On 02/06/14 20:31, philippe Valade wrote:
>On 02/06/14 18:14, Fred wrote:> On 02/06/14 18:04, philippe Valade wrote:
>>> Hi
>>>
>>> I am stuck trying to install the Openbsd/armv7 port into a
>>> Cubieboard
>>> A10.
>>>
>>> So I prepared the SD card using the miniroot-sunxi.55.fs,
>>> connect the
>>> serial console and boot the cubieboard.
>>>
>>> At this point everything
>>> goes well
>>> and I reach the first question about what I want to do.
>>>
>>> (I)nstall,
>>> (U)pgrade,(A)uto Install, (Shell)
>>>
>>> Answer few more questions and reach the
>>> point where I have
>>> to select the destination disk.
>>>
>>> Unfortunately the system
>>> tells me that the Available disks
>>> are ¿None¿.
>>>
>>> I do not know what I can do
>>> with this.
>>>
>>>
>>>
>>> Any idea will be welcome.
>>>
>>> Thanks.
>>>
>>
>> Can you get the dmesg from the Ramdisk - it might give a clue as to why
>> no disks are showing up....
>>
>> hth
>>
>> Fred
>>
>Hi, thanks for the quick reply
>
>unfortunatly the dmesg does not tell me much!?
>------------------------------------------------------------------
># dmesg
>OpenBSD 5.5-beta (RAMDISK-SUNXI) #2: Thu Jan 16 23:07:47 EST 2014
> r...@bbb1.openbsd.org:/usr/src/sys/arch/armv7/compile/RAMDISK-SUNXI
>real mem = 1073741824 (1024MB)
>avail mem = 1036263424 (988MB)
>mainbus0 at root
>cpu0 at mainbus0: ARM Cortex A8 R3 rev 2 (ARMv7 core)
>cpu0: DC enabled IC enabled WB disabled EABT branch prediction enabled
>cpu0: 32KB(64b/l,4way) I-cache, 32KB(64b/l,4way) wr-back D-cache
>sunxi0 at mainbus0: A1X
>sxipio0 at sunxi0
>sxiccmu0 at sunxi0
>a1xintc0 at sunxi0
>sxitimer0 at sunxi0: ticktimer 100hz @ 32KHz
>sxitimer1 at sunxi0: stattimer 128hz @ 32KHz
>sxitimer2 at sunxi0: cntrtimer @ 32KHz
>sxidog0 at sunxi0
>sxirtc0 at sunxi0
>sxiuart0 at sunxi0: console
>sxiuart1 at sunxi0
>sxiuart2 at sunxi0
>sxiuart3 at sunxi0
>sxiuart4 at sunxi0
>sxiuart5 at sunxi0
>sxiuart6 at sunxi0
>sxiuart7 at sunxi0
>sxie0 at sunxi0, address 02:13:04:c2:45:00
>rlphy0 at sxie0 phy 1: RTL8201L 10/100 PHY, rev. 1
>ahci0 at sunxi0 AHCI 1.1
>scsibus0 at ahci0: 32 targets
>ehci0 at sunxi0
>usb0 at ehci0: USB revision 2.0
>uhub0 at usb0 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1
>ehci1 at sunxi0
>usb1 at ehci1: USB revision 2.0
>uhub1 at usb1 "Allwinner EHCI root hub" rev 2.00/1.00 addr 1
>boot device: lookup '' failed.
>root on rd0a swap on rd0b dump on rd0b
>WARNING: clock lost 1477 days
>WARNING: CHECK AND RESET THE DATE!
>-----------------------------------------------------------
>
>
>This board should have 4 Go integrated flash
>The minitroot-sunix.55.fs is written into a 8 Go SD
>I also plugged a sata Hard disk of 2 To
>
Hi Philippe,
Thats not looking too promising - I'm not sure of the status of the
Cubieboard port for armv7 [1] - all the boards are in active development
at the moment, but the kernel doesn't seem to recognise any of the
attached storage.
Hopefully one of the developers will be able to point out what's missing...
Cheers
Fred
[1] http://marc.info/?l=openbsd-arm&m=137870706314175
