See the answer I got. -current is not for general consumption, it's a work in progress. I tried it once years ago then had to replace it all later, since then I don't bother with it. If you're not part of the R&D effort it's probably not worth it.
I used the time to write an epidemic simulation program. On 3/19/20, Marcus MERIGHI <mcmer-open...@tor.at> wrote: > Hello! > > Just got my Pinebook Pro. What a beauty! > And I am forced to stay at home because of SARS-COV-II/COVID-19. > > This lucky coincidence is dulled by my incapability to install OpenBSD > on the Pinebook Pro. > > I've tried everything I could find, from: > https://ftp.openbsd.org/pub/OpenBSD/snapshots/arm64/INSTALL.arm64 > "Install on systems without a supported miniroot:" > > ... to various hints on forums.pine64.org, which mostly relate to the > pinebook (w/o "pro"). > > Initially OpenBSD -current install ran ok until the point where the > firmware for the bwfm(4) wifi was not found. > > I then used the upgrade script that comes with the original OS. > > Afterwards I only ever got to the boot> prompt where it never finds > anything to boot/install from. > > I have the output from serial saved, see below. > > Has anyone got a hint for me? > > Thanks, Marcus > > $ cu -s 1500000 -l /dev/cuaU0 -d > -- > boot from sdcard > -- > Connected to /dev/cuaU0 (speed 1500000) > > DDR Version 1.20 20190314 > > In > > channel 0 > > CS = 0 > > MR0=0x98 > > MR4=0x3 > > MR5=0xFF > > MR8=0x8 > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > CS = 1 > > MR0=0x18 > > MR4=0x3 > > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > channel 1 > > CS = 0 > > MR0=0x98 > > MR4=0x3 > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > CS = 1 > > MR0=0x18 > > MR4=0x1 > > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > channel 0 training pass! > > channel 1 training pass! > change freq to 400MHz 0,1 > > channel 0 > > CS = 0 > > MR0=0x98 > > MR4=0x81 > > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > CS = 1 > > MR0=0x18 > > MR4=0x81 > > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > channel 1 > > CS = 0 > > MR0=0x98 > > MR4=0x81 > > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > > MR14=0x72 > > MR18=0x0 > > M0 > > MR24=0x8 > > MR25=0x0 > > CS = 1 > > MR0=0x18 > > MR4=0x1 > > MR5=0xFF > > MR8=0x8 > > MR12=0x72 > MR14=0x72 > > MR18=0x0 > > MR19=0x0 > > MR24=0x8 > > MR25=0x0 > > channel 0 training pass! > > channel 1 training pass! > > change freq to 800MHz 1,0 > > Channel 0: LPDDR4,800MHz > > Bus Width=32 Col=10 nk=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB > > Channel 1: LPDDR4,800MHz > > Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB > > 256B stride > > ch 0 ddrconfig = 0x101, ddrsize = 0x2020 > > ch 1 ddrconfig = 0x101, ddrsize = 0x2020 > > pmugrf_os_r= 0x3AA1FAA1, stride = 0xD > > OUT > > Boot1: 2019-03-14, version: 1.19 > > CPUId = 0x0 > > ChipType = 0x10, 250 > > SdmmcInit=2 0 > BootCapSize=100000 > > UserCapSize=59640MB > > FwPartOffset=2000 , 100000 > > mmc0:cmd5,20 > > mmc0:cmd7,10 > > mmc0:cmd5,20 > > mmc0:cmd7,10 > > mmc0:cmd5,20 > > mmc0:cmd7,10 > > SdmmcInit=0 1 > > StorageInit ok = 355218 > > SecureMode = 0 > > SecureInit read PBA: 0x4 > > SecureInit read PBA: 0x404 > > SecureInit read PBA: 0x804 > > SecureInit read PBA: 0xc04 > > SecureInit read PBA: 0x1004 > > SecureInit read PBA: 0x1404 > > SecureInit read PBA: 0x1804 > > SecureInit read PBA: 0x1c04 > > SecureInit ret = 0, SecuMode = 0 > atags_set_bootdev: ret:(0) > > GPT 0x3380ec0 signature is wrong > > recovery gpt... > > GPT 0x3380ec0 signature is wrong > > recovery gpt fail! > > LoadTrust Addr:0x4000 > > No find bl30.bin > > No find bl32.bin > > Load uboot, ReadLba = 2000 > > Load OK, addr=0x200000, size=0xe5970 > > RunBL31 0x10000 > > NOTICE: BL31: v1.3(debug):22b599a > > NOTICE: BL31: Built : 11:03:32, Jul 10 2019 > > NOTICE: BL31: Rockchip release version: v1.1 > > INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in > EL3 > INFO: Using opteed sec cpu_context! > > INFO: boot cpu mask: 0 > > INFO: plat_rockchip_pmu_init(1181): pd status 3e > > INFO: BL31: Initializing runtime services > > WARNING: No OPTEE provideting device without OPTEE initialization. SMC`s > destine > d for OPTEE will return SMC_UNK > ERROR: Error initializing runtime service opteed_fast > > INFO: BL31: Preparing for EL3 exit to normal world > > INFO: Entry point address = 0x200000 > > INFO: SPSR =fdtdec_get_addr_size_fixed: reg: addr=ff770000, size=10000 > > fdtdec_get_addr_size_fixed: reg: addr=ff320000, size=1000 > > > > U-Boot 2017.09-04112-gb8e0774-dirty (Feb 07 2020 - 12:45:13 -0500) > > > Model: Pine64 RK3399 Pinebook Pro > > PreSerial: 2 > > DRAM: 3.9 GiB > > Sysmem: init > > Relocation Offset: f5be7000, fdt: f3dd2238 > > I2c0 speed: 400000Hz > > PMIC: RK808 > > vdd_center 900000 uV > > vdd_log init 900000 uV > > rk_board_init PWM2 pinctrl init fail! > > rk_board_init: vcc3v0_sdio cannot set regulator value -38 > > vdd_center 900000 uV > DCDC_REG1@ vdd_center: 750000uV <-> 1400000uV, set > 900000u > V, enabling | suspend -61uV, disabled > > DCDC_REG4@ vcc_1v8: 1800000uV 00uV, set 1800000uV, > enabli > ng | suspend 1800000uV, enabling > > LDO_REG1@ vcc1v8_dvp: 1800000uV <-> 1800000uV, set > 1800000u > V, enabling | suspend 1800000uV, enabling > > LDO_REG4@ vcc_sd: 3300000uV <-> 3300000uV, set nd > 33000 > 00uV, enabling > > LDO_REG5@ vcca3v0_codec: 3000000uV <-> 3000000uV, set > 3000000u > V, enabling | suspend 3000000uV, enabling > > LDO_REG7@ vcca1v8_codec: 1800000uV <-> 1800000uV, set > 1800000u > V, enabling | suspend 18000008@ vcc_3v0: 3000000uV <-> 3000000uV, set > 300 > 0000uV, enabling | suspend 3000000uV, enabling > > SWITCH_REG2@ vcc3v3_s0: -61uV <-> -61uV, set > 0u > V, enabling | suspend -61uV, disabled > > dc-12v@ -38) > > vcc3v3-sys@ vcc3v3_sys: 3300000uV <-> 3300000uV, set > 3300000u > V, enabling | suspend -61uV, enabling (ret: -38) > > vcc-phy-regulator@ vcc_phy: -61uV <-> -61uV, set > -61u > V, enabling | suspend -61uV, enauV <-> -61uV, set -61uV, > enabling | > suspend -61uV, enabling > vcc5v0-host-en@ vcc5v0_host: 5000000uV <-> 5000000uV, set > 5000000u > V, enabling | suspend -61uV, enabling (ret: -38) > > vcc5v0-usb3-host-regulator@vcc5v0_usb3_host: 1uV, enabling | suspend > -61 > uV, enabling > > vcc5v0-typec0-en@ vcc5v0_typec0: -61uV <-> -61uV, set > -61u > V, enabling | suspend -61uV, enabling > > vcc3v3-pcie-regulator@ vcc3v3_pcie: 3300000uV <-> 3300000uV, set > 3300000u > V, disabnabling > > vcc1v8-sdio@ vcc1v8_sdio: 1800000uV <-> 1800000uV, set > 1800000u > V, enabling | suspend -61uV, enabling (ret: -38) > > vcc3v0-sdio@ vcc3v0_sdio: 3000000uV <-> 3000000uV, set > 3000000u > V, enabling | suspend -61uV, 8) > > vdd_log init 900000 uV > > vdd_log@ vdd_log: 800000uV <-> 1400000uV, set > 900000u > V, enabling | suspend -61uV, enabling ; init 900000uV > > MMC: dwmmc@fe310000: 2, sdhci@fe330000: 0, dwmmc@fe320000: 1 > > Invalid bus 0 (err=-19) > > *** Warning - spi_flash_probe_bus_cs() failed, using default environment > > > In: serial > > Out: serial > Err: serial > > Model: Pine64 RK3399 Pinebook Pro > > RKPARM: Invalid parameter part table > > Bootdev(atags): mmc 0 > > PartType: DOS > > rockchip_get_boot_mode: Could not found misc partition > > boot mode: None > > init_resource_list: failed to get resource part, ret=-1 > > Can't find file:logo.bmp > > failed to display uboot logo > > CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A) > > CLK: (uboot. armb: enter 816000 KHz, init 816000 KHz, kernel 0N/A) > > aplll 816000 KHz > > apllb 816000 KHz > > dpll 800000 KHz > > cpll 24000z > > vpll 24000 KHz > > aclk_perihp 133333 KHz > > hclk_perihp 66666 KHz > > pclk_perihp 33333 KHz > > aclk_perilp0 266666 KHz > hclk_perilp0 88888 KHz > > pclk_perilp0 44444 KHz > > hclk_perilp1 100000 KHz > > pclk_perilp1 50000 KHz > > Net: No ethernet found. > > Hit key to stop autoboot('CTRL+C'): 0 > > do_boot_rockchip: Could not find mmcsda2 part > > Checking for mmc dev 1... > > RKPARM: Invalid parameter part table > > switch to partitions #0, OK > > mmc1 is current device > > Scanning mmc 1 for bootable partitions... > > Scanning mmc 1:1 for extlinux or boot scripts... > > Found EFI removable media binary efi/boot/bootaa64.efi > > reading efi/boot/bootaa64.efi > > 168758 bytes read in 14 ms (11.5 MiB/s) > > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > > ## Starting EFI application at 00280000 ... > > Card did not respond to voltage select! > > mmc_init: -95, time 50 > > Scanning disk dw...@fe310000.blk... > MMC: block number 0x1 exceeds max(0x0) > > MMC: block number 0x2080 exceeds max(0x0) > > rkparm_init_param_from_storage param read fail > > RKPARM: Invalid parameter part table > > MMC: block number 0x1 exceeds max(0x0) > > MMC: blocnning disk sd...@fe330000.blk... > > Scanning disk dw...@fe320000.blk... > > Found 3 disks > > Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000) > > disks: sd0 sd1 sd2 sd3 sd4 > >>> OpenBSD/arm64 BOOTAA64 0.20 >>> > open(tftp0a:/etc/boot.conf): Operation not permitted > > boot> set device hd0a > boot> ls > stat(hd0a:/.): Device not configured > > -- > boot from usb3: > > Checking for mmc dev 1... > > Card did not respond to voltage select! > > mmc_init: -95, time 9 > > Checking for nvme dev 0... > > > Device 0: unknown device > > starting USB... > Bus usb@fe380000: USB EHCI 1.00 > > Bus usb@fe3a0000: USB OHCI 1.0 > > Bus usb@fe3c0000: USB EHCI 1.00 > > Bus usb@fe3e0000: USB OHCI 1.0 > > Bus usb@fe800000: device name usb@fe800000 > > Register 2000140 NbrPorts 2 > > Starting the controller > > USB XHCI 1.10 > > Bus usb@fe900000: device name usb@fe900000 > > Register 2000140 NbrPorts 2 > > Starting the controller > > USB XHCI 1.10 > scanning bus usb@fe380000 for devices... 1 USB Device(s) found > > scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found > > scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found > > scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found > > scanning bus usb@fe800000 for devices... 1 USB Device(s) found > > scanning bus usb@fe900000 for devices... RKPARM: Invalid parameter part > table > 2 USB Device(s) found > > scanning usb for storage devices... 1 Storage Device(s) found > > Checking for usb dev 0... > > Device 0: Vendor: SanDisk Rev: 0001 Prod: Extreme > > Type: Hard Disk > > Capacity: 15272.0 MB = 14.9 GB (31277232 x 512) > > ... is now current device > > Scanning usb 0 for bScanning usb 0:1 for extlinux or boot scripts... > > Found EFI removable media binary efi/boot/bootaa64.efi > > reading efi/boot/bootaa64.efi > > 168758 bytes read in 69 ms (2.3 MiB/s) > > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > > ## Starting EFI application at 00280000 ... > > Card did not respond to voltage select! > mmc_init: -95, time 50 > > Scanning disk dw...@fe310000.blk... > > MMC: block number 0x1 exceeds max(0x0) > > MMC: block number 0x2080 exceeds max(0x0) > > rkparm_init_param_from_storage param read fail > > RKPARM: Invalid parameter part table > > MMC: block number 0x1 exceeds max(0x0) > > MMC: blocScanning disk sd...@fe330000.blk... > > Card did not respond to voltage select! > mmc_init: -95, time 9 > > Scanning disk dw...@fe320000.blk... > > MMC: block number 0x1 exceeds max(0x0) > > MMC: block number 0x2080 exceeds max(0x0) > > rkparm_init_param_from_storage param read fail > > RKPARM: Invalid parameter part table > > MMC: block number 0x1 exceeds max(0x0) > > MMC: blockanning disk usb_mass_storage.lun0... > > Found 4 disks > > Adding bank: 0x00200000 - 0xf8000000 (size: 0xf7e00000) > > disks: sd0 sd1 sd2 sd3 sd4 > >>> OpenBSD/arm64 BOOTAA64 0.20 > open(tftp0a:/etc/boot.conf): Operation not permitted > > boot> > > alan01...@gmail.com (Alan Corey), 2020.03.18 (Wed) 14:38 (CET): >> OK, thanks, I'll just leave room for it on my SSD and try 6.7 when it >> comes out. I'm not in any rush for it. >> >> On 3/18/20, Otto Moerbeek <o...@drijf.net> wrote: >> > On Wed, Mar 18, 2020 at 02:08:07PM +0100, Mark Kettenis wrote: >> > >> >> You'll need -current on this hardware. >> > >> > To elaborate a bit: several developers have one and good progress has >> > been made. You'll need a very recent snap though and I'm not sure if >> > the wifi firmware package needed has been updated already. To be able >> > to boot from NVMe you'll need an updated u-boot. But e.g. X works >> > already. >> > >> > -Otto >> > >> > OpenBSD 6.6-current (GENERIC.MP) #29: Tue Mar 17 09:39:57 CET 2020 >> > o...@pbp.intra.drijf.net:/usr/src/sys/arch/arm64/compile/GENERIC.MP >> > real mem = 4027723776 (3841MB) >> > avail mem = 3831341056 (3653MB) >> > mainbus0 at root: Pine64 Pinebook Pro >> > cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 >> > cpu0: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 >> > D-cache >> > cpu0: 512KB 64b/line 16-way L2 cache >> > efi0 at mainbus0: UEFI 2.0.5 >> > efi0: Das U-boot rev 0x0 >> > apm0 at mainbus0 >> > psci0 at mainbus0: PSCI 1.0 >> > agintc0 at mainbus0 sec shift 3:4 nirq 288 nredist 6 ipi: 0, 1: >> > "interrupt-controller" >> > agintcmsi0 at agintc0 >> > syscon0 at mainbus0: "qos" >> > syscon1 at mainbus0: "qos" >> > syscon2 at mainbus0: "qos" >> > syscon3 at mainbus0: "qos" >> > syscon4 at mainbus0: "qos" >> > syscon5 at mainbus0: "qos" >> > syscon6 at mainbus0: "qos" >> > syscon7 at mainbus0: "qos" >> > syscon8 at mainbus0: "qos" >> > syscon9 at mainbus0: "qos" >> > syscon10 at mainbus0: "qos" >> > syscon11 at mainbus0: "qos" >> > syscon12 at mainbus0: "qos" >> > syscon13 at mainbus0: "qos" >> > syscon14 at mainbus0: "qos" >> > syscon15 at mainbus0: "qos" >> > syscon16 at mainbus0: "qos" >> > syscon17 at mainbus0: "qos" >> > syscon18 at mainbus0: "qos" >> > syscon19 at mainbus0: "qos" >> > syscon20 at mainbus0: "qos" >> > syscon21 at mainbus0: "qos" >> > syscon22 at mainbus0: "qos" >> > syscon23 at mainbus0: "qos" >> > syscon24 at mainbus0: "qos" >> > syscon25 at mainbus0: "power-management" >> > "power-controller" at syscon25 not configured >> > syscon26 at mainbus0: "syscon" >> > "io-domains" at syscon26 not configured >> > rkclock0 at mainbus0 >> > rkclock1 at mainbus0 >> > syscon27 at mainbus0: "syscon" >> > "io-domains" at syscon27 not configured >> > "usb2-phy" at syscon27 not configured >> > "usb2-phy" at syscon27 not configured >> > rkemmcphy0 at syscon27 >> > "pcie-phy" at syscon27 not configured >> > rkpinctrl0 at mainbus0: "pinctrl" >> > rkgpio0 at rkpinctrl0 >> > rkgpio1 at rkpinctrl0 >> > rkgpio2 at rkpinctrl0 >> > rkgpio3 at rkpinctrl0 >> > rkgpio4 at rkpinctrl0 >> > pwmreg0 at mainbus0 >> > rkdrm0 at mainbus0 >> > drm0 at rkdrm0 >> > "pmu_a53" at mainbus0 not configured >> > "pmu_a72" at mainbus0 not configured >> > agtimer0 at mainbus0: tick rate 24000 KHz >> > "xin24m" at mainbus0 not configured >> > simplebus0 at mainbus0: "amba" >> > "dma-controller" at simplebus0 not configured >> > "dma-controller" at simplebus0 not configured >> > rkpcie0 at mainbus0 >> > pci0 at rkpcie0 >> > ppb0 at pci0 dev 0 function 0 "Rockchip RK3399 Root Complex" rev 0x00: >> > msi >> > pci1 at ppb0 bus 1 >> > nvme0 at pci1 dev 0 function 0 vendor "Intel", unknown product 0xf1a8 >> > rev >> > 0x03: msix, NVMe 1.3 >> > nvme0: INTEL SSDPEKNW512G8, firmware 002C, serial BTNH907209AN512A >> > scsibus0 at nvme0: 2 targets, initiator 0 >> > sd0 at scsibus0 targ 1 lun 0: <NVMe, INTEL SSDPEKNW51, 002C> >> > sd0: 488386MB, 512 bytes/sector, 1000215216 sectors >> > dwmmc0 at mainbus0: 50 MHz base clock >> > sdmmc0 at dwmmc0: 4-bit, sd high-speed, dma >> > dwmmc1 at mainbus0: 50 MHz base clock >> > sdmmc1 at dwmmc1: 4-bit, sd high-speed, mmc high-speed, dma >> > sdhc0 at mainbus0 >> > sdhc0: SDHC 3.0, 18 MHz base clock >> > sdmmc2 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma >> > ehci0 at mainbus0 >> > usb0 at ehci0: USB revision 2.0 >> > uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev >> > 2.00/1.00 addr 1 >> > ohci0 at mainbus0: version 1.0 >> > ehci1 at mainbus0 >> > usb1 at ehci1: USB revision 2.0 >> > uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev >> > 2.00/1.00 addr 1 >> > ohci1 at mainbus0: version 1.0 >> > rkdwusb0 at mainbus0: "usb" >> > xhci0 at rkdwusb0, xHCI 1.10 >> > usb2 at xhci0: USB revision 3.0 >> > uhub2 at usb2 configuration 1 interface 0 "Generic xHCI root hub" rev >> > 3.00/1.00 addr 1 >> > rkdwusb1 at mainbus0: "usb" >> > xhci1 at rkdwusb1, xHCI 1.10 >> > usb3 at xhci1: USB revision 3.0 >> > uhub3 at usb3 configuration 1 interface 0 "Generic xHCI root hub" rev >> > 3.00/1.00 addr 1 >> > "dp" at mainbus0 not configured >> > "saradc" at mainbus0 not configured >> > rkiic0 at mainbus0 >> > iic0 at rkiic0 >> > "everest,es8316" at iic0 addr 0x11 not configured >> > rkiic1 at mainbus0 >> > iic1 at rkiic1 >> > com0 at mainbus0: ns16550, no working fifo >> > com1 at mainbus0: ns16550, no working fifo >> > com1: console >> > "spi" at mainbus0 not configured >> > "thermal-zones" at mainbus0 not configured >> > rktemp0 at mainbus0 >> > rkiic2 at mainbus0 >> > iic2 at rkiic2 >> > rkpmic0 at iic2 addr 0x1b: RK808 >> > fanpwr0 at iic2 addr 0x40: SYR827, 1.00 VDC >> > fanpwr1 at iic2 addr 0x41: SYR828, 1.00 VDC >> > rkiic3 at mainbus0 >> > iic3 at rkiic3 >> > fusbtc0 at iic3 addr 0x22 >> > "cellwise,cw201x" at iic3 addr 0x62 not configured >> > rkpwm0 at mainbus0 >> > rkpwm1 at mainbus0 >> > "video-codec" at mainbus0 not configured >> > "iommu" at mainbus0 not configured >> > "rga" at mainbus0 not configured >> > "efuse" at mainbus0 not configured >> > "phy" at mainbus0 not configured >> > "phy" at mainbus0 not configured >> > "watchdog" at mainbus0 not configured >> > "rktimer" at mainbus0 not configured >> > "i2s" at mainbus0 not configured >> > rkvop0 at mainbus0: RK3399 VOPL >> > "iommu" at mainbus0 not configured >> > rkvop1 at mainbus0: RK3399 VOPB >> > "iommu" at mainbus0 not configured >> > "iommu" at mainbus0 not configured >> > "iommu" at mainbus0 not configured >> > "hdmi-sound" at mainbus0 not configured >> > rkanxdp0 at mainbus0: eDP TX >> > "gpu" at mainbus0 not configured >> > "opp-table0" at mainbus0 not configured >> > "opp-table1" at mainbus0 not configured >> > "opp-table2" at mainbus0 not configured >> > simplepanel0 at mainbus0 >> > "leds" at mainbus0 not configured >> > "reserved-memory" at mainbus0 not configured >> > "gpio-keys" at mainbus0 not configured >> > pwmbl0 at mainbus0 >> > "sdio-pwrseq" at mainbus0 not configured >> > "wireless-wlan" at mainbus0 not configured >> > "es8316-sound" at mainbus0 not configured >> > "speaker-amplifier" at mainbus0 not configured >> > "vcc-sysin" at mainbus0 not configured >> > "vcc-12v" at mainbus0 not configured >> > "vcc3v3-sys" at mainbus0 not configured >> > "vcc5v0-usb-regulator" at mainbus0 not configured >> > "vcc-0v9" at mainbus0 not configured >> > "vcc1v8-s3" at mainbus0 not configured >> > "vcc3v0-sd" at mainbus0 not configured >> > "vcc3v3-panel" at mainbus0 not configured >> > "vcc3v3-ssd" at mainbus0 not configured >> > "vcc5v0-otg" at mainbus0 not configured >> > "vbus-5vout" at mainbus0 not configured >> > "dc-charger" at mainbus0 not configured >> > "usb-charger" at mainbus0 not configured >> > "framebuffer" at mainbus0 not configured >> > cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4 >> > cpu1: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 >> > D-cache >> > cpu1: 512KB 64b/line 16-way L2 cache >> > cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4 >> > cpu2: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 >> > D-cache >> > cpu2: 512KB 64b/line 16-way L2 cache >> > cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4 >> > cpu3: 32KB 64b/line 2-way L1 VIPT I-cache, 32KB 64b/line 4-way L1 >> > D-cache >> > cpu3: 512KB 64b/line 16-way L2 cache >> > cpu4 at mainbus0 mpidr 100: ARM Cortex-A72 r0p2 >> > cpu4: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 >> > D-cache >> > cpu4: 1024KB 64b/line 16-way L2 cache >> > cpu5 at mainbus0 mpidr 101: ARM Cortex-A72 r0p2 >> > cpu5: 48KB 64b/line 3-way L1 PIPT I-cache, 32KB 64b/line 2-way L1 >> > D-cache >> > cpu5: 1024KB 64b/line 16-way L2 cache >> > usb4 at ohci0: USB revision 1.0 >> > uhub4 at usb4 configuration 1 interface 0 "Generic OHCI root hub" rev >> > 1.00/1.00 addr 1 >> > usb5 at ohci1: USB revision 1.0 >> > uhub5 at usb5 configuration 1 interface 0 "Generic OHCI root hub" rev >> > 1.00/1.00 addr 1 >> > bwfm0 at sdmmc0 function 1 >> > manufacturer 0x02d0, product 0xa9bf at sdmmc0 function 2 not configured >> > manufacturer 0x02d0, product 0xa9bf at sdmmc0 function 3 not configured >> > scsibus1 at sdmmc2: 2 targets, initiator 0 >> > sd1 at scsibus1 targ 1 lun 0: <Sandisk, DA4064, 0000> removable >> > sd1: 59640MB, 512 bytes/sector, 122142720 sectors >> > uhub6 at uhub1 port 1 configuration 1 interface 0 "Genesys Logic USB2.0 >> > Hub" >> > rev 2.00/85.36 addr 2 >> > uvideo0 at uhub6 port 2 configuration 1 interface 0 "Sonix Technology >> > Co., >> > Ltd. USB Camera" rev 2.00/0.00 addr 3 >> > video0 at uvideo0 >> > uhidev0 at uhub4 port 1 configuration 1 interface 0 "HAILUCK CO.,LTD >> > USB >> > KEYBOARD" rev 1.10/1.00 addr 2 >> > uhidev0: iclass 3/1 >> > ukbd0 at uhidev0: 8 variable keys, 6 key codes >> > wskbd0 at ukbd0 mux 1 >> > uhidev1 at uhub4 port 1 configuration 1 interface 1 "HAILUCK CO.,LTD >> > USB >> > KEYBOARD" rev 1.10/1.00 addr 2 >> > uhidev1: iclass 3/0, 35 report ids >> > umt0 at uhidev1: clickpad, 4 contacts >> > wsmouse0 at umt0 mux 0 >> > vscsi0 at root >> > scsibus2 at vscsi0: 256 targets >> > softraid0 at root >> > scsibus3 at softraid0: 256 targets >> > bootfile: sd0a:/bsd >> > boot device: sd0 >> > root on sd0a (affd0af770a51ab1.a) swap on sd0b dump on sd0b >> > rkvop0: using CRTC 0 for RK3399 VOPL >> > rkvop1: using CRTC 1 for RK3399 VOPB >> > rkdrm0: 1920x1080, 32bpp >> > wsdisplay0 at rkdrm0 mux 1 >> > wskbd0: connecting to wsdisplay0 >> > wsdisplay0: screen 0-5 added (std, vt100 emulation) >> > bwfm0: address c0:84:7d:25:a1:f2 > > -- ------------- No, I won't call it "climate change", do you have a "reality problem"? - AB1JX Cities are cages built to contain excess people and keep them from cluttering up nature. Impeach Impeach Impeach Impeach Impeach Impeach Impeach Impeach
