Hello arm@
[dmesg is attached]
What's "strange" about it is that the output at the console
gets to the point where normally there'd be a login prompt.
So the date gets displayed, but there's no "login:"
The console [0] worked as expected before the upgrade.
There is the following in /etc/boot.conf
set tty com0 115200
set image /bsd.no-uhid
I remove the set image line and reboot in order to upgrade.
After the upgrade happens, I have to ssh in (because no login: at console)
and become root, then I run this:
# printf 'disable uhidev\ndisable upd\nquit\n' | config -e -o /bsd.no-uhid /bsd
then add the set image line then reboot. [1]
But the problem I'm describing happens regardless of what kernel is used.
The difference is this worked in 7.1.
I'm not sure where to check. The upgrade was without errors and an interactive
sysmerge was solely for /etc/mail/aliases.
[0] this is a ttl to usb cable. The ttl end is on the rpi4 and the usb2 end
plugs into a rpi1b
[1] this is in order to use sysutils/apcupsd
[2] have also tried 'set tty com0' and 'set tty fb0' same result.
TIA,
OpenBSD 7.2 (GENERIC.MP) #0: Wed Oct 26 11:07:43 MDT 2022
r...@syspatch-72-arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 8418877440 (8028MB)
avail mem = 8125861888 (7749MB)
random: good seed from bootblocks
mainbus0 at root: Raspberry Pi 4 Model B Rev 1.4
cpu0 at mainbus0 mpidr 0: ARM Cortex-A72 r0p3
cpu0: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu0: 1024KB 64b/line 16-way L2 cache
cpu0: CRC32,ASID16
cpu1 at mainbus0 mpidr 1: ARM Cortex-A72 r0p3
cpu1: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu1: 1024KB 64b/line 16-way L2 cache
cpu1: CRC32,ASID16
cpu2 at mainbus0 mpidr 2: ARM Cortex-A72 r0p3
cpu2: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu2: 1024KB 64b/line 16-way L2 cache
cpu2: CRC32,ASID16
cpu3 at mainbus0 mpidr 3: ARM Cortex-A72 r0p3
cpu3: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
cpu3: 1024KB 64b/line 16-way L2 cache
cpu3: CRC32,ASID16
efi0 at mainbus0: UEFI 2.8
efi0: Das U-Boot rev 0x20211000
apm0 at mainbus0
"system" at mainbus0 not configured
"axi" at mainbus0 not configured
simplebus0 at mainbus0: "soc"
bcmclock0 at simplebus0
bcmmbox0 at simplebus0
bcmgpio0 at simplebus0
bcmaux0 at simplebus0
ampintc0 at simplebus0 nirq 256, ncpu 4 ipi: 0, 1, 2: "interrupt-controller"
bcmtmon0 at simplebus0
bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA6 DMA7 DMA8 DMA9 DMA10
"timer" at simplebus0 not configured
pluart0 at simplebus0: rev 2, 16 byte fifo
pluart0: console
"local_intc" at simplebus0 not configured
bcmdog0 at simplebus0
bcmirng0 at simplebus0
"firmware" at simplebus0 not configured
"power" at simplebus0 not configured
"mailbox" at simplebus0 not configured
sdhc0 at simplebus0
sdhc0: SDHC 3.0, 250 MHz base clock
sdmmc0 at sdhc0: 4-bit, sd high-speed, mmc high-speed
"gpiomem" at simplebus0 not configured
"fb" at simplebus0 not configured
"vcsm" at simplebus0 not configured
"clocks" at mainbus0 not configured
"phy" at mainbus0 not configured
"clk-27M" at mainbus0 not configured
"clk-108M" at mainbus0 not configured
simplebus1 at mainbus0: "emmc2bus"
sdhc1 at simplebus1
sdhc1: SDHC 3.0, 100 MHz base clock
sdmmc1 at sdhc1: 8-bit, sd high-speed, mmc high-speed, ddr52, dma
"arm-pmu" at mainbus0 not configured
agtimer0 at mainbus0: 54000 kHz
simplebus2 at mainbus0: "scb"
bcmpcie0 at simplebus2
pci0 at bcmpcie0
ppb0 at pci0 dev 0 function 0 "Broadcom BCM2711" rev 0x10
pci1 at ppb0 bus 1
xhci0 at pci1 dev 0 function 0 "VIA VL805 xHCI" rev 0x01: intx, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "VIA xHCI root hub" rev 3.00/1.00
addr 1
bse0 at simplebus2: address dc:a6:32:e2:48:fc
brgphy0 at bse0 phy 1: BCM54210E 10/100/1000baseT PHY, rev. 2
"dma" at simplebus2 not configured
"hevc-decoder" at simplebus2 not configured
"rpivid-local-intc" at simplebus2 not configured
"h264-decoder" at simplebus2 not configured
"vp9-decoder" at simplebus2 not configured
gpioleds0 at mainbus0: "led0", "led1"
"sd_io_1v8_reg" at mainbus0 not configured
"sd_vcc_reg" at mainbus0 not configured
"fixedregulator_3v3" at mainbus0 not configured
"fixedregulator_5v0" at mainbus0 not configured
simplebus3 at mainbus0: "v3dbus"
"bootloader" at mainbus0 not configured
sdhc_sdclk_frequency_select: command in progress
sdhc_sdclk_frequency_select: command in progress
sdmmc0: can't enable card
sdhc_sdclk_frequency_select: command in progress
sdmmc1: can't enable card
uhub1 at uhub0 port 1 configuration 1 interface 0 "VIA Labs USB2.0 Hub" rev
2.10/4.21 addr 2
ugen0 at uhub1 port 4 "American Power Conversion Back-UPS XS 1400U FW:926.T2
.I USB FW:T2" rev 1.10/1.06 addr 3
umass0 at uhub0 port 3 configuration 1 interface 0 "USB SanDisk 3.2Gen1" rev
3.20/1.00 addr 4
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <USB, SanDisk 3.2Gen1, 1.00> removable
serial.078155958107642c2082
sd0: 117348MB, 512 bytes/sector, 240328704 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on sd0a (35543bba5048a99e.a) swap on sd0b dump on sd0b
WARNING: CHECK AND RESET THE DATE!
gpio0 at bcmgpio0: 58 pins
