Hi, yes, I see this consistently, it actually falls into a reboot loop (U-Boot ==> starting the install kernel ==> panic ==> U-Boot and the cycle goes on). My board is Pandaboard Rev A2.
BR Marcus Am 26.08.2018 um 06:12 schrieb Jonathan Gray: > On Sat, Aug 25, 2018 at 08:56:37AM +0200, Marcus Lindemann wrote: >> Hi, >> I'm trying to install armv7 on a pandaboard. Both, the >> miniroot-panda-63.fs and miniroot-panda-64.fs from Aug 24th panic with >> the following message: >> panic: pool_do_get: pvepl: page empty >> >> I'd appreciate any suggestions. >> Full console output below. >> Thanks >> Marcus > > Do you consistently see it? > > With the same U-Boot/snapshot version on a PandaBoard-ES > > U-Boot SPL 2018.03 (Mar 19 2018 - 23:59:15 -0600) > OMAP4460-GP ES1.1 > Trying to boot from MMC1 > SPL: Please implement spl_start_uboot() for your board > SPL: Direct Linux boot not active! > > > U-Boot 2018.03 (Mar 19 2018 - 23:59:15 -0600) > > CPU : OMAP4460-GP ES1.1 > Board: OMAP4 Panda > I2C: ready > DRAM: 1 GiB > MMC: OMAP SD/MMC: 0 > Loading Environment from FAT... *** Warning - bad CRC, using default > environment > > Failed (-5) > Net: No ethernet found. > Hit any key to stop autoboot: 0 > ## Error: "init_console" not defined > switch to partitions #0, OK > mmc0 is current device > SD/MMC found on device 0 > ** Unable to read file boot.scr ** > ** Unable to read file uEnv.txt ** > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > 57332 bytes read in 4 ms (13.7 MiB/s) > Found EFI removable media binary efi/boot/bootarm.efi > Scanning disks on usb... > Disk usb0 not ready > Disk usb1 not ready > Disk usb2 not ready > Disk usb3 not ready > Scanning disks on mmc... > MMC Device 1 not found > MMC Device 2 not found > MMC Device 3 not found > Found 3 disks > 89348 bytes read in 7 ms (12.2 MiB/s) > ## Starting EFI application at 82000000 ... >>> OpenBSD/armv7 BOOTARM 1.1 > boot> bsd.rd > booting sd0a:bsd.rd: > 2781028+452120+8055196+447940\[187370+107+206496+181684]=0xbbea20 > > OpenBSD/armv7 booting ... > arg0 0xc0ebea20 arg1 0xae7 arg2 0x88000000 > Allocating page tables > freestart = 0x80ebf000, free_pages = 258369 (0x0003f141) > IRQ stack: p0x80eed000 v0xc0eed000 > ABT stack: p0x80eee000 v0xc0eee000 > UND stack: p0x80eef000 v0xc0eef000 > SVC stack: p0x80ef0000 v0xc0ef0000 > Creating L1 page table at 0x80ec0000 > Mapping kernel > Constructing L2 page tables > undefined page pmap board type: 2791 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2018 OpenBSD. All rights reserved. https://www.OpenBSD.org > > OpenBSD 6.4-beta (RAMDISK) #38: Thu Aug 23 19:39:32 MDT 2018 > dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK > real mem = 1073741824 (1024MB) > avail mem = 1037377536 (989MB) > mainbus0 at root: TI OMAP4 PandaBoard-ES > cpu0 at mainbus0: ARM Cortex-A9 r2p10 (ARMv7) > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled > cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache > cortex0 at mainbus0 > amptimer0 at cortex0: tick rate 396000 KHz > armliicc0 at cortex0: rtl 7 waymask: 0x0000000f > omap0 at mainbus0 > omapid0 at omap0: omap4460 > amptimer0: adjusting clock: new tick rate 350000 KHz > prcm0 at omap0 rev 0.0 > ampintc0 at mainbus0 nirq 160, ncpu 2: "interrupt-controller" > omwugen0 at mainbus0 > simplebus0 at mainbus0: "ocp" > simplebus1 at simplebus0: "l4" > simplebus2 at simplebus1: "cm1" > simplebus3 at simplebus1: "cm2" > simplebus4 at simplebus1: "scm" > syscon0 at simplebus4: "scm_conf" > simplebus5 at simplebus1: "scm" > syscon1 at simplebus5: "omap4_padconf_global" > ompinmux0 at simplebus5 > simplebus6 at simplebus5: "omap4_padconf_global" > simplebus7 at simplebus1: "l4" > simplebus8 at simplebus7: "padconf" > ompinmux1 at simplebus8 > omgpio0 at simplebus0: rev 0.1 > gpio0 at omgpio0: 32 pins > omgpio1 at simplebus0: rev 0.1 > gpio1 at omgpio1: 32 pins > omgpio2 at simplebus0: rev 0.1 > gpio2 at omgpio2: 32 pins > omgpio3 at simplebus0: rev 0.1 > gpio3 at omgpio3: 32 pins > omgpio4 at simplebus0: rev 0.1 > gpio4 at omgpio4: 32 pins > omgpio5 at simplebus0: rev 0.1 > gpio5 at omgpio5: 32 pins > com0 at simplebus0: ti16750, 64 byte fifo > com0: probed fifo depth: 0 bytes > com1 at simplebus0: ti16750, 64 byte fifo > com1: probed fifo depth: 0 bytes > com2 at simplebus0: ti16750, 64 byte fifo > com2: console > com3 at simplebus0: ti16750, 64 byte fifo > com3: probed fifo depth: 0 bytes > tiiic0 at simplebus0 rev 0.11 > iic0 at tiiic0 > "ti,twl6030" at iic0 addr 0x48 not configured > "ti,twl6040" at iic0 addr 0x4b not configured > tiiic1 at simplebus0 rev 0.11 > iic1 at tiiic1 > tiiic2 at simplebus0 rev 0.11 > iic2 at tiiic2 > "ti,eeprom" at iic2 addr 0x50 not configured > tiiic3 at simplebus0 rev 0.11 > iic3 at tiiic3 > ommmc0 at simplebus0 > sdmmc0 at ommmc0: 8-bit > ommmc1 at simplebus0 > sdmmc1 at ommmc1: 1-bit > omdog0 at simplebus0 rev 0.1 > omdog1 at simplebus0 rev 0.0 > omehci0 at simplebus0 > usb0 at omehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "TI OMAP EHCI root hub" rev > 2.00/1.00 addr 1 > sdmmc1: can't supply clock > sdmmc1: can't enable card > scsibus0 at sdmmc0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SP16G, 0080> SCSI2 0/direct removable > sd0: 15193MB, 512 bytes/sector, 31116288 sectors > uhub1 at uhub0 port 1 configuration 1 interface 0 "Standard Microsystems > product 0x9514" rev 2.00/2.00 addr 2 > smsc0 at uhub1 port 1 configuration 1 interface 0 "Standard Microsystems > SMSC9512/14" rev 2.00/2.00 addr 3 > smsc0: address 02:22:01:5d:0d:70 > ukphy0 at smsc0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x0001f0, model 0x000c > softraid0 at root > scsibus1 at softraid0: 256 targets > bootfile: sd0a:/bsd > boot device: sd0 > root on rd0a swap on rd0b dump on rd0b > WARNING: CHECK AND RESET THE DATE! > erase ^?, werase ^W, kill ^U, intr ^C, status ^T > > Welcome to the OpenBSD/armv7 6.4 installation program. > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s > # >
