I see; thank you, Stewart! Out of curiosity, what OS do OpenBSD fans run on unsupported machines?
> On Oct 13, 2020, at 13:52, Stuart Henderson <s...@spacehopper.org> wrote: > > > IIRC the 3B+ has a different USB controller and there are some differences > with the SD controller, those devices are not expected to work on OpenBSD on > the 3B+. > > Pi 4 and the non-+ version of the Pi 3 work pretty well. > > -- > Sent from a phone, apologies for poor formatting. > >> On 13 October 2020 17:51:10 Patrick Coppock <pcoppo...@icloud.com> wrote: >> >> I have written the arm64 miniroot to a USB flash drive and successfully >> booted the installer. After I type 's' to get a shell and run "ifconfig", >> neither the Ethernet nor Wi-Fi interfaces are listed. According to >> https://www.openbsd.org/arm64.html, the interfaces are both supported. Why >> are the interfaces not showing up in "ifconfig" output? >> >> >> # ifconfig >> lo0: flags=8008<LOOPBACK,MULTICAST> mtu 32768 >> llprio 3 >> groups: lo >> # dmesg >> OpenBSD 6.7 (RAMDISK) #572: Thu May 7 14:08:02 MDT 2020 >> dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK >> real mem = 958050304 (913MB) >> avail mem = 895766528 (854MB) >> mainbus0 at root: Raspberry Pi 3 Model B Plus Rev 1.3 >> cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 >> cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache >> cpu0: 512KB 64b/line 16-way L2 cache >> efi0 at mainbus0: UEFI 2.8 >> efi0: Das U-Boot rev 0x20200100 >> simplefb0 at mainbus0: 656x416, 32bpp >> wsdisplay0 at simplefb0 >> wsdisplay0: screen 0 added (std, vt100 emulation) >> "system" at mainbus0 not configured >> "axi" at mainbus0 not configured >> simplebus0 at mainbus0: "soc" >> bcmdmac0 at simplebus0: DMA0 DMA2 DMA4 DMA5 DMA8 DMA9 DMA10 >> bcmclock0 at simplebus0 >> bcmmbox0 at simplebus0 >> bcmgpio0 at simplebus0 >> bcmaux0 at simplebus0 >> bcmintc0 at simplebus0 >> bcmdog0 at simplebus0 >> bcmrng0 at simplebus0 >> pluart0 at simplebus0: console >> bcmsdhost0 at simplebus0: 250 MHz base clock >> sdmmc0 at bcmsdhost0: 4-bit, sd high-speed, mmc high-speed, dma >> "dsi" at simplebus0 not configured >> dwctwo0 at simplebus0 >> "thermal" at simplebus0 not configured >> "local_intc" at simplebus0 not configured >> sdhc0 at simplebus0 >> sdhc0: SDHC 3.0, 200 MHz base clock >> sdmmc1 at sdhc0: 4-bit, sd high-speed, mmc high-speed >> simplebus1 at simplebus0: "firmware" >> "expgpio" at simplebus1 not configured >> "power" at simplebus0 not configured >> "mailbox" at simplebus0 not configured >> "gpiomem" at simplebus0 not configured >> "fb" at simplebus0 not configured >> "vcsm" at simplebus0 not configured >> simplebus2 at mainbus0: "clocks" >> "clock" at simplebus2 not configured >> "clock" at simplebus2 not configured >> "phy" at mainbus0 not configured >> "arm-pmu" at mainbus0 not configured >> agtimer0 at mainbus0: tick rate 19200 KHz >> "leds" at mainbus0 not configured >> "fixedregulator_3v3" at mainbus0 not configured >> "fixedregulator_5v0" at mainbus0 not configured >> usb0 at dwctwo0: USB revision 2.0 >> sdmmc0: can't enable card >> uhub0 at usb0 configuration 1 interface 0 "Broadcom DWC2 root hub" rev >> 2.00/1.00 addr 1 >> uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems >> product 0x2514" rev 2.00/b.b3 addr 2 >> uhub2 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems >> product 0x2514" rev 2.00/b.b3 addr 3 >> umass0 at uhub2 port 2 configuration 1 interface 0 "Lexar USB Flash Drive" >> rev 2.00/11.00 addr 4 >> umass0: using SCSI over Bulk-Only >> scsibus0 at umass0: 2 targets, initiator 0 >> sd0 at scsibus0 targ 1 lun 0: <Lexar, USB Flash Drive, 1100> removable >> serial.05dca81dJ27H3EJCWEBZ >> sd0: 15263MB, 512 bytes/sector, 31258624 sectors >> sdmmc1: bad CIS ptr 0 >> sdmmc1: can't read CIS >> sdmmc1: i/o init failed >> sdmmc1: bad CIS ptr 0 >> sdmmc1: can't read CIS >> sdmmc1: i/o init failed >> sdmmc1: bad CIS ptr 0 >> sdmmc1: can't read CIS >> sdmmc1: i/o init failed >> bwfm0 at sdmmc1 function 1 >> bwfm0: cannot enable function 1 >> manufacturer 0x02d0, product 0xa9a6 at sdmmc1 function 2 not configured >> manufacturer 0x02d0, product 0xa9a6 at sdmmc1 function 3 not configured >> softraid0 at root >> scsibus1 at softraid0: 256 targets >> bootfile: sd0a:/bsd >> boot device: sd0 >> root on rd0a swap on rd0b dump on rd0b >> WARNING: CHECK AND RESET THE DATE! >> gpio at bcmgpio0 not configured >> # > >
