Hello, I'm trying to install OpenBSD arm64 on ROCKPro64 4GB Single Board. Firstly 6.6 stable and later also snapshot from today.
I firstly followed this post https://github.com/krjdev/rock64_openbsd to be able boot OpenBSD from SD card. Things look ok, but during installation, I was not able to write to eMMC (bought together with board, eMMC includes Android and I was able to boot to it before stating migration to OpenBSD) I didn't found a HW jump for RW/RO mode for eMMC. I noticed different number of disks in different stages. Red led is on, but i didn't found why. I checked with IRC channel on PINE64, but no ideas there about RO eMMC and red led on. Any idea, how to made eMMC writable? My intent is to install OpenBSD to eMMC and use it from there. Please _reply to all_ as I'm not subscribed to this list. Thank you for any ideas and recommendations. Jiří $ cu -d -l /dev/cuaU0 -s 1500000 Connected to /dev/cuaU0 (speed 1500000) # dmesg OpenBSD 6.6 (RAMDISK) #257: Sat Oct 12 19:06:25 MDT 2019 dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/RAMDISK real mem = 4093161472 (3903MB) avail mem = 3891376128 (3711MB) mainbus0 at root: Pine64 RockPro64 cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 D-cache cpu0: 512KB 64b/line 16-way L2 cache efi0 at mainbus0: UEFI 2.0.5 efi0: Das U-boot rev 0x0 psci0 at mainbus0: PSCI 1.0 agintc0 at mainbus0 sec shift 3:4 nirq 288 nredist 6: "interrupt-controller" agintcmsi0 at agintc0 syscon0 at mainbus0: "qos" syscon1 at mainbus0: "qos" syscon2 at mainbus0: "qos" syscon3 at mainbus0: "qos" syscon4 at mainbus0: "qos" syscon5 at mainbus0: "qos" syscon6 at mainbus0: "qos" syscon7 at mainbus0: "qos" syscon8 at mainbus0: "qos" syscon9 at mainbus0: "qos" syscon10 at mainbus0: "qos" syscon11 at mainbus0: "qos" syscon12 at mainbus0: "qos" syscon13 at mainbus0: "qos" syscon14 at mainbus0: "qos" syscon15 at mainbus0: "qos" syscon16 at mainbus0: "qos" syscon17 at mainbus0: "qos" syscon18 at mainbus0: "qos" syscon19 at mainbus0: "qos" syscon20 at mainbus0: "qos" syscon21 at mainbus0: "qos" syscon22 at mainbus0: "qos" syscon23 at mainbus0: "qos" syscon24 at mainbus0: "qos" syscon25 at mainbus0: "power-management" "power-controller" at syscon25 not configured syscon26 at mainbus0: "syscon" "io-domains" at syscon26 not configured syscon27 at mainbus0: "syscon" syscon28 at mainbus0: "syscon" rkclock0 at mainbus0 rkclock1 at mainbus0 syscon29 at mainbus0: "syscon" "io-domains" at syscon29 not configured "usb2-phy" at syscon29 not configured "usb2-phy" at syscon29 not configured "phy" at syscon29 not configured rkpinctrl0 at mainbus0: "pinctrl" rkgpio0 at rkpinctrl0 rkgpio1 at rkpinctrl0 rkgpio2 at rkpinctrl0 rkgpio3 at rkpinctrl0 rkgpio4 at rkpinctrl0 "pmu_a53" at mainbus0 not configured "pmu_a72" at mainbus0 not configured agtimer0 at mainbus0: tick rate 24000 KHz "xin24m" at mainbus0 not configured simplebus0 at mainbus0: "amba" "dma-controller" at simplebus0 not configured "dma-controller" at simplebus0 not configured dwge0 at mainbus0: address a6:63:b8:9a:57:7c rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6 sdhc0 at mainbus0 sdhc0: SDHC 3.0, 200 MHz base clock sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma dwmmc0 at mainbus0: 50 MHz base clock sdmmc1 at dwmmc0: 4-bit, dma ehci0 at mainbus0 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci0 at mainbus0: version 1.0 ehci1 at mainbus0 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev 2.00/1.00 addr 1 ohci1 at mainbus0: version 1.0 "usb" at mainbus0 not configured "usb" at mainbus0 not configured "saradc" at mainbus0 not configured rkiic0 at mainbus0 iic0 at rkiic0 rkiic1 at mainbus0 iic1 at rkiic1 com0 at mainbus0: ns16550, no working fifo com1 at mainbus0: ns16550, no working fifo com1: console "spi" at mainbus0 not configured "thermal-zones" at mainbus0 not configured "tsadc" at mainbus0 not configured rkiic2 at mainbus0 iic2 at rkiic2 "pwm" at mainbus0 not configured "pwm" at mainbus0 not configured "dmc" at mainbus0 not configured "efuse" at mainbus0 not configured "watchdog" at mainbus0 not configured "rktimer" at mainbus0 not configured rkiic3 at mainbus0 iic3 at rkiic3 rkpmic0 at iic3 addr 0x1b: RK808 "backlight" at mainbus0 not configured "leds" at mainbus0 not configured "external-gmac-clock" at mainbus0 not configured "sdio-pwrseq" at mainbus0 not configured "vcc1v8-s0" at mainbus0 not configured "dc-12v" at mainbus0 not configured "vcc-sys" at mainbus0 not configured "vcc3v3-sys" at mainbus0 not configured "vcc5v0-host-regulator" at mainbus0 not configured "vcc5v0-typec0-en" at mainbus0 not configured "vcc-phy-regulator" at mainbus0 not configured "vdd-log" at mainbus0 not configured usb2 at ohci0: USB revision 1.0 uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 usb3 at ohci1: USB revision 1.0 uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 scsibus0 at sdmmc1: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <SD/MMC, USD, 0000> removable sd0: 3840MB, 512 bytes/sector, 7864320 sectors scsibus1 at sdmmc0: 2 targets, initiator 0 sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4128, 0000> removable sd1: 119276MB, 512 bytes/sector, 244277248 sectors softraid0 at root scsibus2 at softraid0: 256 targets bootfile: sd0a:/bsd boot device: sd0 root on rd0a swap on rd0b dump on rd0b WARNING: preposterous clock chip time WARNING: CHECK AND RESET THE DATE! # cd /dev # sh MAKEDEV sd0 # sh MAKEDEV sd1 # fdisk sd0 Disk: sd0 geometry: 489/255/63 [7864320 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- *0: 0C 2 10 9 - 2 140 10 [ 32768: 8192 ] FAT32L 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused 3: A6 2 140 11 - 4 52 48 [ 40960: 26624 ] OpenBSD # fdisk sd1 Disk: sd1 geometry: 15205/255/63 [244277248 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT # fdisk -i sd1 Do you wish to write new MBR and partition table? [n] y Writing MBR at offset 0. # fdisk sd1 Disk: sd1 geometry: 15205/255/63 [244277248 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT # disklabel sd1 # /dev/rsd1c: type: SCSI disk: SCSI disk label: Sandisk DA4128 duid: 0000000000000000 flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 255 sectors/cylinder: 16065 cylinders: 15205 total sectors: 244277248 boundstart: 0 boundend: 244277248 drivedata: 0 16 partitions: # size offset fstype [fsize bsize cpg] c: 244277248 0 unused from boot DDR Version 1.19 20190305 U-Boot SPL board init U-Boot SPL 2017.09-rockchip-ayufan-1065-g95f6152134 (Aug 26 2019 - 12:41:15) booted from SPI flash Trying to boot from SPI NOTICE: BL31: v1.3(debug):370ab80 NOTICE: BL31: Built : 09:23:41, Mar 4 2019 NOTICE: BL31: Rockchip release version: v1.1 INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3 INFO: Using opteed sec cpu_context! INFO: boot cpu mask: 0 INFO: plat_rockchip_pmu_init(1181): pd status 3e INFO: BL31: Initializing runtime services WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK ERROR: Error initializing runtime service opteed_fast INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2017.09-rockchip-ayufan-1065-g95f6152134 (Aug 26 2019 - 12:41:34 +0000) Model: Pine64 RockPro64 DRAM: 3.9 GiB DCDC_REG1@vdd_center: ; enabling DCDC_REG2@vdd_cpu_l: ; enabling DCDC_REG3@vcc_ddr: ; enabling (ret: -38) DCDC_REG4@vcc_1v8: set 1800000 uV; enabling LDO_REG1@vcc1v8_dvp: set 1800000 uV; enabling LDO_REG2@vcc3v0_touch: set 3000000 uV; enabling LDO_REG3@vcc1v8_pmu: set 1800000 uV; enabling LDO_REG4@vcc_sd: set 3300000 uV; enabling LDO_REG5@vcca3v0_codec: set 3000000 uV; enabling LDO_REG6@vcc_1v5: set 1500000 uV; enabling LDO_REG7@vcca1v8_codec: set 1800000 uV; enabling LDO_REG8@vcc_3v0: set 3000000 uV; enabling SWITCH_REG1@vcc3v3_s3: ; enabling (ret: -38) SWITCH_REG2@vcc3v3_s0: ; enabling (ret: -38) vcc1v8-s0@vcc1v8_s0: set 1800000 uV; enabling (ret: -38) dc-12v@dc_12v: set 12000000 uV; enabling (ret: -38) vcc-sys@vcc_sys: set 5000000 uV; enabling (ret: -38) vcc3v3-sys@vcc3v3_sys: set 3300000 uV; enabling (ret: -38) vcc-phy-regulator@vcc_phy: ; enabling (ret: -38) vdd-log@vdd_log: ; enabling (ret: -38) MMC: sdhci@fe330000: 0, dwmmc@fe320000: 1 SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial@ff1a0000 Out: serial@ff1a0000 Err: serial@ff1a0000 Model: Pine64 RockPro64 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 ** First descriptor is NOT a primary desc on 0:1 ** switch to partitions #0, OK mmc0(part 0) is current device ** First descriptor is NOT a primary desc on 0:1 ** ** First descriptor is NOT a primary desc on 0:1 ** ** First descriptor is NOT a primary desc on 0:1 ** ** First descriptor is NOT a primary desc on 0:1 ** : ** First descriptor is NOT a primary desc on 0:1 ** ** First descriptor is NOT a primary desc on 0:1 ** ** No partition table - mmc 0 ** switch to partitions #0, OK mmc1 is current device Scanning mmc 1:1... Found EFI removable media binary efi/boot/bootaa64.efi reading efi/boot/bootaa64.efi 161090 bytes read in 26 ms (5.9 MiB/s) libfdt fdt_check_header(): FDT_ERR_BADMAGIC ## Starting EFI application at 02000000 ... Scanning disk sd...@fe330000.blk... ** First descriptor is NOT a primary desc on 0:1 ** Scanning disk dw...@fe320000.blk... Found 2 disks disks: sd0* sd1 sd2 >> OpenBSD/arm64 BOOTAA64 0.19 boot> cannot open sd0a:/etc/random.seed: No such file or directory booting sd0a:/bsd: 2231112+623664+8769760+740912 [221760+109+520368+200924]=0xff8710 type 0x2 pa 0x200000 va 0x200000 pages 0x4000 attr 0x8 type 0x7 pa 0x4200000 va 0x200000 pages 0x4000 attr 0x8 type 0x4 pa 0x8200000 va 0x8200000 pages 0xc attr 0x8 type 0x7 pa 0x820d000 va 0x200000 pages 0xebf8b attr 0x8 type 0x2 pa 0xf4198000 va 0xf4198000 pages 0x4 attr 0x8 type 0x2 pa 0xf419c000 va 0xf419c000 pages 0x4 attr 0x8 : "vcc-phy-regulator" at mainbus0 not configured "vdd-log" at mainbus0 not configured usb2 at ohci0: USB revision 1.0 uhub2 at usb2 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 usb3 at ohci1: USB revision 1.0 uhub3 at usb3 configuration 1 interface 0 "Generic OHCI root hub" rev 1.00/1.00 addr 1 scsibus0 at sdmmc1: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <SD/MMC, USD, 0000> removable sd0: 3840MB, 512 bytes/sector, 7864320 sectors scsibus1 at sdmmc0: 2 targets, initiator 0 sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4128, 0000> removable sd1: 119276MB, 512 bytes/sector, 244277248 sectors softraid0 at root scsibus2 at softraid0: 256 targets bootfile: sd0a:/bsd boot device: sd0 root on rd0a swap on rd0b dump on rd0b WARNING: preposterous clock chip time WARNING: CHECK AND RESET THE DATE! erase ^?, werase ^W, kill ^U, intr ^C, status ^T Welcome to the OpenBSD/arm64 6.6 installation program. (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s # cd /dev # sh MAKEDEV sd0 # sh MAKEDEV sd1 # sh MAKEDEV sd2 # fdisk sd0 Disk: sd0 geometry: 489/255/63 [7864320 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- *0: 0C 2 10 9 - 2 140 10 [ 32768: 8192 ] FAT32L 1: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused 2: 00 0 0 0 - 0 0 0 [ 0: 0 ] unused 3: A6 2 140 11 - 4 52 48 [ 40960: 26624 ] OpenBSD # fdisk sd1 Disk: sd1 geometry: 15205/255/63 [244277248 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT # fdisk -i sd1 Do you wish to write new MBR and partition table? [n] y Writing MBR at offset 0. # fdisk sd1 Disk: sd1 geometry: 15205/255/63 [244277248 Sectors] Offset: 0 Signature: 0xAA55 Starting Ending LBA Info: #: id C H S - C H S [ start: size ] ------------------------------------------------------------------------------- 0: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 1: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 2: FF 267349 89 4 - 267349 89 2 [ 4294967295: 4294967295 ] Xenix BBT 3: FF 267349 89 4 - 46077 37 38 [ 4294967295: 740229375 ] Xenix BBT # disklabel sd1 # /dev/rsd1c: type: SCSI disk: SCSI disk label: Sandisk DA4128 duid: 0000000000000000 flags: bytes/sector: 512 sectors/track: 63 tracks/cylinder: 255 sectors/cylinder: 16065 cylinders: 15205 total sectors: 244277248 boundstart: 0 boundend: 244277248 drivedata: 0 16 partitions: # size offset fstype [fsize bsize cpg] c: 244277248 0 unused # fdisk sd2 fdisk: sd2: Device not configured # sysctl kern.osrelease=6.6 hw.machine=arm64 hw.model=ARM Cortex-A53 r0p4 hw.product=Pine64 RockPro64 hw.disknames=rd0:065c1213d288d6ad,sd0:02c868c8a1ad48b6,sd1: hw.ncpufound=6 # disklabel rd0 # /dev/rrd0c: type: rdroot disk: rdroot label: duid: 065c1213d288d6ad flags: bytes/sector: 512 sectors/track: 512 tracks/cylinder: 2 sectors/cylinder: 1024 cylinders: 16 total sectors: 16384 boundstart: 0 boundend: 0 drivedata: 0 3 partitions: # size offset fstype [fsize bsize cpg] a: 16384 0 4.2BSD 512 4096 2048 c: 16384 0 unused # disklabel sd0 # /dev/rsd0c: type: vnd disk: vnd device label: fictitious duid: 02c868c8a1ad48b6 flags: bytes/sector: 512 sectors/track: 128 tracks/cylinder: 16 sectors/cylinder: 2048 cylinders: 33 total sectors: 7864320 boundstart: 40960 boundend: 67584 drivedata: 0 16 partitions: # size offset fstype [fsize bsize cpg] a: 26624 40960 4.2BSD 2048 16384 832 c: 7864320 0 unused i: 8192 32768 MSDOS commands from U-boot => usb start starting USB... USB0: USB EHCI 1.00 USB1: USB EHCI 1.00 USB2: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 USB3: Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning bus 2 for devices... 1 USB Device(s) found scanning bus 3 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found => mmc info ** First descriptor is NOT a primary desc on 0:1 ** Device: sdhci@fe330000 Manufacturer ID: 45 OEM: 100 Name: DA412 Tran Speed: 52000000 Rd Block Len: 512 MMC version 5.1 High Capacity: Yes Capacity: 116.5 GiB Bus Width: 8-bit Erase Group Size: 512 KiB HC WP Group Size: 8 MiB User Capacity: 116.5 GiB WRREL Boot Capacity: 4 MiB ENH RPMB Capacity: 16 MiB ENH => mmc list sdhci@fe330000: 0 (eMMC) dwmmc@fe320000: 1 => led list power <inactive> standby <inactive> => led list power <inactive> standby <inactive> => led standby off => mmcinfo Device: sdhci@fe330000 Manufacturer ID: 45 OEM: 100 Name: DA412 Tran Speed: 52000000 Rd Block Len: 512 MMC version 5.1 High Capacity: Yes Capacity: 116.5 GiB Bus Width: 8-bit Erase Group Size: 512 KiB HC WP Group Size: 8 MiB User Capacity: 116.5 GiB WRREL Boot Capacity: 4 MiB ENH RPMB Capacity: 16 MiB ENH => printenv arch=arm baudrate=1500000 board=rockpro64_rk3399 board_name=rockpro64_rk3399 boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} boot_efi_binary=load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} efi/boot/bootaa64.efi; if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r};else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf boot_net_usb_start=usb start boot_prefixes=/ /boot/ boot_script_dhcp=boot.scr.uimg boot_scripts=boot.scr.uimg boot.scr boot_targets=mmc0 mmc1 usb0 pxe dhcp bootcmd=run distro_bootcmd bootcmd_dhcp=run boot_net_usb_start; if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi;setenv efi_fdtfile ${fdtfile}; setenv efi_old_vci ${bootp_vci};setenv efi_old_arch ${bootp_arch};setenv bootp_vci PXEClient:Arch:00011:UNDI:003000;setenv bootp_arch 0xb;if dhcp ${kernel_addr_r}; then tftpboot ${fdt_addr_r} dtb/${efi_fdtfile};if fdt addr ${fdt_addr_r}; then bootefi ${kernel_addr_r} ${fdt_addr_r}; else bootefi ${kernel_addr_r} ${fdtcontroladdr};fi;fi;setenv bootp_vci ${efi_old_vci};setenv bootp_arch ${efi_old_arch};setenv efi_fdtfile;setenv efi_old_arch;setenv efi_old_vci; bootcmd_mmc0=setenv devnum 0; run mmc_boot bootcmd_mmc1=setenv devnum 1; run mmc_boot bootcmd_pxe=run boot_net_usb_start; dhcp; if pxe get; then pxe boot; fi bootcmd_usb0=setenv devnum 0; run usb_boot bootdelay=0 cpu=armv8 cpuid#=5456413830342e303000000000180482 distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done efi_dtb_prefixes=/ /dtb/ /dtb/current/ ethaddr=a6:63:b8:9a:57:7c fdt_addr_r=0x01f00000 fdtcontroladdr=f5f04348 fdtfile=rockchip/rk3399-rockpro64.dtb kernel_addr_r=0x02000000 load_efi_dtb=load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} ${prefix}${efi_fdtfile} mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi partitions=uuid_disk=${uuid_gpt_disk};name=loader1,start=32K,size=4000K,uuid=${uuid_gpt_loader1};name=loader2,start=8MB,size=4MB,uuid=${uuid_gpt_loader2};name=trust,size=4M,uuid=${uuid_gpt_atf};name=boot,size=112M,bootable,uuid=${uuid_gpt_boot};name=rootfs,size=-,uuid=B921B045-1DF0-41C3-AF44-4C6F280D3FAE; pxefile_addr_r=0x00600000 ramdisk_addr_r=0x04000000 scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done;run scan_dev_for_efi; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done scan_dev_for_efi=setenv efi_fdtfile ${fdtfile}; for prefix in ${efi_dtb_prefixes}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${efi_fdtfile}; then run load_efi_dtb; fi;done;if test -e ${devtype} ${devnum}:${distro_bootpart} efi/boot/bootaa64.efi; then echo Found EFI removable media binary efi/boot/bootaa64.efi; run boot_efi_binary; echo EFI LOAD FAILED: continuing...; fi; setenv efi_fdtfile scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scriptaddr=0x00500000 serial#=efe22a02b7a2961 soc=rockchip stderr=serial@ff1a0000 stdin=serial@ff1a0000 stdout=serial@ff1a0000 usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi vendor=rockchip Environment size: 4013/32764 bytes => mmc list sdhci@fe330000: 0 (eMMC) dwmmc@fe320000: 1 => sdhci@fe330000: 0 (eMMC) dwmmc@fe320000: 1 => mmc rescan ** First descriptor is NOT a primary desc on 0:1 ** => mmc list sdhci@fe330000: 0 (eMMC) dwmmc@fe320000: 1 => usb storage No storage devices, perhaps not 'usb start'ed..? => usb start => usb storage No storage devices, perhaps not 'usb start'ed..? => version U-Boot 2017.09-rockchip-ayufan-1065-g95f6152134 (Aug 26 2019 - 12:41:34 +0000) aarch64-linux-gnu-gcc (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1) 7.4.0 GNU ld (GNU Binutils for Ubuntu) 2.30 once again with snapshot # disklabel -E sd1 Label editor (enter '?' for help at any prompt) sd1> a partition: [a] offset: [0] size: [244277248] FS type: [4.2BSD] sd1*> w disklabel: DIOCWDINFO: Input/output error disklabel: unable to write label
smime.p7s
Description: S/MIME cryptographic signature
