On Monday 21 November 2005 04:15, AltGrendel wrote:
> I hope this isn't bringing up an old thread, if it is just point me in
> the right direction.
>
> I have an RH system (RH9 upgraded to ES3, upgraded to the 2.6.14
> kernel). I'm running bacula 1.38.1 compiled from source. For backup
> hardware, I have a ADIC VLS DLT400 that backs up a Win2k v1.38.1 client
> over the network.
>
> All of the following was done on the same tape:
> btape test command, including autochanger test, works fine.
> btape fill test works fine.
> the client backup will run, but the job will only write the first 60
> to 100 Mb to tape, error out, mark the tape full, then ask for another
> tape.
>
> Here is the error I get on the console:
>
> st0: Block limits 1 - 16777215 bytes.
> (scsi1:A:2:0): Unexpected busfree in Data-out phase
> SEQADDR == 0xa0
> st0: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).
After this occurs, before doing anything else, try manually issuing:
tapeinfo -f /dev/sg0
where you replace sg0 with your tape control device name.
>
> --- mt status output
>
> # mt -f /dev/nst0 status
> SCSI 2 tape drive:
> File number=21, block number=0, partition=0.
> Tape block size 0 bytes. Density code 0x1a (DLT 20GB).
> Soft error count since last status=0
> General status bits on (81010000):
> EOF ONLINE IM_REP_EN
>
> --- bacula-sd.conf listing
>
> Autochanger {
> Name = ADIC #
> Description = "ADIC VLS DLT400"
> Device = AUTO-DLT
> Changer Device = /dev/sg4
> Changer Command = "/etc/bacula/mtx-changer %c %o %S %a %d"
> }
>
> Device {
> Name = AUTO-DLT #
> Description = "ADIC DLT4000"
> Media Type = DLT-auto
> Archive Device = /dev/nst0
> AutomaticMount = yes; # when device opened, read it
> AlwaysOpen = yes;
> RemovableMedia = yes;
> RandomAccess = no;
> AutoChanger = yes;
> LabelMedia = no;
> Alert Command = "sh -c 'tapeinfo -f %c |grep TapeAlert|cat'"
> Maximum Spool Size = 1895219200
> Maximum Job Spool Size = 1695219200
> Spool Directory = /var/spool/bacula
> }
>
> <snip>
> --- bacula-dir.conf listing
> <snip>
> # Definition of ADIC VLS DLT400 tape storage device
> JobDefs {
> Name = "ScorchFullBackup"
> Type = Backup
> Level = Full
> Client = Scorch-fd
> FileSet = "Full Win Set"
> # Schedule = "MonthlyCycle"
> Storage = ADIC
> Messages = Standard
> Pool = Autochanger
> Priority = 10
> }
>
> <snip>
>
> Job {
> Name = "Scorch-backup"
> JobDefs = "ScorchFullBackup"
> SpoolData = yes
> Write Bootstrap = "/var/bacula/Client1.bsr"
> }
>
> <snip>
>
> Storage {
> Name = ADIC
> # Do not use "localhost" here
> Address = alpha # N.B. Use a fully qualified name here
> SDPort = 9103
> Password = "*****************" # password for Storage daemon
> Device = ADIC
> Media Type = DLT-auto
> Autochanger = yes
> }
>
> I do rememeber some discussion of problems with the 2.6 series kernel, I
> don't know if this is a symptom of that. If there is any other output I
> can supply that might help diagnosis, please let me know. Any other
> suggestions for correcting this are welcome.
>
> Thanks for you time.
>
> AltGrendel
>
>
> -------------------------------------------------------
> This SF.Net email is sponsored by the JBoss Inc. Get Certified Today
> Register for a JBoss Training Course. Free Certification Exam
> for All Training Attendees Through End of 2005. For more info visit:
> http://ads.osdn.com/?ad_id=7628&alloc_id=16845&op=click
> _______________________________________________
> Bacula-users mailing list
> Bacula-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bacula-users
--
Best regards,
Kern
(">
/\
V_V
-------------------------------------------------------
This SF.Net email is sponsored by the JBoss Inc. Get Certified Today
Register for a JBoss Training Course. Free Certification Exam
for All Training Attendees Through End of 2005. For more info visit:
http://ads.osdn.com/?ad_id=7628&alloc_id=16845&op=click
_______________________________________________
Bacula-users mailing list
Bacula-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bacula-users
