On Mon, Jul 13, 2020 at 11:26:12PM +0200, Sebastian Reitenbach wrote:
> Hi,
>
> eventually got my hands on a PinebookPro, installation went fine.
>
> Prepard SD card for initial installation alike:
>
> mount /dev/${DEV}i /mnt
> mkdir /mnt/rockchip
> cp /usr/local/share/dtb/arm64/rockchip/rk3399-pinebook-pro.dtb
> /mnt/rockchip
> umount /mnt
U-Boot includes a builtin dtb in this case, why use the linux one?
> dd if=/usr/local/share/u-boot/pinebook-pro-rk3399/idbloader.img
> of=/dev/${DEV}c seek=64
> dd if=/usr/local/share/u-boot/pinebook-pro-rk3399/u-boot.itb
> of=/dev/${DEV}c seek=16384
>
> DTB and u-boot files are from following packages:
> dtb-5.7p0 Device Tree Blobs
> u-boot-aarch64-2020.07 U-Boot firmware
You are not using U-Boot 2020.07 in your dmesg.
"U-Boot 2020.01-4-g908d441fef (Jan 20 2020 - 05:02:39 +0000) Manjaro ARM"
>
> looking at other Pinebook related threats, found that issuing
> set tty fb0
>
> at the boot> prompt, or put it in /etc/boot.conf might help, but to no avail.
>
> U-Boot SPL 2020.01-4-g908d441fef (Jan 20 2020 - 05:02:39 +0000)
> Trying to boot from MMC2
>
> U-Boot 2020.01-4-g908d441fef (Jan 20 2020 - 05:02:39 +0000) Manjaro ARM
> Model: Pine64 Pinebook Pro
> DRAM: 3.9 GiB
> PMIC: RK808
> MMC: dwmmc@fe320000: 1, sdhci@fe330000: 0
> In: serial@ff1a0000
> Out: serial@ff1a0000
> Err: serial@ff1a0000
> Model: Pine64 Pinebook Pro
> ## Error: Can't overwrite "serial#"
> ## Error inserting "serial#" variable, errno=1
> rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> Net: No ethernet found.
> Hit any key to stop autoboot: 0
> Card did not respond to voltage select!
> starting USB...
> Bus usb@fe380000: USB EHCI 1.00
> Bus usb@fe3c0000: USB EHCI 1.00
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> Bus dwc3: Register 2000140 NbrPorts 2
> Starting the controller
> USB XHCI 1.10
> scanning bus usb@fe380000 for devices... 1 USB Device(s) found
> scanning bus usb@fe3c0000 for devices...
> Warning: asix_eth MAC addresses don't match:
> Address in ROM is 00:60:6e:d5:a1:eb
> Address in environment is 7e:f3:8b:24:02:37
> 4 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
> scanning bus dwc3 for devices... 1 USB Device(s) found
> scanning usb for storage devices... 0 Storage Device(s) found
>
> Device 0: unknown device
> switch to partitions #0, OK
> mmc0(part 0) is current device
> Scanning mmc 0:1...
> Found EFI removable media binary efi/boot/bootaa64.efi
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> Card did not respond to voltage select!
> Scanning disk dw...@fe320000.blk...
> Disk dw...@fe320000.blk not ready
> Scanning disk sd...@fe330000.blk...
> ** Unrecognized filesystem type **
> Found 3 disks
> BootOrder not defined
> EFI boot manager: Cannot load any image
> 169352 bytes read in 35 ms (4.6 MiB/s)
> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> disks: sd0*
> >> OpenBSD/arm64 BOOTAA64 1.2
> switching console to fb0
> ^^^^
> this is from having set tty fb0 in /etc/boot.conf
>
> >> OpenBSD/arm64 BOOTAA64 1.2
> boot>
> booting sd0a:/bsd: 8494440+1714392+551888+791984
> [597435+109+1043088+611985]=0xf
> 6e498
> Host not halted after 16000 microseconds.
> type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8
> type 0x7 pa 0x4200000 va 0x4200000 pages 0x3eeb attr 0x8
> type 0x4 pa 0x80eb000 va 0x80eb000 pages 0x2a attr 0x8
> type 0x7 pa 0x8115000 va 0x8115000 pages 0xec012 attr 0x8
> type 0x2 pa 0xf4127000 va 0xf4127000 pages 0xcb8 attr 0x8
> type 0x4 pa 0xf4ddf000 va 0xf4ddf000 pages 0x1 attr 0x8
> type 0x2 pa 0xf4de0000 va 0xf4de0000 pages 0x3 attr 0x8
> type 0x7 pa 0xf4de3000 va 0xf4de3000 pages 0x1 attr 0x8
> type 0x2 pa 0xf4de4000 va 0xf4de4000 pages 0x100 attr 0x8
> type 0x1 pa 0xf4ee4000 va 0xf4ee4000 pages 0x2a attr 0x8
> type 0x0 pa 0xf4f0e000 va 0xf4f0e000 pages 0x7 attr 0x8
> type 0x4 pa 0xf4f15000 va 0xf4f15000 pages 0x1 attr 0x8
> type 0x6 pa 0xf4f16000 va 0x3593b20000 pages 0x1 attr 0x8000000000000008
> type 0x4 pa 0xf4f17000 va 0xf4f17000 pages 0x2 attr 0x8
> type 0x0 pa 0xf4f19000 va 0xf4f19000 pages 0x4 attr 0x8
> type 0x4 pa 0xf4f1d000 va 0xf4f1d000 pages 0x2 attr 0x8
> type 0x6 pa 0xf4f1f000 va 0x3593b29000 pages 0x1 attr 0x8000000000000008
> type 0x2 pa 0xf4f20000 va 0xf4f20000 pages 0x3010 attr 0x8
> type 0x5 pa 0xf7f30000 va 0x3596b3a000 pages 0x10 attr 0x8000000000000008
> type 0x2 pa 0xf7f40000 va 0xf7f40000 pages 0xc0 attr 0x8
> [ using 2253592 bytes of bsd ELF symbol table ]
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights reserved.
> Copyright (c) 1995-2020 OpenBSD. All rights reserved. https://www.OpenBSD.org
>
> OpenBSD 6.7-current (GENERIC.MP) #711: Fri Jul 10 13:46:35 MDT 2020
> dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
> real mem = 4092579840 (3902MB)
> avail mem = 3891367936 (3711MB)
> random: good seed from bootblocks
> mainbus0 at root: Pine64 Pinebook Pro
> psci0 at mainbus0: PSCI 1.1, SMCCC 1.2
> cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
> cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu0: 512KB 64b/line 16-way L2 cache
> cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
> cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu1: 512KB 64b/line 16-way L2 cache
> cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
> cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu2: 512KB 64b/line 16-way L2 cache
> cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
> cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache
> cpu3: 512KB 64b/line 16-way L2 cache
> cpu4 at mainbus0 mpidr 100: ARM Cortex-A72 r0p2
> cpu4: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu4: 1024KB 64b/line 16-way L2 cache
> cpu5 at mainbus0 mpidr 101: ARM Cortex-A72 r0p2
> cpu5: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 D-cache
> cpu5: 1024KB 64b/line 16-way L2 cache
> efi0 at mainbus0: UEFI 2.8
> efi0: Das U-Boot rev 0x20200100
> apm0 at mainbus0
> agintc0 at mainbus0 sec shift 3:3 nirq 288 nredist 6 ipi: 0, 1:
> "interrupt-controller"
> agintcmsi0 at agintc0
> syscon0 at mainbus0: "qos"
> syscon1 at mainbus0: "qos"
> syscon2 at mainbus0: "qos"
> syscon3 at mainbus0: "qos"
> syscon4 at mainbus0: "qos"
> syscon5 at mainbus0: "qos"
> syscon6 at mainbus0: "qos"
> syscon7 at mainbus0: "qos"
> syscon8 at mainbus0: "qos"
> syscon9 at mainbus0: "qos"
> syscon10 at mainbus0: "qos"
> syscon11 at mainbus0: "qos"
> syscon12 at mainbus0: "qos"
> syscon13 at mainbus0: "qos"
> syscon14 at mainbus0: "qos"
> syscon15 at mainbus0: "qos"
> syscon16 at mainbus0: "qos"
> syscon17 at mainbus0: "qos"
> syscon18 at mainbus0: "qos"
> syscon19 at mainbus0: "qos"
> syscon20 at mainbus0: "qos"
> syscon21 at mainbus0: "qos"
> syscon22 at mainbus0: "qos"
> syscon23 at mainbus0: "qos"
> syscon24 at mainbus0: "qos"
> syscon25 at mainbus0: "power-management"
> "power-controller" at syscon25 not configured
> syscon26 at mainbus0: "syscon"
> "io-domains" at syscon26 not configured
> syscon27 at mainbus0: "syscon"
> syscon28 at mainbus0: "syscon"
> rkclock0 at mainbus0
> rkclock1 at mainbus0
> syscon29 at mainbus0: "syscon"
> "io-domains" at syscon29 not configured
> "usb2-phy" at syscon29 not configured
> "usb2-phy" at syscon29 not configured
> rkemmcphy0 at syscon29
> rkpinctrl0 at mainbus0: "pinctrl"
> rkgpio0 at rkpinctrl0
> rkgpio1 at rkpinctrl0
> rkgpio2 at rkpinctrl0
> rkgpio3 at rkpinctrl0
> rkgpio4 at rkpinctrl0
> pwmreg0 at mainbus0
> "fit-images" at mainbus0 not configured
> "pmu_a53" at mainbus0 not configured
> "pmu_a72" at mainbus0 not configured
> agtimer0 at mainbus0: tick rate 24000 KHz
> "xin24m" at mainbus0 not configured
> simplebus0 at mainbus0: "amba"
> "dma-controller" at simplebus0 not configured
> "dma-controller" at simplebus0 not configured
> dwmmc0 at mainbus0: 50 MHz base clock
> sdmmc0 at dwmmc0: 4-bit, sd high-speed, mmc high-speed, dma
> sdhc0 at mainbus0
> sdhc0: SDHC 3.0, 200 MHz base clock
> sdmmc1 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma
> ehci0 at mainbus0
> usb0 at ehci0: USB revision 2.0
> uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> ohci0 at mainbus0: version 1.0
> ehci1 at mainbus0
> usb1 at ehci1: USB revision 2.0
> uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev
> 2.00/1.00 addr 1
> ohci1 at mainbus0: version 1.0
> rkdwusb0 at mainbus0: "usb"
> xhci0 at rkdwusb0, xHCI 1.10
> usb2 at xhci0: USB revision 3.0
> uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev
> 3.00/1.00 addr 1
> rkdwusb1 at mainbus0: "usb"
> xhci1 at rkdwusb1, xHCI 1.10
> usb3 at xhci1: USB revision 3.0
> uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev
> 3.00/1.00 addr 1
> "saradc" at mainbus0 not configured
> com0 at mainbus0: ns16550, no working fifo
> com0: console
> "spi" at mainbus0 not configured
> rktemp0 at mainbus0
> rkiic0 at mainbus0
> iic0 at rkiic0
> rkpmic0 at iic0 addr 0x1b: RK808
> fanpwr0 at iic0 addr 0x40: SYR827, 1.00 VDC
> fanpwr1 at iic0 addr 0x41: SYR828, 1.00 VDC
> rkiic1 at mainbus0
> iic1 at rkiic1
> fusbtc0 at iic1 addr 0x22
> rkpwm0 at mainbus0
> rkpwm1 at mainbus0
> rkpwm2 at mainbus0
> "dmc" at mainbus0 not configured
> "efuse" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "phy" at mainbus0 not configured
> "watchdog" at mainbus0 not configured
> "rktimer" at mainbus0 not configured
> "opp-table0" at mainbus0 not configured
> "opp-table1" at mainbus0 not configured
> "opp-table2" at mainbus0 not configured
> pwmbl0 at mainbus0
> "gpio-keys" at mainbus0 not configured
> "leds" at mainbus0 not configured
> "sdio-pwrseq" at mainbus0 not configured
> "vcc1v8-s3" at mainbus0 not configured
> "dc-12v" at mainbus0 not configured
> "vcc3v3-sys" at mainbus0 not configured
> "vcc5v0-host-regulator" at mainbus0 not configured
> "vcc5v0-usb3-host-regulator" at mainbus0 not configured
> "vcc3v3-s0-regulator" at mainbus0 not configured
> "vcc-sys" at mainbus0 not configured
> usb4 at ohci0: USB revision 1.0
> uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev
> 1.00/1.00 addr 1
> usb5 at ohci1: USB revision 1.0
> uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev
> 1.00/1.00 addr 1
> scsibus0 at sdmmc1: 2 targets, initiator 0
> sd0 at scsibus0 targ 1 lun 0: <Sandisk, DA4064, 0000> removable
> sd0: 59640MB, 512 bytes/sector, 122142720 sectors
> uhub6 at uhub1 port 1 configuration 1 interface 0 "Genesys Logic USB2.0 Hub"
> rev 2.00/85.36 addr 2
> axe0 at uhub6 port 1 configuration 1 interface 0 "ASIX Electronics AX88772B"
> rev 2.00/0.01 addr 3
> axe0: AX88772B, address 00:60:6e:d5:a1:eb
> ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
> 0x000ec6, model 0x0008
> uvideo0 at uhub6 port 2 configuration 1 interface 0 "Sonix Technology Co.,
> Ltd. USB Camera" rev 2.00/0.00 addr 4
> video0 at uvideo0
> uhidev0 at uhub4 port 1 configuration 1 interface 0 "HAILUCK CO.,LTD USB
> KEYBOARD" rev 1.10/1.00 addr 2
> uhidev0: iclass 3/1
> ukbd0 at uhidev0: 8 variable keys, 6 key codes
> wskbd0 at ukbd0 mux 1
> uhidev1 at uhub4 port 1 configuration 1 interface 1 "HAILUCK CO.,LTD USB
> KEYBOARD" rev 1.10/1.00 addr 2
> uhidev1: iclass 3/0, 35 report ids
> umt0 at uhidev1: clickpad, 4 contacts
> wsmouse0 at umt0 mux 0
> vscsi0 at root
> scsibus1 at vscsi0: 256 targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> bootfile: sd0a:/bsd
> boot device: sd0
> root on sd0a (fa51e58f1a688110.a) swap on sd0b dump on sd0b
>
> While the kernel boots, I see the display getting power, kind of backlight
> gets enabled,
> but otherwise, still stays dark, only not as dark as it was before.
>
> trying to start xenodm just brings the following in Xorg.0.log:
>
> cat /var/log/Xorg.0.log
> [ 97.269] (EE)
> Fatal server error:
> [ 97.269] (EE) xf86OpenConsole: No console driver found
> Supported drivers: wscons
> Check your kernel's console driver configuration and /dev entries(EE)
> [ 97.269] (EE)
> Please consult the The X.Org Foundation support
> at http://wiki.x.org
> for help.
> [ 97.269] (EE) Please also check the log file at "/var/log/Xorg.0.log" for
> additional information.
> [ 97.269] (EE)
> [ 97.275] (EE) Server terminated with error (1). Closing log file.
>
> As written by others, it should probably work, guess I'm missing something.
> Any clues?
>
> thanks,
> Sebastian
>
>
