Hi!
Had some time to play with my year old HummingBoard Pro with i4Pro SOM.
I had some small problems.
The ramdisk has wd0, wd1 and sd0. I think sd1 should be added.
I cant find any wd-devices in armv7 GENERIC, so wd* might
be removed from MAKEDEV and name2blk.
The kernel print:
boot device: sd0
root on sd1a (88c7681c88fe6521.a) swap on sd1b dump on sd1b
The boot device line is incorrect. It should be sd1.
-moj
OpenBSD 6.0-beta (GENERIC) #276: Sat Jul 9 12:44:52 AEST 2016
j...@armv7.jsg.id.au:/usr/src/sys/arch/armv7/compile/GENERIC
real mem = 2147483648 (2048MB)
avail mem = 2097717248 (2000MB)
mainbus0 at root: SolidRun HummingBoard Dual/Quad
cpu0 at mainbus0: ARM Cortex A9 R2 rev 10 (ARMv7 core)
cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
cpu0: 32KB(32b/l,4way) I-cache, 32KB(32b/l,4way) wr-back D-cache
cortex0 at mainbus0
ampintc0 at cortex0 nirq 160
amptimer0 at cortex0: tick rate 396000 KHz
armliicc0 at cortex0: rtl 7 waymask: 0x0000000f
imx0 at mainbus0
imxocotp0 at imx0
imxccm0 at imx0: imx6 rev 1.5 CPU freq: 792 MHz
imxiomuxc0 at imx0
imxgpio0 at imx0
imxgpio1 at imx0
imxgpio2 at imx0
imxgpio3 at imx0
imxgpio4 at imx0
imxgpio5 at imx0
imxgpio6 at imx0
ehci0 at imx0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
ehci1 at imx0
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "i.MX6 EHCI root hub" rev 2.00/1.00 addr 1
simplebus0 at mainbus0: "soc"
simplebus1 at simplebus0: "aips-bus"
simplebus2 at simplebus1: "spba-bus"
imxuart0 at simplebus2: console
imxdog0 at simplebus1
simplebus3 at simplebus1: "anatop"
simplebus4 at simplebus0: "aips-bus"
fec0 at simplebus4
fec0: address d0:63:00:00:00:00
atphy0 at fec0 phy 0: F1 10/100/1000 PHY, rev. 2
imxesdhc0 at simplebus4
imxesdhc0: 198 MHz base clock
sdmmc0 at imxesdhc0: 4-bit, mmc high-speed, dma
imxesdhc1 at simplebus4
imxesdhc1: 198 MHz base clock
sdmmc1 at imxesdhc1: 4-bit, mmc high-speed, dma
imxiic0 at simplebus4
iic0 at imxiic0
pcfrtc0 at iic0 addr 0x68: battery low
"fsl,sgtl5000" at iic0 addr 0xa not configured
imxiic1 at simplebus4
iic1 at imxiic1
imxuart1 at simplebus4
ahci0 at simplebus0: AHCI 1.3
ahci0: port 0: 3.0Gb/s
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, Samsung SSD 850, EMT4> SCSI3 0/direct fixed
naa.5002538d40a5a2e1
sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
simplebus5 at mainbus0: "regulators"
scsibus1 at sdmmc1: 2 targets, initiator 0
sd1 at scsibus1 targ 1 lun 0: <SD/MMC, SU08G, 0080> SCSI2 0/direct fixed
sd1: 7580MB, 512 bytes/sector, 15523840 sectors
uhub2 at uhub0 port 1 "Cypress Semiconductor USB2.0 Hub" rev 2.00/32.99 addr 2
sdmmc0: can't enable card
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
boot device: sd0
root on sd1a (88c7681c88fe6521.a) swap on sd1b dump on sd1b
