf -k -V \* /dev/nst0" shows > me the blocksize used on the tape (64512 for me). I could run this check > on the new machine too. > > By using Minimum and Maximum block size in bacula-sd.conf I'm forcing > bacula to use a fixed block size. > I also set my tape drive on the new machine using "mt -f /dev/nst0 > defblksize 512" > > I could now use bscan to recreate the database records for my tapes, and > then restore them. > > Don't forget to change the settings back to variable blocksize when done! > Run "mt -f /dev/nst0 defblksize 0" > And remove the block size directives from bacula-sd.conf > > Thank you Kern for a great program and wonderful support! > > Best regards, Jonas Mixter > > On 2005-11-28 23:31, Kern Sibbald wrote: > >On Monday 28 November 2005 17:25, Jonas Mixter wrote: > >>Hi again... > >>Thanks for your quick answer! I understand the details of my problem > >>better now... > >>I do have some more questions though. > >> > >>>>28-Nov 14:42 bscan: bscan Error: block.c:264 Volume data error at 0:1! > >>>>Wanted ID: "BB02", got "". Buffer discarded. > >>>> > >>>>...and then bscan exits. > >>> > >>>You should try running the btape "test" command. > >> > >>I've tested my drive when installing this new machine, but ran the > >>command again just to be sure. It says all is OK... > >> > >>I also ran the command on the old machine and it failed! > >>I've been using this installation for over a year so I cannot recall if > >>I ever ran the bscan test when installing (probably not I'm afraid). I > >>can both backup and restore on the old machine though... (Tried to > >>restore some files from one of the old tape a few minutes ago, all went > >>fine.) > >> > >>>>All the old tapes are written using bacula 1.34.2 (or perhaps an even > >>>>older version) and I'm now using 1.36.2 (shipped with Debian). > >>>>Is there a difference in the format on the tapes? > >>> > >>>No, not that I am aware of. However, Bacula does set your tape drive to > >>>variable block format if that is what your Device statement specifies, > >>>whereas 1.34.2 does not do that. Depending on how your machine > >>>initializes the tape drive, this could create some incompatibilities ... > >>>The manual goes into these questions in more detail and suggests some > >>>ways of dealing with it. > >> > >>I read http://bacula.org/rel-manual/Testing_Your_Tape_Drive.html and > >>wonder if I could see if variable or fixed blocksize were used on the > >>old machine. > > > >The tape testing manual tells you how to determine that question. In > > general if you have tapeinfo and mt you should be able to find out, or > > possibly by looking at the output from one of the variations of the bls > > command. > > > >>I also wonder if I could specify a fixed blocksize in > >>bacula-sd.conf > > > >Yes, of course. > > > >>to be able to restore from the old tapes. > > > >Who knows? There are so many variables of systems and tape drives and > >options ... > > > >>I cannot change the bootstrap file as suggested since the volume is not > >>in the catalog. > > > >A bootstrap file is an ASCII file that anyone can edit. It is not directly > >tied to the catalog. If you read the restore manual as I suggested, it is > >explained there. > > > >>I need to use bscan to get it into the catalog first... > > > >That is *one* way of doing things ... > > > >>Are my old tapes useless or is there any way to use them on the new > >>machine? > > > >I cannot ansswer that. See my answer to the same question above. > > > >>If it's not possible to read the tapes on the new machine, is it a > >>workable solution to use bcopy to get the data into a file on the old > >>machine and then copy it all back to tape on the new machine? > > > >Perhaps, but personally, I would restore the files to disk, and move the > >restore directory to the new machine. -- Best regards, Kern ("> /\ V_V ------------------------------------------------------- This SF.net email is sponsored by: Splunk Inc. Do you grep through log files for problems? Stop! Download the new AJAX search engine that makes searching your log files as easy as surfing the web. DOWNLOAD SPLUNK! http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click _______________________________________________ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
