On Tue, 30 May 2006, leonimar cape wrote: > I am getting silence/no audio on my second E1. I am > using a A104D card. The called party was ringing but I > only got silence when the call is answered. Can > someone please help me.
I can try... I guess there is something wrong with your 'firstcic' directives in ss7.conf. > Below is my ss7.conf > > > [linkset-siuc] > enabled => yes > enable_st => no > use_connect => no > hunting_policy => even_mru > subservice => 8 > language => en > context => outrt-003-SPRINT > ;context => from-pstn > t35 => 4000,st > ;context => ext-did > > [link-l1] > linkset => siuc > channels => 1-15,17-31 > schannel => 16 > firstcic => 1 > ; echocancel: allways | 31speech | no > echocancel=allways > ; echocan_taps: 32 | 64 | 128 | 256 > echocan_taps=128 > ; echocan_train: between 10ms and 1000ms > echocan_train=100 > enabled => yes > > > [link-l2] > linkset => siuc > channels => 1-15,17-30 > schannel => > firstcic => 32 ; It should be: channels => 1-31 schannel => firstcic => 33 > ; echocancel: allways | 31speech | no > ;echocancel=allways > ; echocan_taps: 32 | 64 | 128 | 256 > ;echocan_taps=128 > ; echocan_train: between 10ms and 1000ms > ;echocan_train=100 > enabled => yes > > [host-asterisk1.local] > enabled => yes > opc => 0x3 > dpc => siuc:0x28fe > links => l1:1,l2:2 > --- leonimar cape <[EMAIL PROTECTED]> wrote: > >> Can please someone help on how does the CIC mapping of >> the chan_ss7 works especially for configuring more >> than 1 e1. Does it support skip on the timeslot 16? >From my experience, it usually helps to write out all the cic's to undestand >the mapping. The next 4 lines shows the cic's on 4 E1's. (The lines are long, so your mail-reader will probably ruin the alignment. To help you re-align, the pipe-chars '|' should be vertically alligned.) 0 | 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 |33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 |65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 |97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 The first column are the timeslot where a sync. signal is present. The 'firstcic' directive should be the number in the second column (right after the '|') 1, 33, 65 and 97. Signalling timeslots are the column where the first '16' is in (16, 48, 80 and 112). Usually you will only use 16 for signalling and then 48, 80 and 112 for audio. Now comes the tricky part.. The "channels" and "schannels" directive refers to cic's at the particular E1 so they should be less than or equal to 31 and more than or equal to 1. In contrary, the 'firstcic' directive refers to all the E1's so it should typically be 1, 33, 65 or 97. I hope this made it a little more clear for everybody on <[email protected]>, how to configure channel mappings for chan_ss7. I know channel and cic mapping are not the most easy subject in the world... (and Im not the best teacher in the world). >> I think my wrong CIC mapping is the reason why I get >> silence on my second, third and forth e1. Also, may I >> ask if the next release will support routing interms >> of e1/t1 and not only by linkset? I think this will be >> usefull specially if you are interconnecting to a >> telco switch that uses trunk group for segregating >> traffic. No, the next version will not support routing. We (Sifira) does not need it right now, so we do not have plans to make it. However, anybody are very welcome to send us a patch, which includes routing :) Mvh. Jacob -- Jacob Tinning System Developer SIFIRA A/S _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
