PEBCAK... Obviously I did not use current, but 6.2. (I happily clicked from openbsd.org/armv7.html to install instructions, which put me into /6.2/)
Will test again with current now. Sorry for the noise. regards, Robert On Fri, 5 Jan 2018 11:56:13 +0100 Robert <info...@die-optimisten.net> wrote: > Hi, > > I'm trying to install OpenBSD to the SD card on a Banana Pi M2+, but I get > "Input/output error" when I try to access the SD card. > > Preparations (current/20180103): > 1) dd if=miniroot-cubie-62.fs of=/dev/rsdXc > 2) dd if=/usr/local/share/u-boot/orangepi_plus/u-boot-sunxi-with-spl.bin > of=/dev/sdXc bs=1024 seek=8 > 3) mount sdXa and replace dtb with sun8i-h3-bananapi-m2-plus.dtb > > The installer boots without problems and I can access and use the internal > NAND (sd1). > But accessing the SD card (sd0) gives: > > # fdisk sd0 > > fdisk: sd0: Input/output error > > It takes about 10 seconds until the error appears. > > I also noted that the NAND sometimes shows up as sd0 and the SD as sd1 (if > that's relevant...). > Armbian works fine using the same SD, so the hardware seems to be ok. > > Any suggestions? > > regards, > Robert > > > U-Boot 2017.09 (Oct 02 2017 - 19:15:15 -0600) Allwinner Technology > > CPU: Allwinner H3 (SUN8I 1680) > Model: Xunlong Orange Pi Plus / Plus 2 > DRAM: 1 GiB > MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1 > *** Warning - bad CRC, using default environment > > In: serial > Out: vidconsole > Err: vidconsole > Net: phy interface7 > eth0: ethernet@1c30000 > starting USB... > USB0: USB EHCI 1.00 > USB1: USB EHCI 1.00 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 1 for devices... 1 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:1... > Found EFI removable media binary efi/boot/bootarm.efi > reading efi/boot/bootarm.efi > 67372 bytes read in 39 ms (1.6 MiB/s) > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > ## Starting EFI application at 42000000 ... > Scanning disks on usb... > Scanning disks on mmc... > ** First descriptor is NOT a primary desc on 1:1 ** > MMC Device 2 not found > MMC Device 3 not found > Found 6 disks > >> OpenBSD/armv7 BOOTARM 1.0 > boot> > cannot open sd0a:/etc/random.seed: No such file or directory > booting sd0a:/bsd: 2300416+7988936+446336 [174378+90+319856+152368]=0xae1634 > > OpenBSD/armv7 booting ... > arg0 0xc0de1634 arg1 0x0 arg2 0x48000000 > Allocating page tables > freestart = 0x40de2000, free_pages = 258590 (0x0003f21e) > IRQ stack: p0x40e10000 v0xc0e10000 > ABT stack: p0x40e11000 v0xc0e11000 > UND stack: p0x40e12000 v0xc0e12000 > SVC stack: p0x40e13000 v0xc0e13000 > Creating L1 page table at 0x40de4000 > Mapping kernel > Constructing L2 page tables > undefined page pmap board type: 0 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2017 OpenBSD. All rights reserved. https://www.OpenBSD.org > > OpenBSD 6.2 (RAMDISK) #85: Wed Oct 4 01:11:47 MDT 2017 > dera...@armv7.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK > real mem = 1073741824 (1024MB) > avail mem = 1038311424 (990MB) > mainbus0 at root: Xunlong Orange Pi Plus / Plus 2 > cpu0 at mainbus0: ARM Cortex-A7 r0p5 (ARMv7) > cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled > cpu0: 32KB(32b/l,2way) I-cache, 32KB(64b/l,4way) wr-back D-cache > cortex0 at mainbus0 > sxiccmu0 at mainbus0 > psci0 at mainbus0 > agtimer0 at mainbus0: tick rate 24000 KHz > simplebus0 at mainbus0: "soc" > sxiccmu1 at simplebus0 > sxipio0 at simplebus0: 94 pins > sxipio1 at simplebus0: 12 pins > syscon0 at simplebus0 > sximmc0 at simplebus0 > sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma > sximmc1 at simplebus0 > sdmmc1 at sximmc1: 4-bit, sd high-speed, mmc high-speed, dma > sximmc2 at simplebus0 > sdmmc2 at sximmc2: 8-bit, sd high-speed, mmc high-speed, dma > ehci0 at simplebus0 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev > 2.00/1.00 addr 1 > ehci1 at simplebus0 > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 configuration 1 interface 0 "Generic EHCI root hub" rev > 2.00/1.00 addr 1 > sxidog0 at simplebus0 > com0 at simplebus0: ns16550, no working fifo > com0: console > dwxe0 at simplebus0: address 02:81:00:24:f1:70 > rgephy0 at dwxe0 phy 0: RTL8169S/8110S/8211 PHY, rev. 5 > rgephy1 at dwxe0 phy 1: RTL8169S/8110S/8211 PHY, rev. 5 > ampintc0 at simplebus0 nirq 160, ncpu 4 > sxirtc0 at simplebus0 > gpio0 at sxipio0: 32 pins > gpio1 at sxipio0: 32 pins > gpio2 at sxipio0: 32 pins > gpio3 at sxipio0: 32 pins > gpio4 at sxipio0: 32 pins > gpio5 at sxipio0: 32 pins > gpio6 at sxipio0: 32 pins > gpio7 at sxipio1: 32 pins > sximmc0: timeout updating clock > sdmmc0: can't change bus clock > sdmmc0: mem init failed > scsibus0 at sdmmc0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SC64G, 0080> SCSI2 0/direct removable > sd0: 60906MB, 512 bytes/sector, 124735488 sectors > scsibus1 at sdmmc2: 2 targets, initiator 0 > sd1 at scsibus1 targ 1 lun 0: <Samsung, 8WPD3R, 0000> SCSI2 0/direct removable > sd1: 7456MB, 512 bytes/sector, 15269888 sectors > (manufacturer 0x2d0, product 0xa9a6)at sdmmc1 function 1 not configured > (manufacturer 0x2d0, product 0xa9a6)at sdmmc1 function 2 not configured > boot device: sd0 > disklabels not read: sd0 sd1 > root on rd0a swap on rd0b dump on rd0b > WARNING: preposterous clock chip time > WARNING: CHECK AND RESET THE DATE! > erase ^?, werase ^W, kill ^U, intr ^C, status ^T > > Welcome to the OpenBSD/armv7 6.2 installation program. > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? s > # fdisk sd0 > > sximmc0: timeout updating clock > fdisk: sd0: Input/output error > # >
