On Sun, Feb 25, 2018 at 09:37:50PM +0100, Mark Kettenis wrote: > Ordered myself one of these: > > https://www.pine64.org/?page_id=7147 > > and it arrived yesterday. Got the basics working already. Gigabit > Ethernet doesn't quite work yet and the device tree in mainline Linux > is broken and causes the USB bus not to be powered.
If you are using U-Boot master and Ethernet doesn't work from U-Boot you will likely need a patch to unbreak it. At least I did on RK3288. https://patchwork.ozlabs.org/patch/869785/ Though it seems there still isn't a config in U-Boot for this board. Are you using a custom config or a different tree such as https://github.com/ayufan-rock64/linux-u-boot ? > > Firmware situation isn't ideal as it currently relies on closed source > components from Rockchip that have a license that doesn't allow > redistribution. Apparently patches for U-Boot exist to avoid those > but those haven't landed in mainline U-Boot yet. > > > OpenBSD 6.2-current (GENERIC.MP) #25: Sun Feb 25 21:14:51 CET 2018 > > kette...@parry.sibelius.xs4all.nl:/home/kettenis/src/rock64/sys/arch/arm64/compile/GENERIC.MP > real mem = 2086510592 (1989MB) > avail mem = 1990930432 (1898MB) > mainbus0 at root: Pine64 Rock64 > cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4 > efi0 at mainbus0: UEFI 2.0.5 > efi0: Das U-boot rev 0x0 > psci0 at mainbus0: PSCI 1.0 > syscon0 at mainbus0: "syscon" > rkclock0 at mainbus0 > syscon1 at mainbus0: "syscon" > ampintc0 at mainbus0 nirq 160, ncpu 4 ipi: 0, 1: "interrupt-controller" > rkpinctrl0 at mainbus0: "pinctrl" > rkgpio0 at rkpinctrl0 > rkgpio1 at rkpinctrl0 > rkgpio2 at rkpinctrl0 > rkgpio3 at rkpinctrl0 > simplebus0 at mainbus0: "amba" > agtimer0 at mainbus0: tick rate 24000 KHz > com0 at mainbus0: ns16550, no working fifo > com0: console > rkiic0 at mainbus0 > iic0 at rkiic0 > rkpmic0 at iic0 addr 0x18: RK805 > dwmmc0 at mainbus0: 96 MHz base clock > sdmmc0 at dwmmc0: 4-bit > dwmmc1 at mainbus0: 0 MHz base clock > sdmmc1 at dwmmc1: 8-bit > dwge0 at mainbus0 > dwge0: address: 82:ab:2b:8e:96:47 > rgephy0 at dwge0 phy 0: RTL8169S/8110S/8211 PHY, rev. 6 > rgephy1 at dwge0 phy 1: RTL8169S/8110S/8211 PHY, rev. 6 > ehci0 at mainbus0 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev > 2.00/1.00 addr 1 > cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4 > cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4 > cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4 > scsibus0 at sdmmc0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, BB2MW, 0030> SCSI2 0/direct removable > sd0: 30543MB, 512 bytes/sector, 62552064 sectors > sdmmc1: can't enable card > cdce0 at uhub0 port 1 configuration 2 interface 0 "TP-LINK USB 10/100/1000 > LAN" rev 2.10/30.00 addr 2 > cdce0: address f4:f2:6d:18:1a:e2 > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > bootfile: sd0a:/bsd > boot device: sd0 > root on sd0a (945c5b02147ba041.a) swap on sd0b dump on sd0b >
